Caesar…I have seen many of your videos and I appreciate all you do to help us !! Wife and I both have mini’s and love riding together and doing upgrades. Your videos are very helpful!
I was watching a guy work on his bike in a different Vlog last week and he had a rope hanging from the ceiling of his garage that he wrapped around his handlebars just in case his bike wanted to tip over. It was pretty simple and genius. And there's nothing wrong with Abba😊👍
with a small Excel file, this is about what it shows. Where you were at 67 MPH it should now sit at 70.8 or so. Moving all that water around will slow the bike down. It will be faster when it is dry out but again your red line may be a limit. Now upping one tooth up front as well, if 14 going to 15 tooth, the speed would go from 70.8 to 75.8 at 9,000 RPM. also over stock at 50 MPH where you were at 6,700 RPM you would now go to 5,900 RPM.
Ceasar, Video was great. Especially the part where the bike fell. I'm glad you didn't cut that part out. Happens to all us wrenchers and we learn from each other. Have 2 questions. 1. Did you get the sprocket from Lifan or ? 2. What GoPro mount are you using on your helmet. Works great. Keep it up and be safe.
Its a early grom sprocket. I measured and its the same as the groms. So pretty much anyone you buy for the early groms will work. Haven't tried or measured the new groms.As for the gopro mount its stock parts , I just 3d printed a 2.5 inch arm to get it all the way to the front. Message me in the Discord if need specifics.
I’m looking to gain speed and power with little effect on fuel economy. I was thinking of changing out the carb and sprockets. What would you recommend for my 2022 Kifan KP mini 150
Can you tell me? Can we adjust the suspension on these bike at all front and or back? I'm def gonna get the smaller rear sprocket . Can you advice me where to order one. I just bought a 2nd hand ko 150, 2022 Thx Jimi ital
@ Smallenginevelocity>No one gives the sizes of the center and bolt spacing, I ordered a 2inch 40T for my Lifan KPR 200 and it was too small. Can you help tell me the size I need with a 40 T
Going up one tooth in the front will give you more bang for your buck. Normally one front tooth is equivalent to 3 teeth on the rear. May be a little different on these. Front are cheaper and easier to install on these though.
Do you have to loosen or take off the front sprocket in order to take off the chain? I'm going to replace my chain and wasn't sure if that was required.
No just loosen the rear axel and the tire will slide up and give you slack to instal what you need. Be sure to read up on how to align the rear wheel when you put it back together.
@@SmallEngineVelocity if I have a chain breaking tool, I shouldn't have to mess around too much with the sprocket or at all right? I'm getting a Niche Gold chain 428 x ring. It comes with a master link which has a clip for quick connect like the DID chain so it looks to be an easy install. Maybe I'm just over thinking it as I'm not replacing any sprockets.
I meant I shouldn't have to loosen the rear axle to give the chain slack if Im going to break the chain. Every video I saw shows the guy loosening the front sprocket and that just confuses me. I'm sure the chain will come off without any loosening of the sprocket. I watched a grom chain replacement video and it seems to confirm this..
Forget about the fact that for less than the cost of one lever, you could have used a motorcycle stand and not dropped your bike but it looks like you are changing lanes using your mirrors and without turning your head twice.. (Once to see if it is clear and a second while you change lanes). You should really stop and learn how to do the basics before you get yourself hurt.
Caesar…I have seen many of your videos and I appreciate all you do to help us !!
Wife and I both have mini’s and love riding together and doing upgrades. Your videos are very helpful!
I was watching a guy work on his bike in a different Vlog last week and he had a rope hanging from the ceiling of his garage that he wrapped around his handlebars just in case his bike wanted to tip over. It was pretty simple and genius. And there's nothing wrong with Abba😊👍
Hmm I need to do this because I have to replace my triple tree ....
@@SmallEngineVelocity I'm thinking about getting one of these. Do you still have it and do you recommend? Keep up the great work!
with a small Excel file, this is about what it shows. Where you were at 67 MPH it should now sit at 70.8 or so. Moving all that water around will slow the bike down. It will be faster when it is dry out but again your red line may be a limit. Now upping one tooth up front as well, if 14 going to 15 tooth, the speed would go from 70.8 to 75.8 at 9,000 RPM. also over stock at 50 MPH where you were at 6,700 RPM you would now go to 5,900 RPM.
TANWare so for maximum speed you recommend a 35t & 15t in front or what would you go with?
YOU INSPIRED ME 2 BUY ME ONE.....SAVING UP AS WE SPEAK...THANKS FOR ALL YOUR VIDEOS..VERY HEPLFUL..
Great to hear!
I'm digging that jacket. #safetyfirst
Ceasar, Video was great. Especially the part where the bike fell. I'm glad you didn't cut that part out. Happens to all us wrenchers and we learn from each other. Have 2 questions. 1. Did you get the sprocket from Lifan or ? 2. What GoPro mount are you using on your helmet. Works great. Keep it up and be safe.
Its a early grom sprocket. I measured and its the same as the groms. So pretty much anyone you buy for the early groms will work. Haven't tried or measured the new groms.As for the gopro mount its stock parts , I just 3d printed a 2.5 inch arm to get it all the way to the front. Message me in the Discord if need specifics.
i am gonna stick with getting a kpr200
I like your helper
Joe SALADINO my cat helper who gets into everything!
I'm having such a difficult time getting the wheel back on. It's so frustrating lol
I’m looking to gain speed and power with little effect on fuel economy.
I was thinking of changing out the carb and sprockets.
What would you recommend for my 2022 Kifan KP mini 150
Got a link for the 35tooth sprocket
Can you tell me? Can we adjust the suspension on these bike at all front and or back? I'm def gonna get the smaller rear sprocket . Can you advice me where to order one. I just bought a 2nd hand ko 150, 2022
Thx
Jimi ital
@ Smallenginevelocity>No one gives the sizes of the center and bolt spacing, I ordered a 2inch 40T for my Lifan KPR 200 and it was too small. Can you help tell me the size I need with a 40 T
So would you suggest going Down 1 tooth in rear, or Up 1 tooth in the front ( just for a little bit more top speed) ?
Going up one tooth in the front will give you more bang for your buck. Normally one front tooth is equivalent to 3 teeth on the rear. May be a little different on these. Front are cheaper and easier to install on these though.
Do u have a link to where u got the sprocket. Or website by chance. Just want to make sure I order the right size and mount holes
Hey I was wondering where you got all the Lifan stickers etc.? I have been looking everywhere and cant really find much of anything lol...
Do you have to loosen or take off the front sprocket in order to take off the chain? I'm going to replace my chain and wasn't sure if that was required.
No just loosen the rear axel and the tire will slide up and give you slack to instal what you need. Be sure to read up on how to align the rear wheel when you put it back together.
@@SmallEngineVelocity if I have a chain breaking tool, I shouldn't have to mess around too much with the sprocket or at all right? I'm getting a Niche Gold chain 428 x ring. It comes with a master link which has a clip for quick connect like the DID chain so it looks to be an easy install. Maybe I'm just over thinking it as I'm not replacing any sprockets.
I meant I shouldn't have to loosen the rear axle to give the chain slack if Im going to break the chain. Every video I saw shows the guy loosening the front sprocket and that just confuses me. I'm sure the chain will come off without any loosening of the sprocket. I watched a grom chain replacement video and it seems to confirm this..
What size is the chain and sprocket teeth size are they 428 or 420?
428
Is that rear 76mm & is the front 20mm
What size chain is on the kp mini?
I have been wondering the same thing.
I take it you got a new go pro?
Joe SALADINO makes just my old GP3 and my old GP Session
4 minutes into the video I need to replace the peice u screwed that spoke onto whats it called
Makes sense
Forget about the fact that for less than the cost of one lever, you could have used a motorcycle stand and not dropped your bike but it looks like you are changing lanes using your mirrors and without turning your head twice.. (Once to see if it is clear and a second while you change lanes). You should really stop and learn how to do the basics before you get yourself hurt.
Yea that was over 2-3 years ago. I’ve fell and learned. Everyone always see how it should have been done from a video. Thanks for the input