ive got a series 99 panic/crush with a 7500 mortise casset and 996 trim. Does the cylinder just rotate out of the trim after the set screws are losened? It seemed the cylinder was holding the trim on. I dont think I actually have a hole/screw where you did to remove the cylinder.
If everything is lined up correctly on a mortise panic then yes once you loosen the cylinder set screw in the cassette then the cylinder should just spin out.
I have a question about the little metal piece on the back end of the crash bar under the plate on right side when u turn the key it moves the mechanism to allow the door to open it keeps going limp everytime i tighten it down u know an easy fix? Or what do i do in this case?? Please help if u can!! Thank.you
Ok have a Q? Is that not a KNOX BOX on the Latch Side of the door. Where's the FD key to that box. Then you have a service key to that door. Because that's a FD CONNECTION & Fire Sprinkler System. Now that you've changed that lock the FD can't get access to the sprinkler system.
Why not have used a bypass driver? Or broken the pin and unscrewed the cylinder? Drilling is my last resort after I’ve failed picking, bypassing and sheering the pin on the side
Attention new guys...be careful using drills or drivers with door hardware. It is very easy to strip or cross thread these screws. I have been doing commercial door hardware for years and I still always use just a screwdriver on most screws especially those in the trim.
Am a carpenter myself at Qatar NFE project,I work on this locks mostly...
I will be very grateful working with you Daddy
The product is similar to our F8000 series, your explaination is very good!
Very very good video. You are a professional I would trust.
You are so good person so good 👍#udayadewvlog
Very nice. Thanks for the tutorial.
Thanks 🙏 God bless 🙏so good 👍#udayadewvlog
Two pliers and thats it! Man you just saved my life!
A pair of side cutters or lineman pliers work faster in my opinion.
Thanks man! I was able to fix a loose rim cylinder and save a locksmith call out.
Very very good video. can you tell me what model panic device , the model out side handle it is thanks
Awesome video! Keep up the good work
Wow thanx really straightforward video Thanx
Well explained and demonstrated.
I’m surprised hardly anyone uses hand held screw drivers anymore. I must be getting old 🙄
Nice 👍#udayadewvlog
Where is the best place to buy the rim cylinder, and is there a standard size or pin number you should go with?
ive got a series 99 panic/crush with a 7500 mortise casset and 996 trim. Does the cylinder just rotate out of the trim after the set screws are losened? It seemed the cylinder was holding the trim on. I dont think I actually have a hole/screw where you did to remove the cylinder.
If everything is lined up correctly on a mortise panic then yes once you loosen the cylinder set screw in the cassette then the cylinder should just spin out.
Great video. Thank u!
Thanks great video
What if my door has a vertical locking rod and I need to replace the tumbler?
I have a question about the little metal piece on the back end of the crash bar under the plate on right side when u turn the key it moves the mechanism to allow the door to open it keeps going limp everytime i tighten it down u know an easy fix? Or what do i do in this case?? Please help if u can!! Thank.you
Yuyyu y yuyyyyuyu I u y u u
You’ll need to order a replacement dogging kit. They’re made of plastic or nylon, and tend to wear down over time. A common problem.
Thanks good and useful
Ok have a Q? Is that not a KNOX BOX on the Latch Side of the door. Where's the FD key to that box. Then you have a service key to that door. Because that's a FD CONNECTION & Fire Sprinkler System.
Now that you've changed that lock the FD can't get access to the sprinkler system.
Great question. Seems important.
Why not have used a bypass driver? Or broken the pin and unscrewed the cylinder?
Drilling is my last resort after I’ve failed picking, bypassing and sheering the pin on the side
Took this guy seriously until I saw the ryobi
Jk thanks for the video
and that job you can charge like 400 dollars lol
Attention new guys...be careful using drills or drivers with door hardware. It is very easy to strip or cross thread these screws. I have been doing commercial door hardware for years and I still always use just a screwdriver on most screws especially those in the trim.
so good 👍#udayadewvlog
Great advice 😊
Wooo
I will never understand the use of a panic bar inside a riser room. Ridiculous