JBL Flip 3 Battery Replacement
ฝัง
- เผยแพร่เมื่อ 18 ม.ค. 2019
- Fixing JBL Flip3 dead battery.
Buy tools: ali.pub/4spc54
Buy JBL Flip5: alii.pub/5mmvrd
I bought a new Cameron Sino 3000mAh Battery GSP872693 here: ali.pub/31o0pw
Tested capacity 3092 mAh.
High temperature adhesive tape used in this video: ali.pub/4wmm4m
Navajo Night by Audionautix is licensed under a Creative Commons Attribution license (creativecommons.org/licenses/...)
Artist: audionautix.com/ - วิทยาศาสตร์และเทคโนโลยี
I used this guide to replace my battery, thanks!
Make sure you have the perfect Phillips screwdriver for the job. You will easily wreck these delicate little screws. Also - some of them are pointy and others are square. Make note of which goes where. I didn't have any fancy silicone or glue to close the hole above the battery. I don't think it makes any difference.
Good luck.
And to JBL: You could build it so the battery is a lot easier to replace. There's no planet B you know.
The silicone or glue is there in order to eliminate any vibration, in time you may hear the battery knocking about. The silicone on the wires and hole to the battery is a good precaution to prevent moisture causing corrosion, it will extend the life of your speaker, ain't nothing fancy about silicone, cheap at any hardware store.
Awesome. It was pretty easy to replace the battery following your instructions
Thanks for the video. It gave me the confidence to order a replacement battery rather than buy a new system. I was able to follow these instructions and take everything apart very easily. My battery was very swollen so it’s no wonder I was having problems. Cheers
Hey Spencer Jose how did you remove the glue and the black tar to be able to unplug the battery from the circuit? I just opened mine and same issue as yours
Mr. Moreno I just picked it with needle nose pliers and a flathead screwdriver if I remember correctly. Don’t have to be overly careful seeing as the battery is no good and the silicone has to be replaced.
Music sounded like he's trying to disarm a bomb! Nice!
😂😂
Lithium Polymer (Li-Po) batteries do not like to be stored at full or empty charge for extended time, if not using any electronic device for extended time try to store them at 50% charge (storage voltage) and the Li-Po will last much longer..
9999jin0
And how to charge it for longer battery health, full charge and full discharge is this damage the speaker
Thank you very much! This helped me fix my JBL flip 3!
Thanks so much for this video... I wouldn't be able to replace the battery without this clear guide. Now my jbl flip3 is as good as new with just merely a fraction of the cost instead of buying a new one.
Thanks so much for this video
Hey, where did u get the battery from and how is it working now?
Perfeito o vídeo explicativo. Bem didático e, inclusive me deu forças para solicitar pela Internet a bateria para reposição. A questão do silicone, eu entendo que seria para não ocorrer vibrações. Vale a pena realizar essa mão de obra. É uma terapia ocupacional e, quando o produto é seu, você mesmo o fará com mais carinho. Uma dica: dobrar uma toalha para servir de apoio! Em se tratando de uma JBL vale o investimento e dedicação, afinal a qualidade dessa caixinha étudo de bom! Abraço!
I used a butter knife to get my cover off haha. Thanks for the fantastic video - I have a new life for my speaker!
Too bad mine had the plastic soldered through and through. The cable was melded on the plastic and the substitution was impossible, unless I drilled a hole in the hard plastic. Lasted almost 4 years but really bummed I couldn't change the battery (swollen). Never mind, I managed to remove the battery without problems, the black plastic made it look like it was a single slab of hard plastic, instead it was the "silicone". Ordered a new battery from amazon, will update if it works as intended :D
Battery arrived, followed the guide and it works! Will update on the quality of the battery but I hope I'll manage another coupla years of usage. The sound quality is very good for its size.
Спасибо, видео довольно качественное. Приятно смотреть. Удачи
Thank you! Mine was doing some weird stuff and figured it was battery. Made it very easy to replace the battery!
from where did u order?
Thanks! I managed to change my battery (almost) effortlessly!
Parabéns pelo seu belo trabalho 👏👏👏👏👏👏
Avery nice and detailed fix, Thanks!!!
Congratulations! Nice video
I haven't tried this replacement yet, but from all I've read many people do not have the skills or tools, or patience. Don't use the cheap tools that come with some of these replacement batteries, they're junk. Get some quality precision screwdrivers, a phone repair set is ideal.
You have to carefully think through each step. Never use force, glue can be broken down with heat, but on this speaker, I wouldn't advise it. Slowly breaking the glue seal with a painter's putty knife is ideal. The smartest thing to do would be to sharpen the end and heat it and slowly work it down the side of the battery till it comes free.
He does quite well in this breakdown, but I would advise taking the flat ribbon cable off before removing the battery, if he slipped or if the battery suddenly came loose he could have easily ripped the ribbon cable.
Be very gentle with the ribbon cable and especially the plug and connector, lift the plastic locking tab before pulling on it. Ribbon cables are very fragile.
Thanks a Million
Very clear and i was able to follow and accomplish :)
@GloGang Saint It will only get worse. Eventually, you will.
worked for me, very useful - thanks!
Good video. My batteri was very swollen and impossible to pull out. Had to drill (non pointy hss drill to not damage battery) a 6mm hole to the other end of the battery compartment which could be accessed from the other end of the unit and push it out with an allen wrench like I noticed someone do on a newer model with better access. Got the job done in case someone struggles with the same issue
Sounds good; I could not find a proper place to dril with the flip 3..
@@rzelissen In mine if I remember accuratly there was a screw with a washer in it which I removed and behind it an there was an incline that ended behind the bottom of the batteri compartment which is big enough to fit a drill bit.
Was not expecting the base was using earbuds and caught me off guard! Great video tho
Thank you very much , Your video is awesome.👍👍👍
Thanks! - worked like a charm 😊
Спасибо, поменял четко по инструкции!
the soundtrack is quite surprising and mermerizing
Dankeschön für die Anleitung. Bei meinem Flip3 waren allerdings der Akku und die Kabel alle eingeklebt und nicht mehr zu lösen. Ärgerlich,aber nach fast 10 Jahren geht das Teil nun in den Elektroschrott! JBL?? Nie mehr, habe mir nun BOSE gekauft! 👍🏻👍🏻👍🏻
Thank you sooooo much. I was able to replace the battery and enjoy my JBL again.
my charging port is almos borken too. any chances??
Anyone know where I can get replacement ribbon cables...the 2 shown at the 2 minute mark.
чуть не выбросил колонку:) спасибо за видео
Excellent! I did it!
Cool dude!! Pretty easy fix! Thx 👌
👍
donde compraste la batería, no la puedo pillar
Do you know if it would solve a scream sound? My speaker does a very loud sound and then juts shuts down. The sounds is almost as someone screaming or scratching something.
Flip with dead battery should work normally with charger connected.
Konstantin Sachkov My flip3 battery doesn’t get charged.. and it doesn’t switch on with connecting charger as well.. any idea what could be wrong??
Que tipo de cita es ??
Did the replacement of the battery make anyone's speaker stop having that screeching noise??
Also wondering this
Just found out that when my flip 3 is charging the screeching noise doesn't occur but when it's not it happens
Por aquaso o senhor trabalhar como o conserto de caixa de som jbl
Excelente cambio solo que es algo de silicón el que ocupa algo que va a batallar para quitar en otro posible cambio de batería 😃
Thank you!
Got a flip 3.. if it wont fully charge - 5th light stays flashing during charging - is the battery bad? Great video & thank you
It's ok. Flip3 leds are crazy a bit.
@@KonstantinSachkov ok thank you 🤓
It looks like you used double sided tape. Is it a special kind of tape or can you use any double sided tape??? Also can you use the silicon to glue the battery down instead of the double sided tape?
You can use any. It's better to use tape (buy in automobile shop) than silicone.
Есть какие-то отличия по батареям в зависимости от парт-номера ? или важна только модель аккумулятора ? иными слвоами если покупной аккумулятор отличается только парт-номером, но не моделью подойдет или нет или нужно чтобы парт-номер аккуумулятора и модель совпадали 100% или не обязательно - чтобы подошел по размерам, вольтажу, распиновке коннектора и т.д ? И подойдет ли аккумулятор от Flip 4 для Flip 3 ?
Есть отличия в зависимости от производителя, в качестве и сроке службы батареи. Батарея подойдёт только от flip3.
@@KonstantinSachkov а если коннектор перепаять , как я понял разница в батереяхля флип3/4 в порядке проводов к коннектору ? т.е взять батарею для 4, и припаять колодку для флип3 поставив правильно провода, или просто перевоткнув в сам разъём, вроде бы провода оттуда можно достать аккуратно.
Thank you for your vid ! I have 2 questions : what size of tape did you use ? And I have seen on other videos that the battery is often glued, did you not have the problem ?
And what are the white and the black sort of tape you use ^^ ?
High temperature adhesive tape (yellow) is 15 mm size, link in description. And any thin double side adhesive from local shop.
@ black tape was originally sealed.
Is this the solution for when the Flip 3 suddenly starts “screaming” even though it is fully charged? I’ve used it only very occasionally for about five years, and I’m wondering if this loud, ugly noise that I’m hearing after running it for only about an hour now is a battery issue.
Possibly it is a battery. Original battery can't live so long 😁
es un pegamento lo que se le pone en los cables de la bateria? Que roducto es?
Silicon
You are pro!! 😎
Thanks for video
strange, I don't know if I have the same JBL Flip 3, but after opening the outer shell, I can't find the three screws to open further. In the parts where the screws should be I only have plastic. Will try to open it up further anyway.
Turns out, I had another model. In my model I had to get the outer speakers out and try to slide the battery out, which turned out to be impossible due to the amount of glue they put. Ended up tossing my JBL Flip 3.
@@ryuuzaki24 it's another version (old one). Try using alcohol and heat air gun, it's possible 😉
Thanks! Ok, I will try again, let's see
Same here. What a lousy production process... there is glue everywhere!
Onde faz isso aqui no RJ (Brasil) ?
mano, essa porra de caixinha tá custando 200 conto, e a bateria no mercado livre também. bagulho perdeu o valor violentamente, e uma pena que a flip 4 tá custando 800 reais. tava procurando aqui pra ver de fazer esse procedimento na minha caixinha tb, mas agora to pensando é em comprar uma nova. abração meu caro!
Adónde puedo comprar la batería
Thx i changed my Battery in 20min but maybe should show all the screws which need to be removed there are a lot more than someone expect of this Video.
Yeah more than 10 screws, then again once you get "the lay of the land" you're able to manage. Unlike some devices that got different screws for different parts of the device...
thank you for video
If the new battery already has the wire on it why didn't he just clip the old one off instead of working to force it through a little hole
Because then you have to put it back
You have to open that rubberized hole because the new harness wont pass through without removing it.
Has anyone done this to fix a squeaky playback? My battery on this model will say fully charged but then playback is terrible, becomes squeaky and sounds like nails on a chalk board. Then it automatically turns off. Would it be worth just trying to change the battery, or will I need a new speaker?
Change the battery.
Is it compulsory to change the battery 🙁
bravo 👏👏
No you F%&*ing B€$@
Thanks!!
Can you replace the old batterie with a new one that has more power.?
More power? Do you mean external battery? You can connect any USB power bank.
İ think he means more mah in the battery
@@proxyhx2075 yes
@@KonstantinSachkov I mean more mAh
@@qurex1808 it's not possible. All lion batteries have almost the same capacity/size ratio. Big numbers that you can find on many cheap batteries just a fantasy of marketing.
Is it hard to take off the grill, and can it be damaged by taking it off?
Use a spudger like he did. You'll have to exercise some traction but it's pretty sturdy (the Jbl plastic, that is), try to use a flat surface so as to minimize the dents.
@@azmodanpc thanks for the help, but i got it off ages ago
@@benthorney5080 No prob, every time I try to open one of these devices I fear breaking everything. If the plastic is not too used and old, it's pretty elastic and sturdy.
Frse and good work
Why does the audio sound like it was recorded inside a human?
What is the yellow clear tape he uses on the battery?
Polyimide High Temperature Adhesive Insulation Tape, it's a bit better than usual clear tape.
ขอบคุณครับ
This is crazy to get to the battery. I don't think I will be doing this
It’s really easy, I did it with this video
Mybe can find some mobile batery with much amp Like 4000mah or higher,Ford many cash ,yust must size be same, sorry for my bad English
Si lo ubiera visto antes no rompía el flex tratando de arrancar la bateria
Why we need to put the high temp adhesive tape on the battery?
To make it looks perfect 😀
What silicone did you used? Universal?
Yes
How do I fix mine it doesn’t turn on it only turns on when I plug it in
Change battery as in video
Hey i have a flip 3 and my problem is it always tuns off after 1or 2 songs. Do i need to change my battery ?
Yes
@@KonstantinSachkov I have a flip 3 and the problem is JBL is not getting charged only charging indication blinking , ports are fine do I need to replace the battery or there can be a problem with charging port.
@@rvmec081 replace the battery
Is it hard to put grill back on and take it off
No, with the right tool and patience it's a cinch.
хорошее видео, герметика много
What's the silicone for?
To keep it waterproof.
vu le paquet de neoprène ,je pense qu'il ne cpt plus jamais changer sa batterie..je ne comprend pas non plus pourquoi tant se schotch
and What is that clear paste you putted on the cables ?
Silicone
@@KonstantinSachkov how we know the battery is the problem?? can you explain please ?
@@johnnytallo it doesn't work more than 1-2 hours after charging.
@@KonstantinSachkov thank you dear
A special type of silicone or not a specific silicone?
Thanks.
What is the silicone for? Is it necessary?
To save waterproofing
Soundtrack - Очень впечатляет... Похоже из интерстеллара)
how we know the battery is the problem?? can you explain please ?
It will go from a full charge (five lights on) to two or less very quickly, within minutes.
What kind of tape is used at 5:25 mark?
ali.pub/4wmm4m
What about the charger port how would you replace that
It's easy to replace, but it'd be hard to find a new socket. It might be easier to install some usb-c socket from phone, you can find many different types on AliExpress.
@@KonstantinSachkov OK thanks
Can I put a flip 5 battery in instead for better life
You have to check the voltage to make sure it's the same and make sure it will fit but could be possible!
Подскажите, аккумуляторы на Flip3 и Flip4 подходят друг к другу?
Думаю что нет, слышал, что разъем разный.
@@KonstantinSachkov понял, спасибо
What song is being used?
Navajo Night by Audionautix
Спасибо за видео
Where should I get battery for flip 3.
Look at description
Where will I get the new battery
Link in description
Я свой заменил, спасибо!
der dekt auch nicht nach das sind die sachen die eaby laden und man bekomt nix mher auseinder
where to buy the battery?
Link in description
My 1 speaker of jbl flip 3 sound bur bur how to clear dis also needs battery to be replaced???
If it works without charger short time, you should replace battery.
@@KonstantinSachkov how much money spend for battery🔋
Please tell me my whatsup number 7020666234
@@amitkashte5673 $18, link in description
How to I collect tha battery Can you give me address?
Link in description
Where can we find the battery?
Link in description
how about flip 5
Why would you have to replace a battery?
Old one was completely dead, charge was enough just for a minute. And it swelled very much, only power button worked. The first Flip3 did the same after 10 months, so I replaced it. This one broken after 1.5 year.
@@KonstantinSachkov thanks. I did not know the battery would do that.
Mine is about 2 yrs old and only holds a 1 hr charge. Wonder how much a new battery is.
@@wadep9916 link in description.
@@KonstantinSachkov if you replace the the battery would it still be water resistant after
Pin mua ở đâu vậy bạn
Link in description.
nice.
Why apply silicone?
To make it waterproof again
I assumed it has to do with the bass passive radiators performance
Подход! ☝
What kind of silicon was it sorry brother
Anyone from Plumbing Supply Store
@@KonstantinSachkov thanks copy that
👏