Drawing Machine Assembly and First Try

แชร์
ฝัง
  • เผยแพร่เมื่อ 4 ก.พ. 2017
  • Complete Bill of Materials:
    3dmake.club/articles/drawing-m...
    Files and software:
    3dmake.club/articles/drawing-m...
    My build of Drawing Machine by cyul (www.thingiverse.com/thing:1514145) with some little changes.
    Here is an assembly video.
    I ordered all the electronic components, rods,bearings, etc on AliExpress
    Linear Shafts 8mm*400mm - 2pcs - ali.pub/1xattp
    Linear Shafts 8mm*320mm - 2pcs - ali.pub/1xatr6
    Linear Shaft 6mm*200mm - 1pcs - ali.pub/1xax78
    LM6UU Bearings - 2pcs - ali.pub/1xau1h
    LM8UU Bearings - 8 pcs - ali.pub/1xatyr
    16 Teeth 5mm Bore Timing Pulleys - 2 pcs - ali.pub/1xavsh
    16 Teeth 3mm Bore Idler Pulleys - 1 pcs - ali.pub/1xawbj
    No Teeth 16 3mm Bore Idler Pulleys - 4 pcs - ali.pub/1xawbj
    GT2 Belt - 2m - ali.pub/1xaudq
    Arduino + CNC Shield + A4988 Drivers - 1 pcs - ali.pub/1xaukc
    Nema 17 Stepper Motors - 2 pcs - ali.pub/1xath9
    28BYJ-48 12V Stepper Motor - 1 pcs - ali.pub/1xaupz
    Wiring Kit - 1 pcs - ali.pub/1xauz4
    Power Source 12V 4A - 1 pcs - ali.pub/1xav4r
    M3 Bolts - ali.pub/1xasl6
    M3 Nuts - ali.pub/1xasw2
    Buy in local hardware store:
    M10*400mm Threaded Rods - 2 pcs
    M10 Nuts - 8 pcs
    M3*8mm Bolts - 11 pcs
    M3*20 Bolts - 10 pcs
    M3*30 Bolts - 8 pcs
    M3 Nuts - 22 pcs
    Inkscape gcode output extenstion for this thing based on MakerBot Unicorn gcode Output Extension: rgho.st/6xLQH5WJv
  • วิทยาศาสตร์และเทคโนโลยี

ความคิดเห็น • 312

  • @SuperMaDBrothers
    @SuperMaDBrothers 3 ปีที่แล้ว +10

    I'm totally digging the music

  • @anasrahman4729
    @anasrahman4729 8 หลายเดือนก่อน +2

    thanks a lot sir for a complete guide about grbl modification. you are only one who tell this. thanks again

  • @mohammedebrieeshetie790
    @mohammedebrieeshetie790 3 ปีที่แล้ว

    MATHIMATICS I ACTION , THANKYOU FOR SHARING THIS HOME MADE DRAWING MACHINE

  • @shinlau3002
    @shinlau3002 5 ปีที่แล้ว

    thank you for the stuff.
    what is the firmware you used to control the Z axis with the 28BYJ-48 12V Stepper Motor please?

  • @hardikvora8756
    @hardikvora8756 5 ปีที่แล้ว

    Hello Konstantin Konstantinov, I have already built the cnc plotter but I can not control the pen rise and fall.
    I do not know if it has to do with the gcode file created in inkscape. When I am printing the pen is always in the same position, it does not go up or down. Can you help me?

  • @GoutamNarayan
    @GoutamNarayan 6 ปีที่แล้ว

    If I want to increase my plotting area, what should I do? Will increasing the shaft size only do the job or shall I need to modify the electronics and code also?

  • @icetoolz2486
    @icetoolz2486 7 ปีที่แล้ว

    классный станок, классный видос, классная музыка)
    Теперь осталось сделать так, чтобы в штатив можно было и фрезер поставить, и выжигатель...

  • @mousa65
    @mousa65 6 ปีที่แล้ว +1

    Very nice Drawing Machine, I am building one for me. Thank you for sharing.

  • @williamnguyen686
    @williamnguyen686 6 ปีที่แล้ว

    If I increase the length of each X axis and Y axis to 100mm, do I need to change the code and modify the software?
    And where do they change?

  • @sandeepthale8477
    @sandeepthale8477 6 ปีที่แล้ว

    Too awesome work dear...
    Can we use same mechanism for 2axis hotwire CNC machine?

  • @Kri5A
    @Kri5A 4 ปีที่แล้ว

    How do I change the surface of drawing area ? I want to build a drawing machine with an area of 100cm x 100cm .

  • @richardhargreaves8132
    @richardhargreaves8132 4 ปีที่แล้ว +1

    which inkscape plugin is being used to create the Gcode?

  • @user-ol3or3hc9y
    @user-ol3or3hc9y 4 หลายเดือนก่อน

    My cnc pen plotter is going on the wrong side. When it draws the picture, it is not in this direction, but it is moving to the left side. how to fix it? Is it a software problem?

  • @ln4951
    @ln4951 5 ปีที่แล้ว

    Подскажите пожалуйста куда подключить серву и нужен ли драйвер Zоси на шилде (при использовании сервы)? Собрал как в видео, все заработало. Есть необходимость на Z поменять мотор на серву. Пробовал grbl файл для сервы - машинка не работает совсем.

  • @srejth
    @srejth 5 ปีที่แล้ว

    What is the length of the threaded shaft and what is the measurement that it can draw (ie, Draw a maximum larger border line measurement L X W) Please reply..,...

  • @bwalker7143
    @bwalker7143 4 ปีที่แล้ว

    I have just built one like this but the controls are 45 degrees off as the clock turns. Is there something GRBL or $$ that can be changed to fix this?

  • @ED-zp8zn
    @ED-zp8zn 2 ปีที่แล้ว

    Hello, may I ask does this work with colour paintings? Thank you.

  • @Nomad_Wanderer
    @Nomad_Wanderer 6 ปีที่แล้ว +8

    Built the same with just Rs.2500 including all the parts mine was laser cut, rods were salvaged from old printers and the steppers were also from old xerox machines... The acrylic used was 16mm, 10mm & 6mm.. 120kg for acrylic scrap, parts took around 14mins to cut on co2 laser CNC 14mins x Rs. 8 = Rs.112, steppers cost Rs.60 each minebea 1.7amp 1.8deg, cnc shield +arduino uno+pololu stepsticks driver=Rs.1200, linear bearing Rs.600...

    • @PrathameshJakka
      @PrathameshJakka 6 ปีที่แล้ว +2

      make a tutorial

    • @mustafamahameed6649
      @mustafamahameed6649 6 ปีที่แล้ว

      Khadim Ali where and how I can get it?

    • @lucianosantos5036
      @lucianosantos5036 6 ปีที่แล้ว

      Please, could you provide the dxf files? Unfortunatelly, I don't have 3d printer, just a small cnc router.

    • @furqanahmed6
      @furqanahmed6 6 ปีที่แล้ว

      AA . Khadam Ali bhai . I want to see this machine . Can I contact you or can I buy from any place . Plz ? SMS me 03227663131

    • @ann-kathrinv3963
      @ann-kathrinv3963 6 ปีที่แล้ว

      Hey ! Any chance I could get access to your laser cut files ? I wanted to print them first, but I guess printing them with an old ultimaker could be difficult. I would really appreciate your help !(: Thank you!

  • @karfex
    @karfex ปีที่แล้ว

    Hello, the page with the software information does not work, what is the name of the software you use?

  • @nathangonzalez382
    @nathangonzalez382 5 ปีที่แล้ว

    Hi, I want to know how I could get the whole package to put together and how much would it cost? Thank you .

  • @zainabalshouli5166
    @zainabalshouli5166 7 ปีที่แล้ว

    how did you connect the 28byj to the shield? the 28byj have 5 wires i you need 4 for the shield.

  • @lordelectron6591
    @lordelectron6591 3 ปีที่แล้ว

    Can i use longer screw shafts
    For bigger drawings?

  • @MrNonozor
    @MrNonozor 4 ปีที่แล้ว +1

    How to wire the pen holder motor, because it has five connectors while the cnc shield has only four connectors for each stepper ?
    Thank you for this great project.

    • @ashiksaleem360
      @ashiksaleem360 3 ปีที่แล้ว

      Pen is controlled by a servo i guess

  • @ChristopherDesa
    @ChristopherDesa 3 ปีที่แล้ว

    I was so impressed with your build. That I also build 1 like this. But theFiles and software link is broken. If you could share the files please

  • @francisconoronha7458
    @francisconoronha7458 6 ปีที่แล้ว

    Hello Konstantin Konstantinov, I have already built the cnc plotter but I can not control the pen rise and fall.
    I do not know if it has to do with the gcode file created in inkscape (mac), or if it has to do with the program I use to print (cncjs - mac).
    When I am printing the pen is always in the same position, it does not go up or down and gives the error id = 23.
    Can you help me?

    • @francisconoronha7458
      @francisconoronha7458 6 ปีที่แล้ว

      Hello again Konstantin Konstantinov, I do not use any command in gcode to control the Z axis. I simply load the gcode file that was generated in inkscape and say to print.
      What is the correct way to do, and how to command the Z Axis?

    • @francisconoronha7458
      @francisconoronha7458 6 ปีที่แล้ว

      ty

  • @EmptyChannelMC
    @EmptyChannelMC 6 ปีที่แล้ว +1

    Nice video. Wanted to see how the movement work, it looks like CoreXY.

  • @jantatarski5716
    @jantatarski5716 7 ปีที่แล้ว

    Hi, can you put a drawing file for example square or rectangle, because i have probably connected the wrong motors.

  • @michaelnoardo3315
    @michaelnoardo3315 6 ปีที่แล้ว

    do you think it is worth using this project for a 3d printer?

  • @AdamVenomStudios
    @AdamVenomStudios 6 ปีที่แล้ว

    Hello, good job on builing it, looks great, thinking about making a similar one. What plastic did you use for parts? How much money did you pay for printing more or less? Peace!

  • @maxyar0n
    @maxyar0n 6 ปีที่แล้ว +1

    Hi Konstantin,
    Great job, I like it.
    I already build similar drawning machine, but have a problem with calibration xy axis.
    Can you tell me please, how to set the working surface of the machine (via inkscape or by arduino?)
    Thanks in advance.

    • @sagnikghosh630
      @sagnikghosh630 7 หลายเดือนก่อน

      Same problem with me...did you fix it?

  • @jamilbarbar
    @jamilbarbar 6 ปีที่แล้ว

    Good project. Could you list the bolts, nuts and screws, etc.? Thank you.

    • @3DMake
      @3DMake  6 ปีที่แล้ว +1

      Hello, I have made a full bill of materials, take a look in video description

  • @maximilianluv1
    @maximilianluv1 6 ปีที่แล้ว

    i find amaizing what u did !!! And i want to make also one like u did, at the moment i study electronics and i think it will help me a lot. a detailed instruction i found also at the website adress that you provide in the description but i need to know if :
    do i need a 3d printer ??
    do i need linux ?

  • @vikashkumaryadav1470
    @vikashkumaryadav1470 3 ปีที่แล้ว +1

    Where I can buy it.

  • @onluyentoancaocap8911
    @onluyentoancaocap8911 7 ปีที่แล้ว

    dear konstantin. what did you insert on board shield before inserted a4988? thank you so much

    • @onluyentoancaocap8911
      @onluyentoancaocap8911 7 ปีที่แล้ว

      at 12:40. you insert things. before a4988?glue gum or anything?

    • @onluyentoancaocap8911
      @onluyentoancaocap8911 7 ปีที่แล้ว

      ok. thank you so much. you connect pin ms1, ms2, ms3 to vcc for 1/16 step? and we'll can use inkscape for gcode file?

    • @onluyentoancaocap8911
      @onluyentoancaocap8911 7 ปีที่แล้ว

      oh yeah. i understood. thank you so much. i'll diy it with material from old scanner and printer. hi

    • @swaseenacute2202
      @swaseenacute2202 7 ปีที่แล้ว

      Konstantin Konstantinov are the micro shunt jumpers necessary?

  • @michelgroenen9408
    @michelgroenen9408 6 ปีที่แล้ว

    Where must i the belt together ???
    I make this machine but wen i rotate one motor the machine move in 2 direction

  • @santoshchaudhary8686
    @santoshchaudhary8686 ปีที่แล้ว

    hello sir when i move x+ it moves diagonally can you help me to solve the issues

  • @TheKingAdel
    @TheKingAdel 5 ปีที่แล้ว +4

    New link for writing kit please

  • @mariacifuentes7198
    @mariacifuentes7198 2 ปีที่แล้ว

    Hi, how do i modified the code so that it recognizes M3 and M5 commands?

  • @battleprasad24
    @battleprasad24 5 ปีที่แล้ว +3

    can you send me link of software and program link

  • @gsaravanan9969
    @gsaravanan9969 6 ปีที่แล้ว

    Hi, how do you manage z axis movement!

  • @mohanmony01
    @mohanmony01 6 ปีที่แล้ว

    Hi there. I got little problem when i make a print it printing 45 degree angle why it’s happen?

  • @abhinfrndz
    @abhinfrndz 6 ปีที่แล้ว +2

    How do you route the belts ?

  • @tonnguyen1531
    @tonnguyen1531 6 ปีที่แล้ว

    Can someone help me?. Why have some change the code in 16:33 ??
    What is the function when you change this ?

  • @peekaboowi2668
    @peekaboowi2668 7 ปีที่แล้ว +1

    I tried to download the gcodecreate.zip but it said that it is a virus.
    Can I get a safe download somewhere?

    • @onluyentoancaocap8911
      @onluyentoancaocap8911 7 ปีที่แล้ว +1

      can i help you peeka? i installed it. and using it. not virus.

  • @u-lo-l
    @u-lo-l 6 ปีที่แล้ว +8

    I want to know how belt was connected

  • @Shinobi_Chronicles
    @Shinobi_Chronicles 6 ปีที่แล้ว

    sir can you plz tell me that how did you mount that gt2 pulley..?

  • @amrzakaria5290
    @amrzakaria5290 ปีที่แล้ว

    Good job , can you sent new link for your files.

  • @vishnuprem8437
    @vishnuprem8437 7 ปีที่แล้ว

    Greetings from dubai!
    I plan on making this same arm. Can you explain in detail how you connected the belt? Also can I use this same mechanism with longer rods to cover 40x40 cm paper?

    • @vishnuprem8437
      @vishnuprem8437 7 ปีที่แล้ว

      Ohh okay got it. Just to clarify you are using just one single belt that runs through the arm right?
      Also what is the reach of the arm in the video?

  • @theindia9725
    @theindia9725 ปีที่แล้ว

    Sir ,Kindly make vedio on software installation n implementation .

  • @omtapkir8639
    @omtapkir8639 ปีที่แล้ว

    There are no endstops for homing?

  • @NIKHILkumar-gp2cf
    @NIKHILkumar-gp2cf 6 ปีที่แล้ว +2

    How did u assemble belt

  • @nemoskull2262
    @nemoskull2262 6 ปีที่แล้ว +1

    i still dont get how you get 2 axis motion with both stepper on the x axis...:( didnt show the cable routing.

    • @RJFeddeler
      @RJFeddeler 6 ปีที่แล้ว +1

      I've been designing my own and use the same belt system. I found this video which explains the motion: th-cam.com/video/_nzxGOKhHSY/w-d-xo.html

    • @melvinjaysewane7762
      @melvinjaysewane7762 4 ปีที่แล้ว +1

      @@RJFeddeler thank you for the link and saving my day pal.

  • @MrBobWareham
    @MrBobWareham 6 ปีที่แล้ว

    what can I say magic the music and video well done and thanks

  • @thetungtran5575
    @thetungtran5575 7 ปีที่แล้ว +1

    how to wiring motor to cnc shield board, please master ?!

  • @farqadal-safi2999
    @farqadal-safi2999 6 ปีที่แล้ว

    Just haw u connect the GT2 belt ?? plz answer

  • @DETUDOUMPOUCO-ne6js
    @DETUDOUMPOUCO-ne6js ปีที่แล้ว

    I've been trying for 6 months now but the servant doesn't
    I don't know what else to do!!

  • @trexarain794
    @trexarain794 3 ปีที่แล้ว

    Can it be used for writing?

  • @g2david
    @g2david 6 ปีที่แล้ว

    How can I connect to servo? which pin should I use?

  • @MustafaTokay
    @MustafaTokay 6 ปีที่แล้ว

    hi, thank for video is best :D
    what you are using to open your .h files ? 16:36 ?

    • @3DMake
      @3DMake  6 ปีที่แล้ว +1

      It is a Kate, standard text editor in Kubuntu. You can use any text editor like Notepad

    • @MustafaTokay
      @MustafaTokay 6 ปีที่แล้ว

      again hi :) this time it gives such an error can you help me what should i do? Error: Expected command letter

  • @barsbilginuyar5817
    @barsbilginuyar5817 6 ปีที่แล้ว

    Do the parts have a 3D printer view

  • @marting.4350
    @marting.4350 3 ปีที่แล้ว

    Can you please share the software and firmware link. Link is dead

  • @francisconoronha7458
    @francisconoronha7458 6 ปีที่แล้ว

    Hi, Konstantin Konstantinos, congratulations for the video. It's very useful.
    Can you send me the link to the 3D part that supports the arduino. That it does not exist in the site where they are, another. Thank you

  • @antonioceddia3278
    @antonioceddia3278 3 ปีที่แล้ว

    I would like to buy only the plastic parts, how can I do?

  • @dhanakodimani4783
    @dhanakodimani4783 5 ปีที่แล้ว +1

    I followed all ur steps..in gcode sender.. i upload a gcode file.. it doesnt working..

  • @NIKHILkumar-gp2cf
    @NIKHILkumar-gp2cf 6 ปีที่แล้ว

    Can u make a belt setup video

  • @trexarain794
    @trexarain794 3 ปีที่แล้ว

    Can it be used for writing

  • @eko653
    @eko653 7 ปีที่แล้ว

    What kind of 3d printer is this??
    I would like to buy one but I have no idea what should I choose...

    • @eko653
      @eko653 7 ปีที่แล้ว

      the malyan m150 doesn't look very promising to me... Witch one do you use?
      I am looking right now at a Tevo Tarantula what do you think of it?

  • @mehmetgunes9252
    @mehmetgunes9252 3 ปีที่แล้ว

    Can you share if there is a grbl download link?

  • @mgssivaprasad2484
    @mgssivaprasad2484 5 ปีที่แล้ว

    This machine worked based on inkscape Android application or not..??

  • @mariofares9701
    @mariofares9701 5 ปีที่แล้ว

    how much filament did it took?

  • @carlosceballos2024
    @carlosceballos2024 6 ปีที่แล้ว

    Hola, amigo como puedo adquirir ese producto. Por favor ayudame.

  • @sainishiv3484
    @sainishiv3484 6 ปีที่แล้ว +2

    how to insert belt plzz explain properly

  • @bayunugrahasuparto9639
    @bayunugrahasuparto9639 2 ปีที่แล้ว

    can you provide 3d printing file? thank you very much🙏

  • @SFan-im2tv
    @SFan-im2tv 6 ปีที่แล้ว

    Please anyone can help me ? I want to build same one, but bigger, were can I buy the staff please help me

  • @GroGaloraGran
    @GroGaloraGran 6 ปีที่แล้ว

    Did not understand the GT2 pullout scheme of the belt (

  • @MineOrebaker
    @MineOrebaker ปีที่แล้ว

    Files and software link doesn't lead to me download link will you please send me the link or directly to me !!

  • @AnupumPant
    @AnupumPant 6 ปีที่แล้ว

    Could someone please explain how do the belts go around the pulleys? I just don't understand because it's all happening inside and it's keeping me awake at night.

    • @RJFeddeler
      @RJFeddeler 6 ปีที่แล้ว

      I just responded to one of the other many comments asking about the belts and see you asked just 6 days ago so I wanted to make sure you saw it so I'm posting it again. th-cam.com/video/_nzxGOKhHSY/w-d-xo.html

  • @venkatanikesh9748
    @venkatanikesh9748 6 ปีที่แล้ว

    can I get the STL files of these 3d prints

  • @sainishiv3484
    @sainishiv3484 6 ปีที่แล้ว +2

    how to insert belt explain properly

  • @cadnaanstudio
    @cadnaanstudio 4 ปีที่แล้ว

    Thanks for your video i have 3 questions
    1. you included in your order Linear Shaft 6mm*200mm - 1pcs and i didn't saw in your video
    2. The Bore timing pulleys you wrote 16TB5 are they 16T 6W B5 or 16T 10W 5B
    3. what is that Linear shaft at 15:02

    • @AyobeTech
      @AyobeTech 3 ปีที่แล้ว

      The Linear shaft is cut two pieces 100mm x 2 , and this it at 15:02

  • @abhisheklawand6382
    @abhisheklawand6382 5 ปีที่แล้ว

    how to make plastic stage ,end 1, end2 ,pen holder and its procedure

  • @jeanraines3215
    @jeanraines3215 3 ปีที่แล้ว

    Why can't the STL files be opened

  • @jekRaffio
    @jekRaffio 6 ปีที่แล้ว

    Ciao, come mai a me scrive come se fosse riflesso in uno specchio ?

  • @krunalkevlani9026
    @krunalkevlani9026 3 ปีที่แล้ว

    Can you tell me the scale size of all components please

  • @marcelooroquieta9842
    @marcelooroquieta9842 6 ปีที่แล้ว

    Which one did you use? 28BYJ-Stepper 5V or 12V?

  • @onluyentoancaocap8911
    @onluyentoancaocap8911 7 ปีที่แล้ว

    dear konstatin. can your machine write a letter or create signature? is this axidraw machine?

    • @onluyentoancaocap8911
      @onluyentoancaocap8911 7 ปีที่แล้ว

      so. how can i write a letter? or create signature. i use inkscape to make gcode. but i don't know how to make this machine can write line.
      do you have facebook? we can add friend and chat together.

    • @onluyentoancaocap8911
      @onluyentoancaocap8911 7 ปีที่แล้ว

      i use axidraw hatch fill extension tools

  • @raul7293
    @raul7293 2 ปีที่แล้ว

    I like those Indian drums in the background. I use that those sounds meditate. I like the video. ThanQ

  • @williamnguyen686
    @williamnguyen686 6 ปีที่แล้ว

    I can change use size machine (500mm-long and 420mm-long) ?

    • @tinyfeeme4411
      @tinyfeeme4411 5 ปีที่แล้ว

      William Nguyen of corse!

  • @The025697
    @The025697 3 ปีที่แล้ว

    good day ! tell me how to tune the servo motor in arduino by 90 degrees of deflection and then return to the zero point! I need to attach a marker! Thank you

    • @oldmemo937
      @oldmemo937 3 ปีที่แล้ว

      You need to tune it in gcode.
      Watch this. At last there are two options. Mess with the values.th-cam.com/video/H5_i8ruAXno/w-d-xo.html

  • @user-pr4ki5yi6u
    @user-pr4ki5yi6u 6 ปีที่แล้ว

    В чем измеряется размер чертежей 3д обьектов?

  • @williamnguyen686
    @williamnguyen686 7 ปีที่แล้ว

    What are some of your minor changes?

  • @anshifa6996
    @anshifa6996 3 ปีที่แล้ว

    What is the torque of this stepper motor

  • @sandipsen7926
    @sandipsen7926 5 ปีที่แล้ว

    Mind blowing ideas....

  • @doitdude684
    @doitdude684 3 ปีที่แล้ว

    Send link of this background music

  • @mateusznowak3646
    @mateusznowak3646 5 ปีที่แล้ว

    which power supply is good

  • @user-pr4ki5yi6u
    @user-pr4ki5yi6u 6 ปีที่แล้ว

    What is measured by the size of drawings of 3D objects?

    • @3DMake
      @3DMake  6 ปีที่แล้ว

      Даня Сорокин
      Не очень понял вопрос?

  • @chikenpaww
    @chikenpaww 4 ปีที่แล้ว

    Where the hell I can buy those 3d printed center plastic

  • @igorzimonin7115
    @igorzimonin7115 7 ปีที่แล้ว +1

    Потрясающая работа =)

    • @LOLSGE
      @LOLSGE 5 ปีที่แล้ว

      Потрясающая музыка я хочу слушать ее

  • @antunesserrao1366
    @antunesserrao1366 4 ปีที่แล้ว

    How do I buy this material?

    • @milayoung5803
      @milayoung5803 4 ปีที่แล้ว

      Here is www.3dmaxprinter.com/shop/do-it-youself/polar-pen-drawing-machine-plotter-arduino-diy-kit/

  • @impedrofer
    @impedrofer 6 ปีที่แล้ว

    Can you just say what type of screws you are using. Type and dimensions please.

    • @3DMake
      @3DMake  6 ปีที่แล้ว

      Hello, I have made full bill of materials, take a look in video description