Servicing D5/D10 electric gate opener?

#D5#disassembly #hackopen/D10slider#expresss#gateopener.Opening a #centurion machine #D5 for the sole goal of showing technicians and gate lovers the components that make up a gate opener

[@Hollyhock-n8h]

How to replace seals? Not enough light for video.

[@jonathangeorge7417]

lighting was poor in the video. wasnt able to see properly

[@fuzzs8970]

Thank you. What needs to be done to replace the seals if there's a gearbox oil leak

[@MayurHarkison]

i also want to knwo which seals to replace if oil is coming with the counting disc

[@yashgupta1633]

Sir, what to do if the motor shows no limit set, no origin found, max collision. Kindly give the solution separately. Thank you

[@josephmarongo6358]

Next service please make sure of circlip pliers to remove the circlip. Not professional.

[@octamy-qn8hl]

how can you work in the dark? install & put some lamp light on then i will subscribe

[@siphamandlabuthelezi3219]

My gate motor has an error saying gate installed then when moving its stops then say gate motor faulty what could be the problem

[@nathanieldelouw2582]

Sounds like you explaining my marriage, great job, how do I get in touch with you?

[@mosesyika1771]

I'm proud of you, keep up the good videos

[@manyanyato]

Dude...the lighting

[@greyalien6309]

You should buy and use the correct tools to show people the correct way to do things. A pliers is not a hammer, and a screwdriver is not a circlip pliers. You are a bush mechanic.

[@wellyvideos]

Don't be jealous. The guy is good.

[@fuzetechfuzetech5854]

My gate is written setup limits and upon settings it runs and restarts itself like power off and on. What could be the reason?

[@expressautomationstechmast7029]

Battery could be faulty

[@preshnaidoo1043]

Thanks, was just what I was looking for

[@siyabongamdlalose4475]

Please assist I damaged the threads of the key for changing the motor from manual to auto

[@jacowentzel723]

Thanks.
Good video 👍

[@stephenwebb3069]

Thank you this was very very helpful

[@johanreyneke5837]

Very informative. Thank you for the post.

[@ashleynkoe2687]

thanks for the video, my manual release wont release the gear what could be the problem

[@casperniemand]

How do you remove the dos wheel in order to replace the oil seal behind the dos wheel? Thanks in advance

[@expressautomationstechmast7029]

Unscrew the four screw holding the lead , that is , after removing the sprocket

[@silumesiisitwala4238]

@@expressautomationstechmast7029 I have an error "gate motor failure". How do I rectify it?

[@expressautomationstechmast7029]

The motor might be faulty or the dose sensor faulty/not in place.

[@mirriamkubangu1396]

Thank you

[@expressautomationstechmast7029]

Get to know what's inside a #D5 EVO Slider machine!

[@gideonadjei4130]

What is the cause for a D5 motor to open and cannot be able to close after putting it on manual still you cannot close the gate

[@expressautomationstechmast7029]

@@gideonadjei4130 When the gate is in auto mode, make sure all safety beams loop are in place.When the gate is manual mode, First make sure you have manualised the gate by turning the round wheel in the direction shown on wheel. If gate doesn't move in manual mode then you will have to open the D5 and service the gear releasing mechanism

[@gideonadjei4130]

@@expressautomationstechmast7029 Okay sir, thank you for the information

[@chrishabib5325]

This video was really helpful. How can I contact you, I have something to discuss with you

[@expressautomationstechmast7029]

Send an email : [e-mail]

[@jay_Mus]

how can we contact you

[@chastomes7154]

How do remove the the doss wheel

[@welcomegauche6870]

Thank you so much🤓

[@cass733]

Not so informative , the lighting is bad

[@fuzzs8970]

Just adjust the brightness of your screen you will be able to watch it. However it doesn't show how to dismantle the shaft to remove the doss wheel

[@fuzzs8970]

I can try to help you if you need some help. I have installed mine and serviced mine for like 15 years. Let me know I'll try if you want

[@marcoclarke1436]

can you show how to replace the bearings of the same motor

[@cyrilpercimoney7611]

How do you top up the oil? Is it through the dipstick pipe?

[@expressautomationstechmast7029]

Yes! Oil top up seldom happens,unless there is a leakage in the machine!

[@cyrilpercimoney7611]

Thanks!!

[@charleschimfwembe5528]

@@expressautomationstechmast7029 and how do you replace a leaking seal?