@A person who never keeps mouth shut When u desolder , do u need to use flux ? I need to fix a balls up i did , i bridged to joints... I never knew about flux at the time
True, always use flux. But when soldering THT parts, the flux core inside the solder is enough. Always try to get a good joint without unnecessarily using extra flux and prevent unnecessary cleaning.
For those that are confused: Flux is to be used in two cases. The first is with surface mount devices as it is exceptionally difficult if not impossible to solder a surface mount device to a board with a wire of solder. It is much easier to coat on some flux paste and then attach a little solder to the end of the iron and tap the flux paste. The second time to use flux paste is if your solder wire doesn't have a good amount of flux already in the core of the wire. Sometimes your solder will get spiky when you've corrected it too much and flux helps shape the solder into a desirable shape after you've fucked up too much. Also, in the case of Surface mount devices, you can buy flux paste that has solder in it. There exists specialized ovens for this type of paste with a very exact and precise heating and cooling curve. You basically apply paste to the pads on your board, put your components down and then throw the board in the oven to melt the solder and your done. This helps cut down on the amount of time it takes to place all of your SMDs (you can use a stencil) and solder them all down as well as lowers how god damn tedious that process can be.
So if I'm soldering components to a PCB and my solder has a rosin core, I don't really need to add any flux unless I mess up the join and need to redo it?
flux is a mix of components that is acid, especially under high temperatures, the reason we use it is for removing oxidation so the solder mix can get a clean contact, if you dont use flux there might be a space between inside your connection becouse of the natural oxidation of metals, that can make the contact unstable and might even slip out, thankfully most solder wires come with some ammount of it, so using extra flux is somewhat not needed but its good pratice on some cases
At 370 degrees, everything sticks fine for me. I only use flux when I desolder. If I have a smd/set component, I use solder paste, like you said. A decent adjustable iron makes all the difference in the world.
Solder Type : Solid = Built-in flux inside the lead is not used up yet. Solder Type : Liquid = Because you use heat pre-place the lead as a blob (on solder iron's tip, or place on PCB), the lead had gone through liquid state once. The flux inside had been used and maybe insufficient when you actually join things. At time soldering = At the moment when 2 things you wanna join touch each other. At time soldering, solder : Solid = At the moment when 2 things you wanna join touch each other, you then bring fresh lead into play the last. In this type of soldering, you can use the built-in flux for a while before you need to add more if you are able to make it quick. If you need to adjust things for 2-3 times though, you may need to add more flux.
@@Niyaz916 You probably have a new tip. The first thing you should do with a new tip is put it in the iron, and tightly wrap solder around the tip a few times, put it in the holder, change the heat to high, and plug it in. Wait quite a while. The loops of solder should melt and drip off leaving a nice shiny "seasoned" tip. Then let it cool down (or use it). Always leave that sliver solder residue on your tips. You can wipe off excess blobs with a wet sponge.
As a newbie, THANK YOU SO MUCH!!! I've seen so many soldering tutorials that either say "just use flux" or "there's flux in the solder", but this is the first one I've seen that really shows the effect it has, and this explains many of my frustrations figuring out how to solder.
I've been soldering for decades, even so it was not at all clear to me what point was trying to be made through much of the video. To use flux? Sure, but what point is being made from 1:30 - 2:30? To prove flux evaporates? Is the goal just to get a shiny ball that looks wonderful? And I kept wondering, with all that flux being applied, why didn't the solder wick to the end of the wire? The graphics were truly cryptic. What is meant here by solid solder and liquid solder? Is it all flux-core solder, being applied differently? Where solid = applied from wire to heated joint, and liquid = applied first to soldering iron??? Ok, being critical, but with slightly more effort to explain - IN ENGLISH - it could have been done in 30 seconds, as Michael Noble pointed out. ;>)
I wish I had known this about 20 years ago! I eventually learned the role of flux and why solder did what it does, but it was some hard, frustrating lessons. This explains in a bit over 7 minutes what took me years of on and off experimenting. I'd give up and not touch electronics for months at a time, eventually years at a time, just because I couldn't get good soldering. This is one of the lessons I felt should have been taught to me in school. I even took several college classes in electronics and soldering wasn't even taught. I'm keeping this video handy so I can send it to people who I teach electronics concepts to. It'll be a huge help.
It's crazy ain't it? We had flux in our electronics course, but not a good explanation of what it does and how to use it, clearly demonstrated here in 7 minutes hahhaa
I don't usually like instructional videos with no talking (just music and text) BUT this video helped me clearly understand one of the soldering mistakes I've been making for nearly 40 years. Excellent! The camera angle on the matrix board was very artistic too.
Flux is your best friend! I highly recommend the gel type flux over the liquid pens. The gel gives you more working time and stays in the area you're trying to reflow (until heated, of course). I regularly solder surface mount ARM microprocessors, and have drowned boards in flux when reflowing a component two or three times over. If you think that you've used too much flux, you'll be fine. Impossible to overdo it in my experience. When your components are soldered, ensure that all that extra flux is washed off with 99% isopropyl alcohol or PCB flux remover. Flux can be slightly conductive, with the possibility of causing fine pitch SMD components to function unreliably. 3 minutes of scrubbing with an ESD brush and isopropyl will remove the majority of the remaining flux residue. Soldering can be both very rewarding and very frustrating. If you feel like you're getting impatient/about to put your head through the wall, set the board aside and come back to it with a clear head.
Man, that explains my failure. I burned an esp32, despite double-checking and washing its joints. probably because the flux underneath the element could not be removed and it ordered the MCU to operate on 1.8V instead of the given 3.3V... Thanks for brightening me up :)
"Set the board aside and come back to it with a clear head" this. So many times ive found my self doing a project and having invested hours of work into it and because of my impatience, id end up ruining it. Once I realized that when I start getting frustated to step away, things came out alot better and ended up being a far superior end product.
Such a great demonstration. What I took away from this is that flux aids the transfer of the solder onto whatever surface its being put onto, it evaporates as it is heated and without it it causes the solder to not adhere properly (you can see that with the small tail of solder that sticks up after removing the iron from 2:03 onward) and a telltale sign of not having enough flux on a solder joint is when it is not reflective or when it doesn't flow to fill the size of the pad/lead.
The flux inside the wire is always preferable, in my opinion, since it solidifies instead of living a liquid residue. I always add some flux, but as little as I can, only to improve wetting. Anyway, your excellent video proves the point!
When soldering small stuff with 0.3mm solder wire or smaller external flux is almost required though.. I usually use an alcohol solved liquid flux with a bonpen as applicator, it's usually possible to only put flux on the actual parts so that there is little to none residue at all.. There are of course situations where you might want other kinds of flux but for almost all situations I prefer the alcohol based ones. en.bonkote.co.jp/product/peripherals/bonpen.html
To be honest I really didn't know why I needed Flux because I always added more solder when it started to get a cold joint but thank you so much for taking the time to make this video and I really like that thing you put on the side of the video of how much flux is left that was really cool and help me understand it.
I clicked like 3 times I hope that many beginners will start watching this video. After watching the video, I found out why soldering didn't work well. thank you 😍😍😍
i have built many things over the last 13 years and repaired many more over the last 20. being self taught has its advantages and disadvantages based on the circle your around. today this video has explained a problem i have been asking people and google for years. "How do i get rid of the tips"? I guess my question was to simple and i hadn't done enough research. Thank You very much for this video!!
Hi, just wanted to say I learned a bunch with your video. I could not stop staring at the resin melting and the soldering wire fighting agaisnt each other. Each time you flick the tip and soldering material moves it just reminds me of huge mountain taking different shapes or hyperbolic intersection of a plane forming cones. It is so beautiful. I’ve found my craft!
Flux is magic, even with rosin core solder, I still put just a wee bit on tabs before soldering, it's the difference between mirror like joints and grey blobs. It also keeps it from creeping and bridging gaps it you start first by making a pool of flux, a little electrical cleaner when you are done and it's good to go.
you gave me so much courage over soldering . now i feel very confident on soldering anything. actually i solder lens sensors , camera motherboard, smd stuff. i feel no fear because of you . thank you. 🤗
Another one here who’s been soldering for years and this has just brought so much knowledge to my solder game. Typical approach here was just to balls more solder onto the tip when liquid soldering when I should have been using flux !!
Neither my electronic teacher thought me when & how to use flux 😑😑 But this guy thought me in 7 minutes !!!! Most satisfying video ever !!!! I think u just earned a subscriber
I've learned more from this video than I have from the 5+ hours of other videos out there on TH-cam. I now actually have a decent logical understanding of how things will react and what to do when I don't get the result I want. Thank you.
In other words.. flux is your friend in soldering. I've made a habit to add flux to whatever i solder and works great.. form soldering SMD's to soldering sheetmetal. Actually in sheetmetal soldering is required to use flux as the tin/lead bar does not have any flux in it. - i use borax when soldering big stuf, smd no clean type flux for smd work, and for general wires and connectors i use my blend of rosin/IPA made into a liquidy-gelly type of flux.. a lot of mess afterward but good enough for general splices and connectors.
I’ve soldered so many things in my life. But I’ve never really known why I used flux or if I should use flux. This video answered the question without even talking.
Some don’t believe in using extra flux of any kind. What a duh idea! I can’t press the importance of extra flux use each and every time you solder. The key point in this is to use only the same type flux as the solder’s flux core. It matters not the flux’s state, liquid, gel or paste, what matters is that it matches the flux type, R, RA, RMA or others. There is also the area of starting with clean surfaces of the PCB, leads and wire. Starting clean and finishing clean is what separates the ones who understand the high quality, high reliability soldering. You cannot under evaluate the importance of flux in any case regardless of the level of involvement of your soldering. Flux use is what separates the ones who know and care from the ones who don’t know or care. Learning this importance matters as your project or your job depend on the quality of your work as well as the quantity. Extra flux is what separates the ones who know from the ones who are lost and need guidance to empower them and allow them to improve themselves.
actually the flux is there to prevent oxidation so i'd say it's the exact other way around... flux when you're heating up something and then applying solder (heating up causes oxidation) and no need for flux when you're just applying the solder... i'd probably use it in both cases just to be sure tho
Oxides form in the presence of oxygen, heat not needed (but it helps). The flux is a "reducing agent", not in the "it reduces their formation", but in the Redox sense (check wikipedia for that word). It actually drives off the oxygen, turning oxides into the straight metal again.
Anybody else love the music just as much as the material?!? AWESOME TRACKS this author has. I keep coming back to the vid for the music, even tho i got learned by the flux material.
@@cookedpotato ya. case in point, i just put away my groceries and flux really helped. I'll probably use flux tomorrow also. and next time i solder after watching this use it before during and after soldering. and maybe a few times during. I should buy stock in flux.
Instructions are hard to follow, but this is a VERY Important distinction to make. Molten vs Cold solder at time-of-Soldering. Thankyou for sharing it.
It is mandatory to clean the flux? or only those that are corrosive? because I never heard of them causing any problems with the rosin type (in circuits that handle low frequencies). Rosin type, aka Colophony a natural pine resing. I also heard about fluxing the pcb to protect it. , I don't know... I never did.
Usually says No clean flux if it is ok to just leave it. I think Mikes electric stuff or something like that has a video explaining different types of solder and flux. I rarely remove flux and never seen a issue
+tullgutten hey thank you for sharing knowledge, to be honest I never used real natural colophony, what I used was an "activated" resin that comes in a can like shoe polish, from the brand ThermoPasty "Kalafonia, aktywna do lutowania", to be more specific. Recently I saw a video of "how to make homemade flux" and use it to cover a circuit made in a prototype pcb to protect it from moisture... Well I'm about to do several experiments with high - low frequency, high - low voltage and high - low current to see what happens, greetings
E eu achava besteira em comprar e usar a pasta para solda... Agora vi o quanto eu sofria para soldar e ficar pequeno componentes... Mundo imaginei que iria assistir esse vídeo tão aleatório e que iria me ensinar kkkkk parabéns, e por sinal também satisfatório
This is really eye opening. Flux is magic. I wish this appeared on my soldering tutorial searches. It was only recommended to me now, ~4 months later. But never too late! I still haven't used the flux I have 😁 my solder lead has flux in it, but sometimes my joints get all messed up. So flux is the secret ingredient huh...
![[MV] A leap of faith...ความเชื่อใจครั้งสุดท้าย (From "Petrichor the series")](http://i.ytimg.com/vi/U1piZH2CNXA/mqdefault.jpg)
You've just improved my soldering by 1000%.
1000% of 0 is 0
(It's a joke doe, i was referring to myself, i suck at soldering)
@@NirousPlayers So do I.
@Lazy Buddy 123
Maybe but a good demonstration is always helpful, thats why masters like you are also here...
@A person who never keeps mouth shut When u desolder , do u need to use flux ? I need to fix a balls up i did , i bridged to joints...
I never knew about flux at the time
100% True
when to use flux?
1: Always
2: Always use Flux
3: use Flux already, it doesn't hurt.
What I assumed it would say lol
Thankyou
True, always use flux. But when soldering THT parts, the flux core inside the solder is enough. Always try to get a good joint without unnecessarily using extra flux and prevent unnecessary cleaning.
If you're in doubt, add more flux! 🤣🤣
I just had a hard time soldering corroded wire and wish I had flux, who knows how long it will hold up
For those that are confused:
Flux is to be used in two cases. The first is with surface mount devices as it is exceptionally difficult if not impossible to solder a surface mount device to a board with a wire of solder. It is much easier to coat on some flux paste and then attach a little solder to the end of the iron and tap the flux paste. The second time to use flux paste is if your solder wire doesn't have a good amount of flux already in the core of the wire. Sometimes your solder will get spiky when you've corrected it too much and flux helps shape the solder into a desirable shape after you've fucked up too much.
Also, in the case of Surface mount devices, you can buy flux paste that has solder in it. There exists specialized ovens for this type of paste with a very exact and precise heating and cooling curve. You basically apply paste to the pads on your board, put your components down and then throw the board in the oven to melt the solder and your done. This helps cut down on the amount of time it takes to place all of your SMDs (you can use a stencil) and solder them all down as well as lowers how god damn tedious that process can be.
So if I'm soldering components to a PCB and my solder has a rosin core, I don't really need to add any flux unless I mess up the join and need to redo it?
@@TranquilMarmot correct
flux is a mix of components that is acid, especially under high temperatures, the reason we use it is for removing oxidation so the solder mix can get a clean contact, if you dont use flux there might be a space between inside your connection becouse of the natural oxidation of metals, that can make the contact unstable and might even slip out, thankfully most solder wires come with some ammount of it, so using extra flux is somewhat not needed but its good pratice on some cases
At 370 degrees, everything sticks fine for me.
I only use flux when I desolder.
If I have a smd/set component, I use solder paste, like you said.
A decent adjustable iron makes all the difference in the world.
Solder balls up on iron, then rolls off, and drops to the ground. What ingredients am I missing?
"Solder type when soldering
At time soldering, solder : Solid"
yes I totally understand
right ? WTF does that even mean ?
Solder Type : Solid = Built-in flux inside the lead is not used up yet.
Solder Type : Liquid = Because you use heat pre-place the lead as a blob (on solder iron's tip, or place on PCB), the lead had gone through liquid state once. The flux inside had been used and maybe insufficient when you actually join things.
At time soldering = At the moment when 2 things you wanna join touch each other.
At time soldering, solder : Solid = At the moment when 2 things you wanna join touch each other, you then bring fresh lead into play the last. In this type of soldering, you can use the built-in flux for a while before you need to add more if you are able to make it quick. If you need to adjust things for 2-3 times though, you may need to add more flux.
@@5argon Awesome reply mate, Thank you for your information):
@@5argon what to do if the soldering lead doesn't stick to the tip of soldering iron?
@@Niyaz916 You probably have a new tip. The first thing you should do with a new tip is put it in the iron, and tightly wrap solder around the tip a few times, put it in the holder, change the heat to high, and plug it in. Wait quite a while. The loops of solder should melt and drip off leaving a nice shiny "seasoned" tip. Then let it cool down (or use it). Always leave that sliver solder residue on your tips. You can wipe off excess blobs with a wet sponge.
Q: When to use flux?
A: Yes.
Sums it up perfectly
Yes for over all.
Yes
Lol
Hahahaha
As a newbie, THANK YOU SO MUCH!!! I've seen so many soldering tutorials that either say "just use flux" or "there's flux in the solder", but this is the first one I've seen that really shows the effect it has, and this explains many of my frustrations figuring out how to solder.
Not only is this the best video about flux I've ever seen, it's one of the most clear and concise expressions of knowledge I've ever seen too!
Bravo!
Yeah, the English almost made sense
Concise?! He took 7 minutes to show what could have been done in 30 seconds!
I've been soldering for decades, even so it was not at all clear to me what point was trying to be made through much of the video. To use flux? Sure, but what point is being made from 1:30 - 2:30? To prove flux evaporates? Is the goal just to get a shiny ball that looks wonderful? And I kept wondering, with all that flux being applied, why didn't the solder wick to the end of the wire? The graphics were truly cryptic. What is meant here by solid solder and liquid solder? Is it all flux-core solder, being applied differently? Where solid = applied from wire to heated joint, and liquid = applied first to soldering iron???
Ok, being critical, but with slightly more effort to explain - IN ENGLISH - it could have been done in 30 seconds, as Michael Noble pointed out. ;>)
In All Languages!!!
I wish I had known this about 20 years ago! I eventually learned the role of flux and why solder did what it does, but it was some hard, frustrating lessons. This explains in a bit over 7 minutes what took me years of on and off experimenting. I'd give up and not touch electronics for months at a time, eventually years at a time, just because I couldn't get good soldering. This is one of the lessons I felt should have been taught to me in school. I even took several college classes in electronics and soldering wasn't even taught. I'm keeping this video handy so I can send it to people who I teach electronics concepts to. It'll be a huge help.
Even people with PhDs in electronics don't know how to solder properly.
It's crazy ain't it? We had flux in our electronics course, but not a good explanation of what it does and how to use it, clearly demonstrated here in 7 minutes hahhaa
This is the most wholesome comment I've ever seen on TH-cam. Thank you.
How does flux work? Why does solder stick when there is flux? It almost look like a magnet
+1000 MAN
So that's why my soldering always looks like shit lol. Thank you, amazing video, super satisfying to watch.
Lol, me too
I might go back and fix up my first attempt I did earlier today lol.
I don't usually like instructional videos with no talking (just music and text)
BUT this video helped me clearly understand one of the soldering mistakes I've been making for nearly 40 years.
Excellent!
The camera angle on the matrix board was very artistic too.
edgeeffect damn you old af
Daniel V sadly an adverse effect of life.
not your fault, youtube isn't there at those time
- when to use flux?
+ when ur soldering.
Apparently
I'll also add, when ur desoldering, specially SMD components previously soldered in those-damn-tiny-pads-which-always-end-ripped-from-the-pcb
Flux is your best friend! I highly recommend the gel type flux over the liquid pens. The gel gives you more working time and stays in the area you're trying to reflow (until heated, of course). I regularly solder surface mount ARM microprocessors, and have drowned boards in flux when reflowing a component two or three times over. If you think that you've used too much flux, you'll be fine. Impossible to overdo it in my experience. When your components are soldered, ensure that all that extra flux is washed off with 99% isopropyl alcohol or PCB flux remover. Flux can be slightly conductive, with the possibility of causing fine pitch SMD components to function unreliably. 3 minutes of scrubbing with an ESD brush and isopropyl will remove the majority of the remaining flux residue.
Soldering can be both very rewarding and very frustrating. If you feel like you're getting impatient/about to put your head through the wall, set the board aside and come back to it with a clear head.
Man, that explains my failure. I burned an esp32, despite double-checking and washing its joints. probably because the flux underneath the element could not be removed and it ordered the MCU to operate on 1.8V instead of the given 3.3V...
Thanks for brightening me up :)
@Kappa thanks, that also solved another issue: difficult removing of burnt flux. Another proof for not buying too cheap things.
"Set the board aside and come back to it with a clear head" this. So many times ive found my self doing a project and having invested hours of work into it and because of my impatience, id end up ruining it. Once I realized that when I start getting frustated to step away, things came out alot better and ended up being a far superior end product.
@Kappa does this stuff works with every solder metal type?
Instructions unclear accidentally made computer out of fkux
If someone had made this simple, but perfect, demonstration video 30 years ago my soldering life would have been completely different.
Абалдеть! Шикарное видео. Смотрел в обед на работе, без звука - всё ясно и понятно. Огромное человеческое спасибо за Вашу работу!
Such a great demonstration. What I took away from this is that flux aids the transfer of the solder onto whatever surface its being put onto, it evaporates as it is heated and without it it causes the solder to not adhere properly (you can see that with the small tail of solder that sticks up after removing the iron from 2:03 onward) and a telltale sign of not having enough flux on a solder joint is when it is not reflective or when it doesn't flow to fill the size of the pad/lead.
I have no idea why I'm watching this
S O L D E R P O R N
Same
Yeah what the fuck is this
LeBrick Mayhitslikeafeather soldering, like welding, it’s super entertaining to watch too
Yall shitlords never solderd
The flux inside the wire is always preferable, in my opinion, since it solidifies instead of living a liquid residue. I always add some flux, but as little as I can, only to improve wetting. Anyway, your excellent video proves the point!
Bloguetrónica you can always brush out excess flux with a dental brush and some isopropilyc alcohol to leave it pristine
When soldering small stuff with 0.3mm solder wire or smaller external flux is almost required though.. I usually use an alcohol solved liquid flux with a bonpen as applicator, it's usually possible to only put flux on the actual parts so that there is little to none residue at all.. There are of course situations where you might want other kinds of flux but for almost all situations I prefer the alcohol based ones.
en.bonkote.co.jp/product/peripherals/bonpen.html
Finally, best video about flux ever!!!
True
i agree!!
Same here ! Only noobs ! :))
True
except it never answers the question
To be honest I really didn't know why I needed Flux because I always added more solder when it started to get a cold joint but thank you so much for taking the time to make this video and I really like that thing you put on the side of the video of how much flux is left that was really cool and help me understand it.
Well there is flux in the solder wire so basically you're adding flux
I clicked like 3 times
I hope that many beginners will start watching this video.
After watching the video, I found out why soldering didn't work well.
thank you 😍😍😍
i have built many things over the last 13 years and repaired many more over the last 20. being self taught has its advantages and disadvantages based on the circle your around. today this video has explained a problem i have been asking people and google for years. "How do i get rid of the tips"? I guess my question was to simple and i hadn't done enough research. Thank You very much for this video!!
This was very good information to learn.
Hi, just wanted to say I learned a bunch with your video. I could not stop staring at the resin melting and the soldering wire fighting agaisnt each other. Each time you flick the tip and soldering material moves it just reminds me of huge mountain taking different shapes or hyperbolic intersection of a plane forming cones. It is so beautiful. I’ve found my craft!
Flux is magic, even with rosin core solder, I still put just a wee bit on tabs before soldering, it's the difference between mirror like joints and grey blobs.
It also keeps it from creeping and bridging gaps it you start first by making a pool of flux, a little electrical cleaner when you are done and it's good to go.
you gave me so much courage over soldering . now i feel very confident on soldering anything. actually i solder lens sensors , camera motherboard, smd stuff. i feel no fear because of you . thank you. 🤗
One of the best videos I have ever seen, amazing .... this is how students should be taught
Another one here who’s been soldering for years and this has just brought so much knowledge to my solder game. Typical approach here was just to balls more solder onto the tip when liquid soldering when I should have been using flux !!
I've spent 14 minutes of my life seeing this thing twice.
Simply the best demonstration of why flux cored solder never works for me. Thank you so much.
Neither my electronic teacher thought me when & how to use flux 😑😑
But this guy thought me in 7 minutes !!!!
Most satisfying video ever !!!!
I think u just earned a subscriber
Congratulations! So clear, plus excellent image quality. One of the best how-to on TH-cam!
You've just gained another subscriber.
Awesome 👏🏻. I have been using flux for ages without knowing how cool is that stuff. Until i saw your very well explained video.. 🤦🏻♂️
I've learned more from this video than I have from the 5+ hours of other videos out there on TH-cam. I now actually have a decent logical understanding of how things will react and what to do when I don't get the result I want.
Thank you.
Such a simple and effective video, that flux bar is brilliant! thank you
The most informative videos on soldering I've ever seen. Great job.
In other words.. flux is your friend in soldering. I've made a habit to add flux to whatever i solder and works great.. form soldering SMD's to soldering sheetmetal.
Actually in sheetmetal soldering is required to use flux as the tin/lead bar does not have any flux in it. - i use borax when soldering big stuf, smd no clean type flux for smd work, and for general wires and connectors i use my blend of rosin/IPA made into a liquidy-gelly type of flux.. a lot of mess afterward but good enough for general splices and connectors.
Good example not just of using flux but what proper soldering looks like, and when it can go wrong. Wish i had seen this when i started!!
We definitely need a video about temperatures!
I’ve soldered so many things in my life. But I’ve never really known why I used flux or if I should use flux. This video answered the question without even talking.
1:24 The PERFECT way to show when you need flux. Bravo.
One of the basic need of soldering components, wether they are big or small.
Nice video
At first, it's "why is this on recommended page?", but after watcing this, I've learned something good.
Yep, this is exactly the video I needed. Before, after, and transition between both = perfection.
Thank you!
All my questions were answered in this video. I now know everything there is about soldering.
I learned a very important lesson from you. Thank you for sharing your knowledge for us.
only use demonstration texts and background music, but *very clear and informative*
+1 like and subcribed.
Mini welder
Thank you for the video. Every electrical and computer engineering student should be required to watch this video.
Into laboratory hours of electronic school this was first lesson after security training
Thank you so much for this vid ^^ simple, straight on point and simply explained. love the flux-meter :D
This video helped me understand why I've never had any luck with soldering. Thank you!
Fantastic my friend, thank you for the nothing left to question explanation!👍👍👍
There's something deeply satisfying about watching something being soldered properly.
Some don’t believe in using extra flux of any kind. What a duh idea! I can’t press the importance of extra flux use each and every time you solder. The key point in this is to use only the same type flux as the solder’s flux core. It matters not the flux’s state, liquid, gel or paste, what matters is that it matches the flux type, R, RA, RMA or others. There is also the area of starting with clean surfaces of the PCB, leads and wire. Starting clean and finishing clean is what separates the ones who understand the high quality, high reliability soldering. You cannot under evaluate the importance of flux in any case regardless of the level of involvement of your soldering. Flux use is what separates the ones who know and care from the ones who don’t know or care. Learning this importance matters as your project or your job depend on the quality of your work as well as the quantity. Extra flux is what separates the ones who know from the ones who are lost and need guidance to empower them and allow them to improve themselves.
oooo now i get it why people use flux when soldering microprocessor.... thanks for ur video
Great instructional video. Appreciate the simple, straightforward diagram at the end.
i use cheap flux core solder, my connections are always perfect and it saves a lot of time.
I only see your soldering videos because it's soo satisfying to watch 🥰
actually the flux is there to prevent oxidation so i'd say it's the exact other way around... flux when you're heating up something and then applying solder (heating up causes oxidation) and no need for flux when you're just applying the solder... i'd probably use it in both cases just to be sure tho
Oxides form in the presence of oxygen, heat not needed (but it helps). The flux is a "reducing agent", not in the "it reduces their formation", but in the Redox sense (check wikipedia for that word). It actually drives off the oxygen, turning oxides into the straight metal again.
What a brilliant video.. Informative, concise, and imminently relaxing. Well done!
*Thank you for this very amazing and educational video...Keep up the good work!*
You have some of the best soldering videos on TH-cam
nice ! i do not speak english but i understand yours videos
Been soldering for car projects for yrs and i just learned about flux.. thank you so much for this video
I got this on my recommended and I have no idea what’s happening
Yeah same...
Guess i habe to learn about soldering now
Anybody else love the music just as much as the material?!? AWESOME TRACKS this author has. I keep coming back to the vid for the music, even tho i got learned by the flux material.
2:28 relax 😌
Free Videos 👍😊
I Finally understand why I always see people applying that compound! Thanks for the video! It explains why my solders are totally shitty 😭
"When not to use flux" would be a more informative video... although I am not sure the video will be very long.
I can not FATHOM just HOW MUCH this video is gonna help me in the future!!
I guess I need to buy some flux.
yes. even if you don't plan on soldering.
@@surveyguyor8958 lol yes I totally agree it would help alot in the future
But fun fact petroleum jelly can be used as flux,
@@cookedpotato ya. case in point, i just put away my groceries and flux really helped. I'll probably use flux tomorrow also. and next time i solder after watching this use it before during and after soldering. and maybe a few times during. I should buy stock in flux.
So we should apply flux after soldering and then provide it heat?
Look at your join. If the flux has been used up, add a bit more flux.
This video answered some questions I didn't know how to ask. This was extremely helpful, thank you!
The answer... Always!
Instructions are hard to follow, but this is a VERY Important distinction to make. Molten vs Cold solder at time-of-Soldering.
Thankyou for sharing it.
It is mandatory to clean the flux? or only those that are corrosive? because I never heard of them causing any problems with the rosin type (in circuits that handle low frequencies). Rosin type, aka Colophony a natural pine resing.
I also heard about fluxing the pcb to protect it. , I don't know... I never did.
Usually says No clean flux if it is ok to just leave it.
I think Mikes electric stuff or something like that has a video explaining different types of solder and flux.
I rarely remove flux and never seen a issue
Organic flux MUST be cleaned after what i remember
+tullgutten hey thank you for sharing knowledge, to be honest I never used real natural colophony, what I used was an "activated" resin that comes in a can like shoe polish, from the brand ThermoPasty "Kalafonia, aktywna do lutowania", to be more specific. Recently I saw a video of "how to make homemade flux" and use it to cover a circuit made in a prototype pcb to protect it from moisture... Well I'm about to do several experiments with high - low frequency, high - low voltage and high - low current to see what happens, greetings
Finally, best video about flux ever
5:47 *cringes in extreme discomfort
6:00 *That's better*
One of the best soldering tutorials on youtube, thanks !
Satisfying vid
this was the best explanation I've ever seen. great work!
What does “1~3 soldering” and “>3 soldering” mean..?
soldering or repeat soldering 3 times (3:52), ">3" mean greater 3 times soldering
@@johnerin2291
I was wondering the same thing. Thanks so much for the explanation!
I took ">3" to mean soldering 3 or more adjacent joints, i.e. - "goober flux once, solder many."
E eu achava besteira em comprar e usar a pasta para solda... Agora vi o quanto eu sofria para soldar e ficar pequeno componentes... Mundo imaginei que iria assistir esse vídeo tão aleatório e que iria me ensinar kkkkk parabéns, e por sinal também satisfatório
I always flux up my joints.
This is really eye opening. Flux is magic. I wish this appeared on my soldering tutorial searches. It was only recommended to me now, ~4 months later. But never too late! I still haven't used the flux I have 😁 my solder lead has flux in it, but sometimes my joints get all messed up. So flux is the secret ingredient huh...
And what of the Flux Capacitor?
Also make sure to clean your solder joints after using flux.
How?
@@jjjsmith2497 Isopropyl Alcohol and a clean brush. Then dry it with a q tip or cotton ball.
@@Daa253
Thank you very much.
My soldering has sucked for years and now i know why, lol.
teacher.which tin, you use for these jobs
Thank you for your brief and multiexpanatory videos.. I really appreciate your way of providing the facts under exact examples..
you got a new subscriber haha
thanks
Thanks a lot, i was asking myself too many questions that why my solder wire dry so quickly before the parts even bond. That was helpful🙌🙌🙌
I'm here because I'm preparing for changing my shitty logitech mouse switch
What logitech mouse?
@@MirelRC g102 the switch is omron china 10m click switch, i heard that logitech fix the issue in new mouse they replace it with 20m click switch
@@wolframazer what version is with the 20m switch? G203? I am asking because I have bought last year a g203. Until now it still works.
@@MirelRC omron d2fc-f-7n
Really love the visual demonstrations, keep up the good work :)
what was the video i like it very much thank you so much that i thing that only that why thhe solder is happen like these
finally i get what flux is for!!!!! brilliant demo, have been using flux free solder and messing up with the clingy bits driving me bonkers👍😎🇬🇧😁😁😁
Cool!
This is the best video about FLUX !!!!
PERIOD ....
Wow this made me understand the use of flux so much better. THANK YOU!!!
why are these videos so satisfying to watch??
Even with flux core solder I still like to use a little paste flux. It just makes things flow so much better.
Nice demonstration. Now I can see what happens where there's too little flux.
Very useful tip. Did not know there were so many considerations. Thanks for the advice.