Sony TA-4650 V-FET Amplifier (Part 1 - Teardown / Is it Alive?)
ฝัง
- เผยแพร่เมื่อ 25 พ.ค. 2024
- In this video, we do a deep inspection and tear down on a Sony TA-4650 V-FET amplifier and see if it is a viable candidate for a full restoration from the ground up... Will it work?
- วิทยาศาสตร์และเทคโนโลยี
Can't wait for part 2.
Still got one, from 40 years ago!
Almost 50 years now!
I have a ta-5650 that I still have to take a look at. I also have a 4650 that supposedly has been restored but I have never opened it up to check. The amp seems pretty easy to work on. I am always amazed at the lenghts you go to in your restorations. It will be interesting to see what is causing the distortion.
I have a 5650 also in the queue but decided to start with the baby brother 😉 looking forward to see whats waiting for me in the preamp…
As a customer looking to do a full restore on this unit or similar, would need to be really keen. I dare say the cost of the full restore would out way the cost of the unit. I came close to buying the TA-8650 but they wanted the earth. I then looked at the TA-N7B , cost wise is even worse. I ended up buying the ta-3200f power and ta-2000f pre at a fraction of the cost, admit ably not V fets.
You could get away with a few hours work to just do the service bulletins and doing the basics but being VFET, the units are unique and their prices are going up rapidly as unrestored units die and disappear. What the units are worth really comes down to VFET desirability and collectability. Part cost and time is not object for these restores to me :)
I have a ta-8650 and the restoration was HUGE, about a month every day
Yeah to do the job right…. Its a lot of hours
great amp easy to work on
The drop down front faceplate is a nice change for sure!
I have one I found at the thrift store. I'm working on it now. The VFETS are fine.
Be sure to give it a good restoration, need to keep these VFETs going :)
@@whatcouldgowrong7914 For sure. I have a fully restored Yamaha B2 that I found at yard sale.
TA-5650 is the bomb.............wonderful clear sounding amp. Also sold under the Wega badge......... V-4810 only in black.
Encapsulating those diodes with heat shrink and thermal paste almost sounds like what we do with differential inputs
Hello! Could you please share a link to the service bulletin you are referring to in the video? The one that I found doesn't have the info about the necessary resistors' parameters for replacement. I believe they are different for each grade of V-FETs? That's why I would really appreciate you sharing the link! I'm starting restoration of my 4650 and will follow your videos thoroughly. Keep it up and good luck!
There are 2 service bulletins, this is the one for the resistors and bias change. Just take it slow and leave out the vfets until you confirm all the voltages and do the service bulletins. The other bulletin covers testing the VFETs and setting the bias voltage to maximum before reinstalling. Link
www.robuust.nl/~maarten/forum/Sony%20VFET%20bulletin%20[MAE].pdf
@@whatcouldgowrong7914 Thank you very much, I appreciate it! By any chance, do you know if any components should be replaced in the TAN-8550? Or is there a same kind of a note for it? According to my research, it all goes down to replacing the VD1221's and recapping + using the correct resistors to match the grade of V-FETs according to the regular manual. Seems kinda strange to me that 4650 and others have some changes and have to have their resistors replaced for the bigger value and the 8550 seemingly does not.
@@musicscratchpony I don’t have any experience with the 8550 (yet) but im sure some people have experience on audiokarma. General practice for me is to replace any adjustment pots and those double diodes at a bare minimum. But if you want to be really really sure the whole unit should be gone through testing transistors, capacitors etc. It used to just be recapping vintage gear but we’re approaching 50yrs old now and transistors are becoming a big problem also with age. I believe the resistor changes were in relation to the bias change and a design modification. It was just a value change but I generally use higher power resistors because technology has shrunk them drastically
Do you work on these for customers?
resistors go milky
That pot setting is bizarre and a little nuts If " It's clicking so that's fine " what is the point of it ? Potentiometers as I'm sure you know are for finding maximum and minimums or 'peaking' or for setting a precise voltage/current. Just wind the pot all the way to the end to give the maximum voltage is wrong because a piece of wire would be better, unless this works in a very odd way that's nonsense. Trimmers should never be maxed out. Can you explain please ?.......cheers
VFETs are depletion mode devices unlike most transistors which means you want maximum drive voltage on the bias / gate for first power up instead of none. Without high bias voltage, the VFETs will fully conduct and blow themselves up. From this point you then set the bias to 45mV :) the pots are 2.2k which replaced the factory ones. That is why 1-2ohms is normal from source to drain with no power 🙂
@@whatcouldgowrong7914 So this is an initial state and you will back those pots of the endstop at some point ?
@@andymouse Yes in the video it is powered up with the highest gate voltage to stop the VFETs conducting, then I back off the trimpots and eventually the bias starts to climb which you can see in realtime :)
@@whatcouldgowrong7914 Awesome I look forward to that and the amps performance! Thanks for replying :)
These things were big, ugly, stinky, dusty, and I don't miss my massive Sony receiver.
If it ain't broke don't fix it.... 'Stripping boards down because capacitors legs aren't right etc😂
If a VFET amp breaks and the VFETs blow then its over so decide if that risk is worth it lol. You aint fixing these after a failure.