Hello Could you please suggest any other alternative battery as this is costly and even the ubec converter? And also do I've to make changes after replacing the components?
One more thing as the video suggests to use glue gun for placements of components, but I want to use these components for various projects so what to do instead of sticking, specially the servo motors and tt motors
Now TT motors are rotating continuously when I give 12V supply?couldn’t control with joystick but servo is rotating 90 degree while pressing joystick.What to do?
Another issue I'm facing now, when I move forward or reverse in analog joystick,the TT motors are rotating continuously but if I connect left motors and right motors separately to the motor drive, I can control the TT motors but if I connect both side motors together , It is rotating continuously if I move forward or reverse in analog joystick? What to do??
@@roscoe3dp470 Just came across this comment and would like to let you know that I have created car using PS3 controller. Not sure if you already checked that video. Hope it will be helpful. 👍
Thank you very much for checking out the video👏🏻👍🏻. Actually I was watching some old video of such car and this idea came in mind why not make DIY model of this car using esp32 . That’s why I made this as a hobby project . I am glad you liked it 👍🏻👌🏻
@@hashincludeelectronics I also see this kind of schematics without the use of an UBEC. Did you have problems when using the 5V of the Electronic Speed Controller?
Thanks for checking out the video 👍🏻. You can use esp8266 but for that you might need to make some changes in code as I have used ESP32Servo library , wifi library . So you need to use corresponding library for esp8266. And also make sure the pins I have used are available on esp8266 else change those pins . Give it a try and I will help you if any issue .
@@na.h5929 ok . There is some small code change in transmitter code so that it will work on this IDE . Change this line as below in transmitter code esp_now_peer_info_t peerInfo = {};
When i press the switch in joystick,the serve rotates 90 degree and when i move the motors ,the servo quickly comes to it's initial position without pressing the joystick switch. Is the anything to modify in code? Or anyother mistake??
@@tamilarasan1389 which power supply are you using ? Make sure it’s rechargeable battery and provides more than 3 A current . Power supply interruption can cause esp32 to reset .
Hi sir,I have two doubts 1.I'm using Dev module instead of Wrover module ,will there be any changes, if so tell me sir? 2.Is it mandatory to use Wifi101/WifiNINA firmware updater(tools>firmware updater),If so tell me how to set that?
by the way i succes to follow your project in this video, but can you help me... make code for control servos with joystick please🙏 i really need this on my project😭
You are going amazing work ! keep up !
Thanks for checking out the video. Cheers 👍🏻
I like ur video and explain step by step..
Thank you for your Post...
Great Job
Congratulations 👏🥳
Thank you very much for your kind words 🙂👍🏻
Bro u are genius
👍👌
amazing idea
Thank you! Cheers!
Wow
Thank you 👍🏻👌🏻
Hi loved it … can I use esp 32 wroom-32 ? Instead of 38 pins ?
I would recommend to use esp32 38 pin to avoid any issue 👏🏻👍🏻
And also do we have to port the mac address in the receiver or directly the main code ?
You need to get the max address and put it in code 👍🏻👏🏻please check this step in video
Hello
Could you please suggest any other alternative battery as this is costly and even the ubec converter?
And also do I've to make changes after replacing the components?
You can use LiOn battery cells . Each cell is 3.7V so you can use 3 cells 👏🏻👍🏻
One more thing as the video suggests to use glue gun for placements of components, but I want to use these components for various projects so what to do instead of sticking, specially the servo motors and tt motors
@@Mahek-rs8tv you can screw those components on chassis. Or use other methods which is handy for you 👏🏻👍🏻
Sir please give program for receiver ESP32 for simple forward and reverse of 2 motors working individually with joystick.
Please check my video on ESPNOW car using joystick 👍🏻👏🏻
Now TT motors are rotating continuously when I give 12V supply?couldn’t control with joystick but servo is rotating 90 degree while pressing joystick.What to do?
Please check the connections for power 👍🏻👏🏻
Another issue I'm facing now, when I move forward or reverse in analog joystick,the TT motors are rotating continuously but if I connect left motors and right motors separately to the motor drive, I can control the TT motors but if I connect both side motors together , It is rotating continuously if I move forward or reverse in analog joystick? What to do??
Please check the connections 👍🏻👏🏻
What is the alternate for 12V battery as it’s costlier
You can use LiOn 3 cells battery 👍🏻👏🏻
Can we use 2 cell18650 i stead of battery
Yes go for it .
Awesome project, can you use a PS3 controller instead of the joystick ?
Thanks for checking out the video 👍🏻. I have not tried ps3 controller yet but should not be that difficult ☝️
@@hashincludeelectronics I'd love to see it working.
@@roscoe3dp470 Just came across this comment and would like to let you know that I have created car using PS3 controller. Not sure if you already checked that video. Hope it will be helpful. 👍
Hi sir, I'm facing unexpected servo movements eventhough I could control them using analog joystick.what to do sir??What mistake am I doing??
Power issues . Please use good rechargeable battery only . Also check for any loose connection 👍🏻👏🏻
Bro, can you tell me what was the source or the reference paper of that code? Btw , loved
it
Thank you very much for checking out the video👏🏻👍🏻. Actually I was watching some old video of such car and this idea came in mind why not make DIY model of this car using esp32 . That’s why I made this as a hobby project . I am glad you liked it 👍🏻👌🏻
Whats is the range of this rx tx??
I tested it for 80-100 ft. But it’s said that it can go around 200 ft 👍🏻👏🏻
i got a error during complilng i.e. ledcSetup was not declared in the scope. Rectify the error
Please install lower version of esp32 boards which is 2.0.16 👍🏻👏🏻
What component use instead of UBEC... because it's cost is high
You can use any cheap buck converter 👍🏻
@@hashincludeelectronics I also see this kind of schematics without the use of an UBEC. Did you have problems when using the 5V of the Electronic Speed Controller?
Without use joystick and esp32
But what
Using Arduino and sensor with automatic option..
Thanks for checking out video 👍🏻 yeah we can do that too . Good idea 💡
the esp32 not read the joystick values in Transmitter end , Why ??
Please check the video for any missing step . 👏🏻👏🏻
Can I use esp8266 instead of esp32
Thanks for checking out the video 👍🏻. You can use esp8266 but for that you might need to make some changes in code as I have used ESP32Servo library , wifi library . So you need to use corresponding library for esp8266. And also make sure the pins I have used are available on esp8266 else change those pins . Give it a try and I will help you if any issue .
@@hashincludeelectronics ok tq
Wheels didn't rotate when i press the analog joystick.what is the problem between the receiver esp32 and transmit esp32?
Which version of Arduino IDE are you using ?
Arduino IDE 2.3.1
@@na.h5929 ok . There is some small code change in transmitter code so that it will work on this IDE . Change this line as below in transmitter code
esp_now_peer_info_t peerInfo = {};
hashincludeelectrsir another issue...now TT motors are rotating continuously when I give 12V supply??couldn't control it what to do??
Servo motor is rotating automatically and can’t able to control with the joystick.Why?
This can happen if power is not enough . Please check the video for power supply 👍🏻👏🏻
When i press the switch in joystick,the serve rotates 90 degree and when i move the motors ,the servo quickly comes to it's initial position without pressing the joystick switch. Is the anything to modify in code? Or anyother mistake??
May be your switch is getting pressed again while moving joystick .
@@hashincludeelectronicsi couldn't hear any sound of pressing again when i move the joystick,what should i do now??
@@tamilarasan1389 which power supply are you using ? Make sure it’s rechargeable battery and provides more than 3 A current . Power supply interruption can cause esp32 to reset .
12 V and 2A rating@@hashincludeelectronics
@@hashincludeelectronics12V and 2A rating
Hi sir,I have two doubts
1.I'm using Dev module instead of Wrover module ,will there be any changes, if so tell me sir?
2.Is it mandatory to use Wifi101/WifiNINA firmware updater(tools>firmware updater),If so tell me how to set that?
I would suggest to use the same components which I have used in this project . That way you will avoid issues 👍🏻👏🏻
Ok but what about the firmware updater??@@hashincludeelectronics
Help Needed
Sure . What help you need ?
@@hashincludeelectronics in coding
@@TECHAB254 ok
by the way i succes to follow your project in this video, but can you help me... make code for control servos with joystick please🙏
i really need this on my project😭
This project controls servos with joystick
Yeah but not like power steering, if i want to turn left and right like a car
😂😂👏👏👏🇧🇷👏🇧🇷..SHOW
I uploaded the code and it says "error sending the data"
That’s normal . Check if you are receiving data at receiver end .
@@hashincludeelectronics problem solved! thanks a Lot!
@@juanesteban3213 that’s awesome 👏🏻. Good job 👍🏻
sub!
Thank you 👍🏻