Surface Cleaner bearing replacement
ฝัง
- เผยแพร่เมื่อ 1 ม.ค. 2017
- This is a Mi-T-M surface cleaner used with a 3500 psi pressure washer or bigger. You can't get the bearings from Mi-T-M, you can only purchase the whole housing that has the 2 bearings already installed which is around $125.00. I got the bearing from Bearings Plus for about $17.00 plus shipping which came out to around $25.00. The bearing is 42mmX15mmX13mm.
- แนวปฏิบัติและการใช้ชีวิต
Fucking A+ bro I have a edou 20inch, this just made me me confident af, love it, TH-cam is the dad I never had
Lmao
i have the edou 20 inch will these fit that size?
Great video. 6302 bearing. For mine, I used an S6302-2RS, stainless with two rubber seals. $6 each (2 required) on Amazon.
Great video, thanks! I appreciate that you added the comments.
Thank you
This was very helpful thank you
You are welcome
Upon pushing the bearings back into the housing, he should have never hammer it back in. You just end up scratching the inside.
Just apply little grease inside the bearing housing and outside the bearings itself and it should slide in like butter.
Also apply small grease between the first bearing and the second as you pushed them done on the piston if you like to call it piston. It will work flawlessly.
Thank me later
Are there any o-rings to replace? How does it seal water in? Do you have to take 4 cap screws and locknuts off? I am about to tear a 20" one apart.
There are no o-rings. All the water goes threw the very center casting. The outer casting then clamps around it. Yes the cap screws and lock-nuts had to come off on this model. The failure in the design comes from not having sealed bearings, and not having the ability to grease the bearings. I hope that this helps you in your repair. Keep on fixin.
No my friend. There’s O ring to replace inside the house and a small one at the very bottom of the housing.
Jeremy, the ring you pulled out at 2:10 do you know what size it is. I brought mine and no store around here in my area has one.
I don't. Try going to Fastenal they have every size.
@@jeremyraeber4234 ty bud
Good video, that swivel looks like the same one on the GP Hammerhead, the BE, Whirl A Way and a couple others, in your opinion is it the same swivel? Thank you.
I've finally was able to view the ones you mentioned in person and yes its swivel.
Same swivel
Great video! Where did you get those pliers from?
Home Depot believe it or not.
What is the bearing number?
Is this a Mi T M surface cleaner?? My beavis locking up on me on a job right now and I don't know how to fix it
Yes it is.
On my lanz surface cleaner the rotating rod falls out.oes the clip stop that
Deep groove bearings?
Just a sealed ball bearing bearing.
thank you....did yours lose power when it went bad
It did . Then it froze.
What size are those bearings
42mmx15mmx13mm
What size bearing are they do you have the number.
42mm×15mm×13mm
I like that background music.. who?
Would this same concept apply to simpson surface cleaners?
It will on the 20", but not on the 15" wand connect.
Jeremy Raeber yeah I have the 20” similar to that except I can’t get the arms where the tips connect off the main shaft below where the bearings are.
On yours it’s one long bar. On mine it’s two pieces. I can’t find a diagram anywhere. Do some have Allen keys or refers threading?
U didn't Evan grease It u wrongun
That's because you don't grease sealed bearings. That's why they are called sealed.
@@jeremyraeber4234 so they never get greased then. They can't last long
@@xxdeedee why be rude to someone whos trying to be helpful?
No they don't. Google sealed bearings and read. Call the manufacturers.