Gas pistons wouldn't move down but found the solution - the gas pistons were so stiff they literally wouldn't move a cm, we thought they needed replacing but they didn't - the key is to pull down with both hands WHERE THE PISTON is with the mattres on top, this way the force goes right on it, and less likely to damage the bed from too much force at the end - this way you can get it moving and doing it on both sides loosens them up enough for it to work properly
Quick question i have double ottoman gas bed i want to paint/decorate my sons room, do i need to take all the storage out from the underneath, & mattress off then just slowly lift the bed frame to the side to paint the wall. Or do i need to completely open the entire bed again. When i bought my bed the workers fixed/assembled the whole bed for me.
Hi, A couple of the wooden slabs broke on mine and I'm trying to fit replacement parts. I'm having trouble getting the plastic fittings for the wooden slabs out of the frame so I can put new ones in. Any idea how to get the old ones out?
@@JevonRandh hello, had the bed for about 5 years, but after a very hot weather the wooden slaps just fall out Like they shrunk, I know wood won't shrink The frame is twisted to 1 side & hard to keep down flat ?
@@empireman1077 you need to move the bottom corner of the bed either to the right or left slightly this will make it square, even on both sides so there is no strain or stress on the parts.
Hi nice vid. I have an issue. On one of the side panels, the screws holding the bracket in place have gone downwards so much, ripping the wood. They will not stay in place no matter how much i tighten them. The bed now goes down on one side. How to proceed?
Found the solution - the gas pistons were so stiff they literally wouldn't move a cm, we thought they needed replacing but they didn't - the key is to pull down with both hands WHERE THE PISTON is with the mattres on top, this way the force goes right on it, and less likely to damage the bed from too much force at the end - this way you can get it moving and doing it on both sides loosens them up enough for it to work properly
Thank u I have a question I have the same put I’m missing some of those lil black things to put together how do u call the and where can I buy them please thanks
I have set up about 20 similar beds a day, and the floor you have set up is no use at all because it is a very thin and fragile fabric. We used wooden floors so that the bed has much more resistance.
wd40 and my full body weight wouldnt move one ditached piston, tried the methonf whilst attached to the bed and we ended up sat on either side ontop of the bed to get it to move....it didnt, FLM
Please contact the provider or you may buy from your local DIY store, Thanks, Please do not forget to subscribe and share Jevon Randh recipes only channel in Konkani.
Thanks man, only got half the bed delivered at first with no instructions. Raging, I got a refund and then the other half came 😂 still no instructions though so thank you very much.
Thanks this has just helped me when putting together this bed. Those pistons had me bamboozled
Great to hear!
Gas pistons wouldn't move down but found the solution - the gas pistons were so stiff they literally wouldn't move a cm, we thought they needed replacing but they didn't - the key is to pull down with both hands WHERE THE PISTON is with the mattres on top, this way the force goes right on it, and less likely to damage the bed from too much force at the end - this way you can get it moving and doing it on both sides loosens them up enough for it to work properly
Thanks, Please do not forget to subscribe and share Jevon Randh recipes only channel in Konkani.
Yesssssss thank you, I've spent the last 4 hours going mad about it thinking I did something wrong, that was extremely helpful thanks 🙏🏽
You're a legend mate!!
Thanks a lottttttt!! U were a saviour !! God bless
Thank you very much,your video help my husband so much. Gracie.
I'm so glad!, Thanks, Please do not forget to subscribe and share Jevon Randh recipes only channel in Konkani.
Thanks for taking the time to show us how to assembled the Ottoman storage bed...OKAY
I appreciate
Quick question i have double ottoman gas bed i want to paint/decorate my sons room, do i need to take all the storage out from the underneath, & mattress off then just slowly lift the bed frame to the side to paint the wall. Or do i need to completely open the entire bed again. When i bought my bed the workers fixed/assembled the whole bed for me.
Honestly, if you have enough space move to otherside.
Thank you mate, i am getting the same bed next week, cheers!
Glad I could help
Where do you get the bed from
@@bluebear6133 Amazon
@@JevonRandhthe
How is it mate?
Hi, A couple of the wooden slabs broke on mine and I'm trying to fit replacement parts. I'm having trouble getting the plastic fittings for the wooden slabs out of the frame so I can put new ones in. Any idea how to get the old ones out?
If these are difficult to find, sawn timber are easily available in the DIY stores, cut them according to your size, hope this would help
@@JevonRandh hello, had the bed for about 5 years, but after a very hot weather the wooden slaps just fall out
Like they shrunk, I know wood won't shrink
The frame is twisted to 1 side & hard to keep down flat ?
@@empireman1077 you need to move the bottom corner of the bed either to the right or left slightly this will make it square, even on both sides so there is no strain or stress on the parts.
Can you set gas lift both side ? Right or left?
yes, both sides
Hi nice vid. I have an issue. On one of the side panels, the screws holding the bracket in place have gone downwards so much, ripping the wood. They will not stay in place no matter how much i tighten them. The bed now goes down on one side. How to proceed?
When I insert the gas bar it stops the bed from moving up and down completely. How do I fix it??
Please check if the gas bar is working, inform the manufacture to replace it.
Or check if it's the right way round
Found the solution - the gas pistons were so stiff they literally wouldn't move a cm, we thought they needed replacing but they didn't - the key is to pull down with both hands WHERE THE PISTON is with the mattres on top, this way the force goes right on it, and less likely to damage the bed from too much force at the end - this way you can get it moving and doing it on both sides loosens them up enough for it to work properly
Thankyou for this video
My pleasure 😊
Thank you man, I thought my pistons were broken but was just a bit stiff.
Thanks, Please do not forget to subscribe and share Jevon Randh recipes only channel in Konkani.
I have the same problem, put the mattress on the frame, still stiff
Thank u I have a question I have the same put I’m missing some of those lil black things to put together how do u call the and where can I buy them please thanks
black clamps?
Do you have the memory fo as m mattress for the same bed bug a small double?
Thanks, Please do not forget to subscribe and share Jevon Randh recipes only channel in Konkani.
This video was a huge help. Many thanks!!
Glad it helped!
Thanks!! This was a very helpful video
you are welcome
Thank you. Very helpful
Glad it was helpful!
How do you fit the gadget that stops the mattress sliding off?? Just bought one and cannot figure it out!!
make sure the bed on a flat surface
What do you call the wooden strips and from where one can buy those ?
wooden slats, Thanks, Please do not forget to subscribe and share Jevon Randh recipes only channel in Konkani.
Hi,
What are the tools you have used to assemble the bed?
Is the tool same for every bed?
if you are assembling this type of Ottoman Bed, than yes.
Allen key is the tool
what is that velcro handle thing called?
Does anyone know the specs on the screws that fastens the pistons ?
try DIY shop
How do I insert a wooden slab back in after it fell out?
I had this similiar problem, I bought similar size from my local DIY shop and cut into exact size and replaced it.
My bed won’t close after assembly, is there a way to resolve this?
restart whole process again, Thanks, Please do not forget to subscribe and share Jevon Randh recipes only channel in Konkani.
hey can you get the bed to lift from any side?
that's true
@@JevonRandh thankyou so much!!
on the bottom frame can you take them off again
you can
Thank you so much 💕💕
Thanks, Please do not forget to subscribe and share Jevon Randh recipes only channel in Konkani
what are the black brackets that you used to connect the wood together called ?
BLACK METAL CORNER BRACKETS OTTOMAN LIFT UP BED SPARE PARTS
can you open it from either side?
👍
Hi I'm currently assembling this bed right now and the pistons/hydraulics are very stiff any idea how to fix, thanks
assemble them and see if they are working
Hi did you get this fixed? I got a bed today and they’re so stiff they won’t go down no matter how much Force is applied :(
@@anj4776 ya it actually work when we put my mattress on it, the pistons worked straight away
@@anj4776 please contact your bed supplier
You are not meant to lift it up and down until mattress is on.
Can u choose which side it lifts from
sure,
Thank you so much
👍
I have set up about 20 similar beds a day, and the floor you have set up is no use at all because it is a very thin and fragile fabric. We used wooden floors so that the bed has much more resistance.
👍
Yip like cheap weed suppressant. I need mine higher off tge floor wood a wooded thick frame attached work then paint it same colour as base
Hi, when we order online these beds, do they come with base cardboards or not like those that sit on the floor?
Awesome thanks
Did you add lift up to regular bed?
no, Thanks, Please do not forget to subscribe and share Jevon Randh recipes only channel in Konkani
So helpful. Thank you!
Glad it was helpful!
Thank you
Mine wont stay up with the mattress on top ,if I take the mattress off it stays up. Any ideas what I'm doing wrong
Please try again
Looks nice, where did u get from? Amazon? Or IKEA?
Ebay
Nice one really helpful
Glad to hear that,
This beds are original from the ottoman empire is ottoman design beds am I correct
Thanks, Please do not forget to subscribe and share Jevon Randh recipes only channel in Konkani.
Where did you get the bed from ?
online
Online from where ?
@@svanaunni4124 Argos
Thx so much
Thanks, Please do not forget to share Jevon Randh recipes only channel in Konkani
wd40 and my full body weight wouldnt move one ditached piston, tried the methonf whilst attached to the bed and we ended up sat on either side ontop of the bed to get it to move....it didnt, FLM
okay
Thanks!
Thanks, Please do not forget to subscribe and share Jevon Randh recipes only channel in Konkani.
Can you let us know where to buy one?
try Amazon
I bought mine from wayfair
My bed didn’t come with the black cover on the bottom but it’s the same bed
Please contact the provider or you may buy from your local DIY store, Thanks, Please do not forget to subscribe and share Jevon Randh recipes only channel in Konkani.
how long did it take you to do this
approximately 2 hrs
Patrao...
From Chief Cook to Fitter zalo kit re 😂😂
Nonetheless 👍
Thanks, Please do not forget to subscribe and share Jevon Randh recipes only channel in Konkani.
@@JevonRandh but this is not cooking mure.. but I see all recepies...
Just an ad, 🤣
My slats always snap off when I put to much weight on bed
🤣
My pistons arent working ones stiff the other let the thing drop on my fingers 😭
Thanks man, only got half the bed delivered at first with no instructions. Raging, I got a refund and then the other half came 😂 still no instructions though so thank you very much.
Glad I could help
I got given the wrong amount of bolts, what do I do?
contact the company you purchased from
They don’t care
which company?
Jevon Randh is it possible for you to come and build mine I have the bed frame just not the slats n metal parts
@@thekiwifruit3659 SUE 'EM
Feet? Mine's got feet, but it looks like I need to drill into the frame to fit them, as there are no holes!
there is nothing on the bottom
How much it cost you?
$380
@@JevonRandh ihave buy same bed for 170$in offerup..in usa!😉
U missed the part how the frame goes in or connects to the weight bar
👍
Ive ordered end lift is it same assembly as no instructio with it
Let's go to woodprix, if you want to learn how to build it yourself.
Please try
@@JevonRandh OK
Didn't show what size screws went in where 🙄
sizes are different for every bed
Wish we saw this before taking 7 hours to build super king size same as this NEVER AGAIN
thanks
Thank you - Hare Krishna
Thanks, Please do not forget to subscribe and share Jevon Randh recipes only channel in Konkani.
OOOOOOO the bed will collapse ,!!! you have the washers and the spring washers on the wrong side ,my friend
Thanks, Please do not forget to subscribe and share Jevon Randh recipes only channel in Konkani.
Mine doesn’t stay down help me
Please do not forget to subscribe and share Jevon Randh recipes only channel in Konkani.
👌
👍
😂😂😂😂 worke Lol
Thanks, Please do not forget to subscribe and share Jevon Randh recipes only channel in Konkani.
That Bett is Not good at all
No sense
Please do not forget to subscribe and share Jevon Randh recipes only channel in Konkani.
Thank You. Very Helpful!
Thanks for watching, and please "Subscribe & give Thumbs Up", if you have not done so, also Spread the word "Jevon Randh" Recipes.