So after your advice. Today I was able to use the ford F038 after multiple failed attempts. My issue was I wasn't using enough tension and because of this, they weren't binding. I also learned that on some spots you have to click it into place twice until it gets springy. Also I was mistaken some wafers for springy when they weren't. Thank you my friend
That is Awesome insight! I am getting better at determining the slight bouncies from the legit bouncies but prax will get me there. Over setting is definitely my worst enemy and for some reason I assumed you didn't have to worry about the 1 cut as much. Thanks for clarifying otherwise!
Nope. I get all these locks at junkyard. Those cars aren’t in America so I can’t get a lock. Toy48 and hy22 on my channel are 4 lifter Lishi. Not sure if they’re similar to va6 or not
I wish you had shown the bounce/travel on the ones you didn't need to pick. You knew the depths ahead of time, but that's obviously not the case for a practicing locksmith. Did the 4 depths bounce consistently from the get go or did they slightly bind at first?
I am a locksmith. Use these everyday. What I recommend doing is getting locks that you have a key so you know the bitting and you then can develop a feel for what the 4 depths feel like. I didn’t touch them because I was. Trying to the hammer home the point that they don’t need to be picked.
@@BoredLockpicker Had to come back and thank you again. Using these tips I lishid a door cylinder in 2 minutes whereas before it would have taken me forever!
I have been trying to pick a HU100 trunk lock for about a week without success. However, I have started to notice, no matter how much tension I use, wafer #5 refuses to set. Is it possible I have a damaged lock?
Is it a 4 cut? If it is you don’t need to pick it. If if you don’t have a key you send me the lock. I’ll make one. Of course the lock could be damaged but I would be surprised since the trunk lock barely would get used.
Hu100 is easy though lol. The door is fine. If the first two wafers really aren’t there. Just use code fill on insta code or lock codes and you’ll be good. If you don’t get a valid decode pick at the other way and it should work
@@BoredLockpicker i have the older lishi that you mentioned gets stuck in ignition . But it came with the hu100 mockup key. Instead of a shim..Can i use that to get it unstuck? Is it thick/thin enough?
Greetings to your presence, I am a follower, your explanation is excellent. Possible after your permission I want to list all lishi keys that work on me all normal locks and all middle east cars
So after your advice. Today I was able to use the ford F038 after multiple failed attempts. My issue was I wasn't using enough tension and because of this, they weren't binding. I also learned that on some spots you have to click it into place twice until it gets springy. Also I was mistaken some wafers for springy when they weren't. Thank you my friend
Awesome! And you’re welcome
That is Awesome insight! I am getting better at determining the slight bouncies from the legit bouncies but prax will get me there. Over setting is definitely my worst enemy and for some reason I assumed you didn't have to worry about the 1 cut as much. Thanks for clarifying otherwise!
You’re welcome!
Love your videos !!
There is any chance your making a tutorial on va6 4 lifters that will be a fantastic
Nope. I get all these locks at junkyard. Those cars aren’t in America so I can’t get a lock. Toy48 and hy22 on my channel are 4 lifter Lishi. Not sure if they’re similar to va6 or not
Could you use the 10 cut lishi on 8 cut locks to prove it reads correctly and does work properly. Im afraid the spacing would be off a bit.
Just buy both. Never know when you’ll need a ten cut ignition
I wish you had shown the bounce/travel on the ones you didn't need to pick. You knew the depths ahead of time, but that's obviously not the case for a practicing locksmith. Did the 4 depths bounce consistently from the get go or did they slightly bind at first?
I am a locksmith. Use these everyday. What I recommend doing is getting locks that you have a key so you know the bitting and you then can develop a feel for what the 4 depths feel like. I didn’t touch them because I was. Trying to the hammer home the point that they don’t need to be picked.
These are my nemesis. Thank you for the tips
I never have issues picking them. They just don’t always decode easily
@@BoredLockpicker Yes that's what I meant to say. Sometimes I'll pick a lock and then insert the lishi to read. If I can get the pick out.
@@BoredLockpicker Had to come back and thank you again. Using these tips I lishid a door cylinder in 2 minutes whereas before it would have taken me forever!
@@pearljameric I’m glad it help. With practice most them aren’t to tough. I’m going to hopefully get another toy48 video up today
@@BoredLockpicker I'll be looking for it. Gonna turn on the bell
I have been trying to pick a HU100 trunk lock for about a week without success. However, I have started to notice, no matter how much tension I use, wafer #5 refuses to set. Is it possible I have a damaged lock?
Is it a 4 cut? If it is you don’t need to pick it. If if you don’t have a key you send me the lock. I’ll make one. Of course the lock could be damaged but I would be surprised since the trunk lock barely would get used.
Thanks for the tip!!!
You’re welcome
HU100 mở loại cửa xe đời nào bạn . Cảm ơn bạn ❤
GM high security
hey..on a 2020 GMC ..it says ignition is an 8 cut..door from 3 to 8..so I just leave 1, 2 alone? then use instacode for remaining two?
If they aren’t in the lock use lock codes or insta code. Or just pick the ignition
@@BoredLockpicker always have a hard time picking ignitions cuz of the angle 😅
Hu100 is easy though lol. The door is fine. If the first two wafers really aren’t there. Just use code fill on insta code or lock codes and you’ll be good. If you don’t get a valid decode pick at the other way and it should work
@@BoredLockpicker i have the older lishi that you mentioned gets stuck in ignition . But it came with the hu100 mockup key. Instead of a shim..Can i use that to get it unstuck? Is it thick/thin enough?
Anything that can push the dust cover in
Greetings to your presence, I am a follower, your explanation is excellent. Possible after your permission I want to list all lishi keys that work on me all normal locks and all middle east cars
You have to look up the silca key blank to know which Lishi to use on the car.
@@BoredLockpicker
Sorry, I am new in this profession and I do not know how to find possible an explanation to find the solution