SolidWorks API Tutorial #4: Introduction to SketchManager and FeatureManager

แชร์
ฝัง
  • เผยแพร่เมื่อ 10 ธ.ค. 2024

ความคิดเห็น • 17

  • @solidworkstutorials4305
    @solidworkstutorials4305 13 วันที่ผ่านมา

    Excellent and very well explained for beginners. Thank you

  • @ze1184
    @ze1184 ปีที่แล้ว +1

    Great job, Me_in_3D. A sincere thanks from a mech eng a decade later.

  • @joeten4817
    @joeten4817 6 ปีที่แล้ว

    very well explained. Hope you continue the series. I will be looking out for newer videos!

  • @LuisFernando-hy6gn
    @LuisFernando-hy6gn 7 ปีที่แล้ว

    Excelent!! Very thanks!!

  • @rohitpharande5607
    @rohitpharande5607 7 ปีที่แล้ว

    nice tutorials

  • @DanPlaysonYT
    @DanPlaysonYT 8 ปีที่แล้ว

    hey in trying to copy how you added the breaks into the code but for somereason solidworks 2015 is not allowing me to do it, got any ways around it??

  • @prajwalshinde2321
    @prajwalshinde2321 7 ปีที่แล้ว +1

    at the end when i start to run it ,it shows-user defined type not defined, and there is an error in the first line where you write sldworks.sldworks. Please tell me what should i do.

  • @farzadtb
    @farzadtb 8 ปีที่แล้ว

    thanks a lot for sharing , yet I don't know how can I put a angle dimension , for example 45 and not 135 , then control it with the macro

  • @234erwr
    @234erwr 9 ปีที่แล้ว

    Hello , I`m using SW2010 and I don`t have file Part.pztdot , where I can find it?

  • @sdeepak656
    @sdeepak656 8 ปีที่แล้ว

    nice video!
    can you provide help on creating a series of radial center lines from origin.
    i need it to be done in the following sequence
    1. create centre line 1 through origin.
    2. insert point with reference to center line 1 at a distance x
    3. add centre line 2 at an angle 1deg from centerline 1 and again insert point at a new distance x2.
    i need to program this upto 360 degrees.
    could you help?

  • @sheikabdullah179
    @sheikabdullah179 5 ปีที่แล้ว

    How to link the dimension from excel to SolidWorks model instead of typing in the VBA

  • @rpas1982
    @rpas1982 10 ปีที่แล้ว

    Hey there, any ideas on how to Insert Reference Planes offset from the top plane. I have tried using a recorded macro to create a ref plane; however every time i run it the created plane does not appear. Any help would be appreciated.

    • @jasonbarbeiro272
      @jasonbarbeiro272 10 ปีที่แล้ว

      Hey, are you able to download the file from the link below? The file is a macro I recorded that creates many reference planes offset from the top plane.
      www.dropbox.com/s/4nxj9iuc7b8948j/Making%20Plane.swp?dl=0

    • @rpas1982
      @rpas1982 10 ปีที่แล้ว

      hey, thanks for that. The link works. I ll have a look at the macro and try running on mine. I ll come back with comments once I go through it. Thanks again.

    • @rpas1982
      @rpas1982 10 ปีที่แล้ว

      Hey Jason, Thanks for the macro. It does seem to be running ok; however for some reason the created planes do not appear in the solidworks part that I ran the macro on. I am running SW 2012 SP0 (it's an unofficial version).

  • @danapatelzick9812
    @danapatelzick9812 8 ปีที่แล้ว

    I noticed you used a definition of meter in inches, actually the definition of an inch is 25.4mm per inch exactly. For your conversion dim{in meters}=dim{inches}*.0254. This is the cause of your cylinder being 11.9999 long rather than 12.00 long

  • @rubenhogt9708
    @rubenhogt9708 9 ปีที่แล้ว

    Got a question, could you copy that feature extrusion code and put it in the discription or send me a personal message containing it?
    Thanks in advance,