Thank you! I forgot to mention that my 2011 EX is the 4 cylinders . I think it already have wiring harness to plug the flog light in. This video is helpful.
You would have to modify and change the factory wiring to get it to work like you want. Or you can simply install the switch and leave them turned on all the time. If you do that they will automatically come on when your headlights are on.
What other equipment do I need if I were to still install the kit on a LX by splicing through the parking lights. Also, would I need to disconnect the battery if I were to do that? Thanks in advance!
I have a 2012 accord LX, could I pull wires into the harness to add the circuit for the fog light to alter it to work with the OEM Switch? Or would I have to run it to a switch? I do a lot of controls electrical for industrial environments so I could probably figure it out at some point but if I could get some insight from someone who is knowledgeable about Honda's electrical system that would be very helpful! Thank you for any help that you may be able to provide.
Disconnecting the battery is always a good thing. As far as the modification you have planned I have no idea. We have never tried what you are planning.
I would like to add fog lights to my 2011 Accord SE, is pre-wired and I already installed the factory switch. The fog lights come with the metal bracket but I can’t find the plastic trim/bezel used in this video to mount them to the bumper and hide the screws. I want to avoid getting another bumper, any advice is much appreciated. Thanks
@ chhonda. I have 2011 EX. My question is @ step "Mark cutting and drilling location. I see those marker before you actually use the white marker on it. Is that drawing already there ? Or does the Flog light kit has a template helping you to draw cutting/drilling location ? Thanks
Hey Guys, I have a question. I have a 2011 Honda accord EX and I don't have the holes on my front bumper to install fog lights. and I see on this video it had to be cut manually. Where can I get that done? Can I just go to my local Honda Dealer to get this kind of work done?
Hi bro Im going to upgrade my 2008 EX sedan. Refer your vid At 3:42 you pulled the wire (The vehicle 1 pin connector ). Please advise where it come from? You just install together with new switch or it was available to be there? Thank so much.
@@CollegeHillsHondaAccessories Thank you so much. I removed front bumper and found them at both sides of headlights wire. It means that once I install the switch and turn it on the current will supply to the pins? One more thing, do I need any relay if I replace halogen bulbs by LED bulbs 35w/bulb?! Wait for your help 😁
@ college hill Honda .. Am desperate really need to add fog lights to my 2012 Honda Accord SE, I understand base on reading through the comments that there ain’t no wire harness on the the SE but can u provide me with a link to witch fog light kit would work, I plan to have a professional electrician installed the wire harness.
Another question; does the bumper on my 2011Accord SE have the same cut-outs as the EX? Because if it does, I can buy the fog light kit from you guys and just wire it myself...
So this kit is just for EX models right? Can a different kit still be install on a LX by making the holes etc? I seen fog light kits that are compatible with LX on ebay that are for sale. If so, can we do that or will the wiring be a problem?
I'm sure there are some aftermarket kits available for the LX. The problem with the OEM kit is the LX does not have a compatible engine wiring harness.
I have a Honda accord 2008 EX or EX-L (Navigation), am I able to have fog lights on my car? and the light switch u used, is that the same 6 cylinders light switch?
I have a 2011 Accord with the factory fog lights installed. I just need to change the bulbs. is there an easy way to do it without removing the bumper, or is that the only way? Thanks!
+Christopher Perkins For the right side you are going to pull down a portion of the lower splash shield, for the left you will pull back part of the inner fender liner.
I have an 08 accord exl sedan 4 cylinder. I understand it comes pre wired. I already have the v6 bumper on I just wanna know where I can purchase the wiring harness.
I have a 2016 Honda Accord Lx. Is there any way possible to do something like this but for the headlight assembly? I really like the DRL that the Accord Sport has and would love to install it on my car. Is there any way possible? Thanks!
+Michael White The 2009 kit is different than in the video above. You can view instructions here. www.collegehillshonda.com/instructions/accord/2009/foglights.pdf
Hey CollegeHillsHonda, for this modification/add-on: are the steps identical for a 2008 EX-L Navi Sedan I4? I know your site has the instructions via pdf but just wanted to ask.
+Angel Benitez There is always a way to work around these kinds of issues. We personally however have not installed the kit on a LX so we can't provide any details.
We don't have any experience with fog light kits other than Honda so I wouldn't feel comfortable recommending anything. Maybe someone else here can chime in on a good aftermarket alternative.
www(dot)ebay(dot)com/itm/like/370946322585?lpid=82 Those are chrome fog lights. So if your accord has some chrome edging, it will mesh well. I would go with these. You just need to look up a manual, get the car up on front jacks, and have a few handy tools for the job if you want to do it yourself (and save around $200)
Is there any other style of fog lights compatible with my car or are those the only ones? i would like something like this www.ebay.com/itm/2011-2012-Honda-Accord-Sedan-Fog-Lights-08V31-TA0-100A-/281354865285?pt=Electric_Vehicle_Parts&hash=item41820e8a85&vxp=mtr but idk if its compatible
College Hills Honda exactly i don't like the fog light design of the one you sent me. Is there one similar to the one in the video that is compatible with my car or is there only one?
can you send me an link for fog lights, harness wire and the switch for my honda accord lx p 2010 sedan. i'am planning to put one on my car thanks in advance
Thank you!
I forgot to mention that my 2011 EX is the 4 cylinders . I think it already have wiring harness to plug the flog light in.
This video is helpful.
Can I do this on my honda accord 2010 ex L
🔥🔥🔥 Wasn't sure about doing this myself but now I definitely doing it
That’s awesome. I was going to buy a v6 front end to convert the fogs. So are the wires all ran in already? Does your kit come with the light switch?
You would have to modify and change the factory wiring to get it to work like you want. Or you can simply install the switch and leave them turned on all the time. If you do that they will automatically come on when your headlights are on.
I have Honda Accord Ex-L 2010, will it work, my car's front bumper has no holes, as of now, how much cost to install them ?
What other equipment do I need if I were to still install the kit on a LX by splicing through the parking lights. Also, would I need to disconnect the battery if I were to do that? Thanks in advance!
@ThePokeAdvice The back of the bumper is scribed so you know where to cut.
@bvipod This kit is not designed to work with 2008-2010 bumpers.
I have a 2012 accord LX, could I pull wires into the harness to add the circuit for the fog light to alter it to work with the OEM Switch? Or would I have to run it to a switch? I do a lot of controls electrical for industrial environments so I could probably figure it out at some point but if I could get some insight from someone who is knowledgeable about Honda's electrical system that would be very helpful! Thank you for any help that you may be able to provide.
Albert Homem There are others I believe that have adapted the kit for the LX. Try www.driveaccord.net.
@flkendall Have not had the opportunity to film it yet.
OK where are you guys located at ? you are not in Texas- Dallas, are you ?
should make a video for the coupes
Disconnecting the battery is always a good thing. As far as the modification you have planned I have no idea. We have never tried what you are planning.
I would like to add fog lights to my 2011 Accord SE, is pre-wired and I already installed the factory switch. The fog lights come with the metal bracket but I can’t find the plastic trim/bezel used in this video to mount them to the bumper and hide the screws. I want to avoid getting another bumper, any advice is much appreciated. Thanks
@12stevenscastor Honda does not offer a fog light kit for the LX model.
Nice, thanks for the video!
In the honda store shows the fog lights positioned in the middle of the area. Is that based on the model?
Hi there how can I order the Foglight assembly
Honda time is 2 hours. Our labor rate is currently $92 per hour.
Is there a link for this whole kit id really like to upgrade my 2012 Accord 2.4 EX
@chhonda Thanks. But before I order the fog lights I was wondering if a 2010 Accord LX-P install these Fog Lights?
Yay, back to cutting again!
Another great video. Thanks!
@ chhonda.
I have 2011 EX. My question is @ step "Mark cutting and drilling location. I see those marker before you actually use the white marker on it. Is that drawing already there ? Or does the Flog light kit has a template helping you to draw cutting/drilling location ?
Thanks
@Preluding99 For a first timer I would say 2-4 hours. With experience under 2 hours.
Is it possible to install a v6 bumper on a 2010 lx sedan? They look the same but I want fog lights bad and I can get the bumper at a good price!
The engine cabin harness does not have the required wiring on the SE.
Do all Honda Accords come pre-wired for fog lights or just the EX? I have an 2009 LX. Thanks
will that be able to fit on my Honda Accord Se? If so, where did you bought the front bumper? TY! :)
How much total is it to get this done at the dealership?
Yes. Information at 7:45 in the video.
what model of car are the lights installed to look for them on ebay
Is it a template on the back of factory bumper to go by I know most Hondas an Acuras have dem if it original OEM bumper
Hey Guys, I have a question. I have a 2011 Honda accord EX and I don't have the holes on my front bumper to install fog lights. and I see on this video it had to be cut manually. Where can I get that done? Can I just go to my local Honda Dealer to get this kind of work done?
This kit is only available for EX and up models.
Hi bro
Im going to upgrade my 2008 EX sedan. Refer your vid At 3:42 you pulled the wire (The vehicle 1 pin connector ). Please advise where it come from? You just install together with new switch or it was available to be there? Thank so much.
The 1 pin connector is part of the engine harness.
@@CollegeHillsHondaAccessories
Thank you so much. I removed front bumper and found them at both sides of headlights wire. It means that once I install the switch and turn it on the current will supply to the pins? One more thing, do I need any relay if I replace halogen bulbs by LED bulbs 35w/bulb?! Wait for your help 😁
@@xecophinhodiyer7797 We install LEDs here without additional equipment.
Where can i get the parts for the fog lights installation?
@CHEVAVAL04 yea but its still possible to have foglights on a lx rite
can you list all the specific tools and all the specific drill bits for each step? Thank you
+NBROOLS Go to our website to print out detailed instructions.
The 2008 kit is different. But yes there is a Honda kit available for your vehicle.
i have a 2008 basic option 4 cylinder without fog light, bought a bumper with fog lights in used how do i connect it?
@@the2paths You will still need most of the components out of the accessory kit to get them to work. Harness, switch, etc.
Can i use this kit on a bumper that already has the foglight holes? (Looking to get a new bumper)
@lilchit0 I was thinking the same thing! I just wanna make sure that bumper will fit my 2010 lx
There is no direct plug and play Honda option available.
how much does it cost to install on a 2010 Lx, approximately? my local dealer say they don't do these so they don't know
is the wiring and turn signal the same for my 2009 accord EX-L 2 door?
The Honda fog light kit will not work with the LX.
you have to buy the new switch separately or do they usually come with a kit?
will this work for my 2009 accord ex-l? if so where can i get the fog lights and the new arm for the light/foglights switch? thanks
The marks are already there. They are just outlining them so they are easier to see.
Where can I get this done? Every auto bodyshop I call doesn't do it near where I live Western Mass
Juan Santana Visit a dealer as a first option. Second option would be to find a good independent shop.
@ college hill Honda .. Am desperate really need to add fog lights to my 2012 Honda Accord SE, I understand base on reading through the comments that there ain’t no wire harness on the the SE but can u provide me with a link to witch fog light kit would work, I plan to have a professional electrician installed the wire harness.
there no way to this work in the Lx?
@CHEVAVAL04 no its not unfortunately i have an lx and you gotta cut a whole in the bumper
Can i do this to my 08 accord ex? they look the same
The coupe kit is very similar.
i have a honda accord 2009 4drs EXL, i wonder if a bumper cover with fog light can fit onto it
Great video. I have a 2011 Accord SE and am interested in this kit. Will it work?
EX models only.
Oh well... thanks anyhow.
Another question; does the bumper on my 2011Accord SE have the same cut-outs as the EX? Because if it does, I can buy the fog light kit from you guys and just wire it myself...
Yes the bumper is the same on the EX.
Cool!
Will be ordering the light kit very soon...
The 2009 kit is different. 7:45 for more information.
how come honda didnt make a hole like the 03-07 models...
only if those fog lights fit the 08-10 bumper...
could u do the fog light installation for the 9th gen accord please
Victor Sandoval If we get the opportunity we most certainly will.
Will this fog light install work on my 2012 Accord SE? Thanks!
So, there's no way to get fog lights for my SE?
@baha2021 EX and EX-L models only.
Can I do this for my 2009 4cyl accord?!
I have the same car and the same problem, and I am interested in buying the kit fog lights could you send me the link please??
how much i can get it done for a 2011 lx
@thugy504 The kit will not work with LX-P models.
around h
ow much would a shop charge for this exact same process to be done?
That will vary by labor rate. Book time is 1.6 hours.
would this kit work without the plastic thing on the bumper?
+Andrian Stefanus Not this particular kit, no.
+College Hills Honda is there another kit that doesn't involve the plastic piece? If I use a v6 bumper would it work?
+Andrian Stefanus I have heard of people swapping bumpers and putting together a custom fog light kit.
Como lo consigo porfavor
This modification is compatible with my 2008 honda accord EX-L ?
There is a separate fog light kit for 2008-2010 models.
would this work on my 2011 accord SE..
So this kit is just for EX models right? Can a different kit still be install on a LX by making the holes etc? I seen fog light kits that are compatible with LX on ebay that are for sale. If so, can we do that or will the wiring be a problem?
I'm sure there are some aftermarket kits available for the LX. The problem with the OEM kit is the LX does not have a compatible engine wiring harness.
Unfortunately not. It is for EX and up models only.
I have a Honda accord 2008 EX or EX-L (Navigation), am I able to have fog lights on my car? and the light switch u used, is that the same 6 cylinders light switch?
I have a 2011 Accord with the factory fog lights installed. I just need to change the bulbs. is there an easy way to do it without removing the bumper, or is that the only way? Thanks!
+Christopher Perkins For the right side you are going to pull down a portion of the lower splash shield, for the left you will pull back part of the inner fender liner.
Thanks for the help!
I have an 08 accord exl sedan 4 cylinder. I understand it comes pre wired. I already have the v6 bumper on I just wanna know where I can purchase the wiring harness.
I HAVE A 2012 ACCORD SEDAN IT DOESNT COMES WITH THE FOG LIGHTS IN THE BUMPER, I WANT TO CHANGE IT TO ONE WITH FOG LIGHTS WITCH DO RECOMMEND ?
How different is this for 2012 lx S? I already have fog light holes. Can I follow all other steps?
Honda does not offer a kit for the LX or LXS.
Those would be for a vehicle older than 2009.
Can I have this done in my 2005 accord (4 doors, v6, 3.0 engine and navigation)? If yes where can I buy the kit?
www.collegehillshonda.com/product/08V31-SDA-101.html
I have a 2010 Honda Accord LX (bas model) would I be able to install this on my car or get a shop to do?
Unfortunately this kit is for EX and up models only.
i have a 2011 honda accord lx-p can i use those fog light ?
I have a 2016 Honda Accord Lx. Is there any way possible to do something like this but for the headlight assembly? I really like the DRL that the Accord Sport has and would love to install it on my car. Is there any way possible? Thanks!
You would have to swap out headlight assemblies and maybe change some wiring.
are their any fuses or relays left out of this video looking to install on my 2009 accord ex-L
+Michael White The 2009 kit is different than in the video above. You can view instructions here. www.collegehillshonda.com/instructions/accord/2009/foglights.pdf
Hi i know this is a old video. But will this kit work on 2010 accord sedan ex-l model 4 cyl. Thx
Where can I buy the kit from?
www.collegehillshonda.com/product/08V31-TA0-100A.html
I have a 2012 Honda Accord Special Edition, Will this work on my Accord?
eek, not sure bud. You should probably dig in some more research. Go to Honda dealer and ask the service guys about it.
Hey CollegeHillsHonda, for this modification/add-on: are the steps identical for a 2008 EX-L Navi Sedan I4? I know your site has the instructions via pdf but just wanted to ask.
The 2008 fog light kit is a different installation.
In comparison to this video, would it be more difficult or about the same?
About the same difficulty.
Will these fog light assemblies fit a 2012 Accord SE, and I can run an independent wiring harness
EX and EX-L trims only.
@@CollegeHillsHondaAccessories so just the fog lights will not fit the bumper on the se?
@@bryanpineda8614 The fog light assemblies will fit but the vehicle will not have the wiring present for the accessory harness.
@@CollegeHillsHondaAccessories perfect, do you guys sell just the fog light assemblies then. I can wire them in no problem
@@bryanpineda8614 The fog light brackets are the problem. They are not available separate from the fog light kit.
Will this kit fit my 2012 Honda Accord SE?
EX and up only.
Would this work on my 2012 Honda Accord Sedan LX? If not why?
+Angel Benitez The factory engine harness on the LX is not compatible with this kit.
+College Hills Honda so you would just have to wire it different? With another switch? I'm trying to see if I can have a electrician install it.
+Angel Benitez There is always a way to work around these kinds of issues. We personally however have not installed the kit on a LX so we can't provide any details.
Can u send me a link for the oem kit for a 2011 honda accord ex sedan
www.collegehillshonda.com/product/08V31-TA0-100A.html
Hi I have a 2009 honda accord lx what kind of fog light your RECOMMEND
We don't have any experience with fog light kits other than Honda so I wouldn't feel comfortable recommending anything. Maybe someone else here can chime in on a good aftermarket alternative.
Ok thanks
*****
are you driving a 2 door coupe or 4 door sedan?
4 door sedan !
www(dot)ebay(dot)com/itm/like/370946322585?lpid=82
Those are chrome fog lights. So if your accord has some chrome edging, it will mesh well. I would go with these. You just need to look up a manual, get the car up on front jacks, and have a few handy tools for the job if you want to do it yourself (and save around $200)
Will this work for a 2012 Honda Accord se?
+datchulo1085 Unfortunately not.
Aftermarket kit it is I guess 😩. Thank you for the response . Have a happy new year
I just buy a 2010 accord exl will this fit?
+Alex Rodriguez This is for 2011-2012.
do they sale just the light I don't need the wires
Yes you can purchase just the fog light assemblies.
Do u know how much
It is cheaper to buy the whole kit. Individual assemblies are about $140 each.
I have a 2008 honda accord EX Sedan 2.4L and i want to install fog lights on it. Is this compatible with my car?
This is the wrong kit for your vehicle. You would want this instead.
www.collegehillshonda.com/product/08V31-TA0-100.html
College Hills Honda thanks for letting me know i would have brought them :)
Is there any other style of fog lights compatible with my car or are those the only ones? i would like something like this www.ebay.com/itm/2011-2012-Honda-Accord-Sedan-Fog-Lights-08V31-TA0-100A-/281354865285?pt=Electric_Vehicle_Parts&hash=item41820e8a85&vxp=mtr but idk if its compatible
***** That is the same kit as shown in the video.
College Hills Honda exactly i don't like the fog light design of the one you sent me. Is there one similar to the one in the video that is compatible with my car or is there only one?
Hi, I have a HONDA ACCORD EX_L 2008 V4, can i install this?
Not this exact kit but there is a similar kit for the 2008.
College Hills Honda Where to buy the kit?
Bing Liu
www.collegehillshonda.com/product/08V31-TA0-100.html
can you send me an link for fog lights, harness wire and the switch for my honda accord lx p 2010 sedan.
i'am planning to put one on my car
thanks in advance
Honda does not have an OEM option for the 2010 LX.
Good
This will vary dealer by dealer due to part price and labor rate.