Freewing 90mm V2 F16 6S FPV Setup
ฝัง
- เผยแพร่เมื่อ 18 ต.ค. 2024
- This is the Setup video for the 90mm F16.
Parts used.
Motionrc V2 F16 6s
www.motionrc.c...
Dji Goggles 2
www.getfpv.com...
O3 Air unit Camera vtx system
www.getfpv.com...
Motionsic Rc BAG gimbal
fpvdogfight.co...
Motionsic Tally ho Head tracker
fpvdogfight.co...
Motionsic RC ARMS sight
fpvdogfight.co...
Matek H743 WLite FC
www.getfpv.com...
Matek air speed sensor
www.getfpv.com...
Matek GPS Antenna
www.getfpv.com...
Matek Hall effect Current meter
www.getfpv.com...
Jumper T15
www.getfpv.com...
Express LRS Happy Model Receiver
www.getfpv.com...
FPV TOYS Gauge controller
www.fpvtoys.ne...
FPV Toys Screen
www.fpvtoys.ne...
9x9x5 Heatsinks for Air Unit
www.amazon.com...
40mm Brushless fan
www.amazon.com...
Regulator for fan
www.amazon.com...
Gimbal setup
• Easy Head Tracker Setu...
• How to Calibrate Tally...
Inav tutorial
• INAV for Beginners 202...
Inav Tuning
• 🌟INAV🌟 Fixed Wing PERF...
V2 F16 3d printed parts
www.thingivers...
www.thingivers...
Your builds are so meticulous & clean! I’m hoping to build a fpv F22 in the near future.
Good work on that jet . The perfection is goals !
yooo thats a big one :)
I started flying wings too :)
nice 👍👍👍
Wow thank you for this video I want to move to a fc now . Can’t wait to see your next projects .
I love that plane
suparrrrrrr coolllllllll men 💯
Very informative, very clean build I’m impressed with the outcome
Looking good Kelvin!
Super cool
next step is obviously a hotas right?
Great pursuit
@@thefpvyawthority8106 thanks blue
I expect nothing less from you. Good to see ya even if it was just on a video.
@deadringerfpv6412 thanks bro.....been too long.
The attention to detail here is top notch. Nice work! How can i make the canopy more clear?
Clean with microfiber and windex or ammonia , then spray again after wiping just to clear off any impurities , leave the spray on there and dip it in quickshine floor shine . Let it sit in a seal container to avoid any fibers and dust settling on it while it cures . Leave it for 48 hours and re dip it until you get the result you want
@@tonyyimbo thanks, I'll try that
@RyanQuellet thanks Ryan. I use chemical guys ultra fine car polish. I polish about 3-4 times with a microfiber. Then I follow with a automotive ceramic coat. I do this process to both the inside and out side of canopy.
Are you using a voltage regulator to the fan because the power is coming directly from the battery? Can you connect it to the 5v voltage supply on the flight control board or an RC type BEC?
@stephanbrown6724 yes. I'm going straight to the battery with a 12v fan and regulator. I didn't use a supply off the board to prevent any chance of browning out the system. I wasnt sure if 12v/9v rail rail on the fc would handle the load of a fan and the o3 air unit
i spy a tbs caipirinha on the wall…
@@hankyates yes sir. Still got it.