MAKITA DUR181Z Strimmer line replace / Install new string trimmer line

Here I show you how to replace worn out /used up string trimmer line on the cordless 18 volt makita dur181 single line stimmer / weed whacker
Please subscribe my channel and like this video as its always appreciated. Thanks.
Akuoly 100m Strimmer Line Mower Line Round 1.6mm
amzn.to/3OSLLN8
Makita DUR181Z 18V LXT Cordless Grass Line Trimmer Strimmer Body Only
amzn.to/4340qZN
Disclaimer: The links above are amazon affiliate links. If you use these links to make a purchase, I may earn a small commission at no additional charge to you which helps support the channel
Disclaimer; This video is for guidance only, as any project always wear the correct safety ppe and follow all safety guidelines.
Please also be advised that this video is only a guide and I accept no responsibility for any injuries loss or damage occurred while following this video.

[@erniepenny221]

Thanks Mick, just what was required, regards from N.Z

[@jameseruera9642]

great help, thanks for sharing, maybe try outdoors for more lighting

[@micksmaintenanceanddiy]

Thanks,Yeah sometimes the go pro camera can flicker with the led lights in the workshop so kept the lighting to a minimum.

[@callmeoz2554]

Lifesaver. TY!!!!

[@matpage1456]

Thank you mate legend

[@jovosedlar3395]

Turn the light on, it is so dark and hard to see in the future. Other than that good video, thank you.

[@BulleDK]

Thanks a lot from Denmark

[@micksmaintenanceanddiy]

Glad it helped.

[@dominicjohnson8427]

Spot on many thanks

[@arykesdeminno4389]

Thank you 🙏 😊 😊

[@colodezwells4026]

Thank you

[@micksmaintenanceanddiy]

You're welcome.

[@gabo4558]

Thanks.

[@babyka4781]

Отлично бро. 😊

[@micksmaintenanceanddiy]

You're welcome.

[@Lunatickdr]

Спасибо!

[@nukeallxxx]

thanks

[@Peter-yn8uy]

Perfect, thanks for your help.

[@micksmaintenanceanddiy]

Your welcome.

[@allotmentjiggerypokery2150]

Thanks that was useful to know

[@micksmaintenanceanddiy]

Glad it was helpful!

[@geertdepickere5501]

Hi, I have a DUR193Z with the exact same mechanism.
It is brand new but I have a major problem with it: The line keeps breaking (after using it for 30 seconds) right where it comes out of that whole. I then have to each time take out the head, unwind the wire 10 cm, stick it through that hole again, reassemble the head after which I can again use it for another 30 seconds to a minute. Drives me crazy.
Any ideas?

[@darrenstirrup5516]

Excuse for asking this but r u aware that u have to bump the line out😂

[@geertdepickere5501]

@@darrenstirrup5516 Yes I am aware of that. But when the line breaks at the exit hole no line sticks out anymore and bumping does not help in that case.
And the line always seems to break right there in my case. Looks like a design flaw to me...

[@darrenstirrup5516]

@@geertdepickere5501 hmm sounds like a fault like u say.

[@antasosam8486]

Try another type of string, like round profile (cheap actually) and dont be so agressive on corners. Also check for sharp corners of gadget, this may be defects of manufacture, highy unprobable.

[@tomwalton6661]

I have same problem!🙄 same model!

[@gosk8inben]

Instructions were ass. Thank you.

[@micksmaintenanceanddiy]

Glad it helped.

[@rachaelrobcar]

Great content just too dark to follow the video.

[@micksmaintenanceanddiy]

Thanks, the Go pro I use is an older model and not the best in low lighting conditions.

[@gediminasradvila9738]

Too dark video.😢

[@downunda107]

Brill tx 🦘✌️