Amazing video, and nice looking kit! What would have been nice to see is a before and after with a rider sitting showing us the difference in the foot and leg position. Can't seem to find these kits on your website, though, can you provide a link please?
My kit doesn't have the M8 bolts and nylock nuts that attach the brake cylinder to the stamped bracket (at 3:09 in the video). I've double checked everything, laid all of the parts out on the floor, and those are definitely missing.
Good video, thanks. I have a different problem. Would like to replace the stock rear sets on my Triumph 900 Thruxton with stock foot pegs and shift pedal and brake pedal... is the truxton set up to take stock Bonneville shifter and brake pedal or it does it take a special kit?
Hi Brian, This is quite a common conversion on the Thruxton, you would need these Bonneville parts- rear brake master cylinder, right and left footrest hanger plates , 2 x footpegs , brake and gear lever. we make alloy brake and gear lever and alloy footpegs but the other parts would need to be sourced and normally found used on ebay.
Nice product ! and seems reasonably priced compared to others on the market . Any chance you could let me know how far up and back the center of the footrest is positioned compared to stock . Cheers
I have a 2010 Bonnie. Now I can't get right side cover on properly? Is this a flaw in design? No instructions given in video or with kit. Little disappointed currently. Is there a quick fix for this?
Hi we have found on some models that Triumph has used a large diameter stop light switch ,you will simply need to change this to a smaller aftermarket switch
I also had the same problem today fitting to my 2003 Bonnie. Panel doesn't close and the master cylinder rod definitely has to be on the outsideof the bracket using the spacer. Mine just cleared on the inside so I though was OK but when I test rode my bike it rattled loudly and caused some brake fluid to leak. Hopefully my brake cylinder is still OK.. And the gear shifter bracket hits the o.e.m exhaust so I had to adjust it forward which makes the linkage rod too long so I had to put the gear shaft bracket forward which doesn't look or function as good as it should be. I bit disappointed considering its sold as a kit to fit all models of air cooled Bonevilles 2000-2016.
you may need to fit a slim brake light switch if your bike has the 'fat' type fitted,another fix is to use a spacer on the right side panel between the frame and panel on the fixing screw
![The Wall Song ร้องข้ามกำแพง | EP.213 | กรีน อัษฎาพร | 3 ต.ค. 67 [1/5]](http://i.ytimg.com/vi/3KrlLbCsadI/mqdefault.jpg)
![[UNCUT]"ตุลามรณะ"ย้อนฟังคำทำนาย หมอดูทุกสาย ดวงเมืองร้อน (หมอปลาย ฟองสนาน อ.โอเล่)I คนดังนั่งเคลียร์](http://i.ytimg.com/vi/lE5az5VvT9M/mqdefault.jpg)
Amazing video, and nice looking kit! What would have been nice to see is a before and after with a rider sitting showing us the difference in the foot and leg position.
Can't seem to find these kits on your website, though, can you provide a link please?
Very nice! Do you do something similar for my Street Twin too?
I would also be interested in this.
Those are very clean and neat looking rear set, can this be fitted to honda CB 1100 EX (2017) ?
My kit doesn't have the M8 bolts and nylock nuts that attach the brake cylinder to the stamped bracket (at 3:09 in the video). I've double checked everything, laid all of the parts out on the floor, and those are definitely missing.
Do you have some kit to moves rider pegs front, not back ?? thanks
Good video, thanks. I have a different problem. Would like to replace the stock rear sets on my Triumph 900 Thruxton with stock foot pegs and shift pedal and brake pedal... is the truxton set up to take stock Bonneville shifter and brake pedal or it does it take a special kit?
Hi Brian, This is quite a common conversion on the Thruxton, you would need these Bonneville parts- rear brake master cylinder, right and left footrest hanger plates , 2 x footpegs , brake and gear lever.
we make alloy brake and gear lever and alloy footpegs but the other parts would need to be sourced and normally found used on ebay.
My side cover won’t fit with all of this installed
Does this fit the 2017 street cup?
Nice product ! and seems reasonably priced compared to others on the market . Any chance you could let me know how far up and back the center of the footrest is positioned compared to stock . Cheers
Hi
moves the footpegs back 110mm and 65mm up
Thanks very much for the reply George .
TEC Bike Parts How do you replace the right side cover. It hits the master cylinder
you need to re locate the brake pipe
TEC Bike Parts can you elaborate a bit? I'm about to order these but want to be prepared for all steps. Thanks!
I have a 2010 Bonnie. Now I can't get right side cover on properly? Is this a flaw in design? No instructions given in video or with kit. Little disappointed currently. Is there a quick fix for this?
Hi
we have found on some models that Triumph has used a large diameter stop light switch ,you will simply need to change this to a smaller aftermarket switch
I also had the same problem today fitting to my 2003 Bonnie. Panel doesn't close and the master cylinder rod definitely has to be on the outsideof the bracket using the spacer. Mine just cleared on the inside so I though was OK but when I test rode my bike it rattled loudly and caused some brake fluid to leak. Hopefully my brake cylinder is still OK.. And the gear shifter bracket hits the o.e.m exhaust so I had to adjust it forward which makes the linkage rod too long so I had to put the gear shaft bracket forward which doesn't look or function as good as it should be. I bit disappointed considering its sold as a kit to fit all models of air cooled Bonevilles 2000-2016.
Hi
we have found some bikes have a large stop light switch fitted you need to swap for a slim type
Could you post a link to a suggestest switch?
Could you post a link to a suggested switch?
Hi have you developed something like this for Street Twin yet?
we make adjustable rider pegs and these will adjust enough for most situations without the need for full rear set kit
Will these fit the new T120, or are there any plans to introduce a T120 version any time soon?
sorry only for the air cooled bonnie at the moment
TEC Bike Parts how about Bonny 2013 SE does it fit on right side perfectly ?
you may need to fit a slim brake light switch if your bike has the 'fat' type fitted,another fix is to use a spacer on the right side panel between the frame and panel on the fixing screw
TEC Bike Parts how do I do that ? How do i fit a slim brake light switch in ?
Interested in this as well!
These should just come with paper instructions.