Konica Minolta Bizhub 165 Replacing the OPC drum.

แชร์
ฝัง
  • เผยแพร่เมื่อ 29 ส.ค. 2024
  • During the operation of the copier, the photo drum is often worn or scratched. How to change the OPC drum and cleaning blade in a Konica Minolta bizhub 165/164/185 copier is explained in this video.If you watch this video until the very end, you will definitely be able to replace the photo drum in your conditions! I am ready to help you with advice - contact me!
    ======================================================================
    При роботі копіювального апарата часто зношується або царапається фотобарабан. Як поміняти фотобарабан та лезо очистки в копіювальному апараті Коніка Минолта bizhub 165/164/185 у цьому відео.

ความคิดเห็น • 15

  • @raulkonica7005
    @raulkonica7005 ปีที่แล้ว +1

    Gracias por el vídeo, colega!

    • @rivprint
      @rivprint  ปีที่แล้ว +1

      Thank you very much for the rating dear!

  • @user-jm4uf6dh7m
    @user-jm4uf6dh7m ปีที่แล้ว +1

    Як завжди професійно і зрозуміло!!! 😊

    • @rivprint
      @rivprint  ปีที่แล้ว +1

      Дякую за постійні перегляди та оцінку моїх відео!

  • @anandsurpur8072
    @anandsurpur8072 10 หลายเดือนก่อน +1

    165 e minolta. Squeeking sound while copying. Reason..

    • @rivprint
      @rivprint  10 หลายเดือนก่อน

      Thanks for the question!

    • @rivprint
      @rivprint  10 หลายเดือนก่อน

      There could be several reasons... Rubber roller in the paper feed tray. Wash! Drum cleaning blade. Sprinkle with toner, talcum powder or baby powder. Plastic photo drum bushings. Try to substitute another one to see if that is the reason.

  • @anandsurpur8072
    @anandsurpur8072 9 หลายเดือนก่อน

    Minolta 165 e. Toner & developer unit both steel, black screws slipping. Any tips?

    • @rivprint
      @rivprint  9 หลายเดือนก่อน

      If I understand you correctly, the screws that connect the photodrum unit and the developer unit are not fixed?

    • @rivprint
      @rivprint  9 หลายเดือนก่อน

      Try choosing a single-core wire with a small cross-section or something similar. Install into the problem hole before installing the screw. Tighten the screw. Must hold.

    • @rivprint
      @rivprint  9 หลายเดือนก่อน

      Another option... carefully coat the inside of the hole with a small amount of super glue. Wait a few seconds. Then try tightening the screw.

    • @anandsurpur8072
      @anandsurpur8072 9 หลายเดือนก่อน

      @@rivprint instead coating inside hole, if we coat glue on the screws only.. Which is better option?

    • @rivprint
      @rivprint  9 หลายเดือนก่อน

      Usually I put a drop of glue inside, wait a little and screw it on. But you can apply glue to the screw itself - that’s also not bad) But now I just insert the wire (small cross-section monowire), twist it and bite off the excess. It holds up well, try it!@@anandsurpur8072