I replaced it because I had some issues with carging and with my microphone. It worked, but very quiet couldn't hear anything. When on speaker then it works fine enough. So I replaced charging port and charging is fine now but microphone still doesnt work. Thanks in advance
My phone would only charge in fast mode with one particular charger and cable. Otherwise, I would see a message reporting slow charging. The predicted time was often 25-30 hours, but charging always completed much faster (5-10 hours). The other symptom is that all OTG storage devices were not recognized. I tried replacing the charger port as described, but after the replacement, the fingerprint reader stopped working and none of the other symptoms went away. So, I put the original part back. Fingerprint reader is now working again, but the other symptoms are back. Thinking of trying another part. Any idea why the fingerprint reader stopped working with the replacement part?
Mine for sure isn't water proof ... That's why it won't charge it says water detected in the port and starts vibrating. I ordered the actual charging port only, if it's soldered on will I need the charging board?
Does it still survive dipping in water? Still has ip 67 rating water resistant? Even I changed my galaxy a52 4g charging port in samsung service center I don't about water resistant still works or not can you please explain about water resistance ip 67 rating after charging post replacement
UPDATE!!!! THE PORT IS STILL ON THE WAY. I REMOVED THE BACK, BLOW DRIED THE BACK AND CHARGE PORT, USED A NICE FANCIER CORD FROM A SOLANA SAGA TO CONNECT IT C TO C... ITS CHARGING!!!!!!!!! it may not again but rn the pos is charging after laying around for over a year. Now water detected symbol. This is a Samsung defect.... Obviously.
I replaced the board, now my phone resatrt randomly. Seems like an hardware connection problem. But i dont see any issue. Do u have any idea whatbis causing my problem?
@@michelearchitecturestudent1938 ok, my new board from amazon was defect. I put my old board in again and replaces the flex cable. Then it works fine for me. So the flex cable was the problem.
Hello sir. Can u pls replied to me , can u upload avdieo how to remove and fix sim slot that stuck on samsung A52 s 5g pls1😢😢. When i put sim tray pin it not working pls help
Please help i have switched the charging port. I have done everything correctly but now my phonr wont start or turn on. I did not disconnect the battery cable first because i watched another video and it didnt show that part. Is that what caused the problem? I took everything apart again and it still wont start
I don’t think it is because of the battery disconnecting issue. Maybe a faulty charging port , can you try with another one. Also double check all connectors. Is your battery is holding fine?
Just like someone else in the comments, my signal doesn't function anymore with the replacement part, while replacing the old one fixes the issue. Very sad that we can't buy parts directly off of Samsung and instead have to rely on third parties.
Just replaced mine and I'm still getting 'check charging connection' notification on my phone. My laptop still can't read my phone. I took my phone to get looked at and they couldn't find a solution.
@@DIYGeardo yes. Usb debugging, usb options on for transfer files, *#0808# and I have MTP + ADB on. I took my phone to another repair shop and got a new charging cable and charger that now I have fast charging again, but no computer can see my phone. Not even at the repair shop could they see my phone on. The guy told me I might have bought a faulty USB charger board.
Amazing video! You saved me from buying a new phone. Easy to understand instructions. THANK YOU!
Great 👍
Thank you so much for the guide guys, Easy to follow with simple steps. My phone can now be charged! Awesome
Great. Share and support. Thanks
Thank you so much for this video, you just saved me a couple hundred dollars. I went ahead and Liked + Subscribed
Thanks for your feedback 👃
Without this my repair would be impossible. Thank you guys!!!
Great
What kind of screwdriver is it?
I hav got samsung a52.... your video is very use..thanks brother.
Thanks you are welcome
Thanks alot for the help. My phone can now charge properly.
Nice to hear that
Great video. If the blue and white cables are reversed is that bad? Or are some phones manufatured that way?
You mean antennas?
@DIYGeardo If that's the proper nomenclature then yes.
The two cables press fitted on the circuit card. One white, one blue. Mine are reversed.
Hi , if i got a52 5g k2 , can i use a52s 5g k2 board they both look same and have same number on top right corner?
I don’t think it will work, but you can try. I’m. It sure about it exactly
Great video. I played and paused it on my computer while I worked on my phone. When I plug it in now, it frequently restarts. Any ideas?
Much appreciated.
You are welcome 🙏
Hi, is disconnecting the battery absolutely necessary? Thanks
Better to disconnect the power
what is the blue antenna for in this video? i broke mine but phone works good?
Signal Antenna
Thanks for the video
You are welcome 🙏
I replaced it because I had some issues with carging and with my microphone. It worked, but very quiet couldn't hear anything. When on speaker then it works fine enough. So I replaced charging port and charging is fine now but microphone still doesnt work.
Thanks in advance
is it important if the phone is A52s 5G SM-A528B K1 or K2 or DS when doing this process? or is the charging board/port universal?
thanks u so much bro its work
You're welcome!
Great video, helped a lot!
Great
the damage of charging port does cause battery time increment ????
It depends. But a faulty charging port will eventually stop working
can we get a52s 5g charging kit sir i want for my phone
Yes, if you need let us know.Thanks
Which model should I have buy k1 or k1
Will it still be waterproof?
Nope
My phone would only charge in fast mode with one particular charger and cable. Otherwise, I would see a message reporting slow charging. The predicted time was often 25-30 hours, but charging always completed much faster (5-10 hours). The other symptom is that all OTG storage devices were not recognized. I tried replacing the charger port as described, but after the replacement, the fingerprint reader stopped working and none of the other symptoms went away. So, I put the original part back. Fingerprint reader is now working again, but the other symptoms are back. Thinking of trying another part. Any idea why the fingerprint reader stopped working with the replacement part?
Did you replace with an original part? What type part is that?
This version of the board comes in either K1 or K2. Check the code on your original board and replace it with the same version.
I'm having the exact same issue rn lol
I have this problem right now. I am considering trying to replace the charging port. Did you ever fix the problem?
@@emilm6202 no.
I clean the Charge port of my phone n try to charged it again bt still it didn't work. Please help
Probably you have a bad charging port..
Mine for sure isn't water proof ... That's why it won't charge it says water detected in the port and starts vibrating. I ordered the actual charging port only, if it's soldered on will I need the charging board?
Are there different charging ports for A52 4G and A52 5G?
most of them are same
Does it still survive dipping in water?
Still has ip 67 rating water resistant? Even I changed my galaxy a52 4g charging port in samsung service center I don't about water resistant still works or not can you please explain about water resistance ip 67 rating after charging post replacement
Well, service centre repairs keep your waterproofing levels (As per reports)..Third parts is highly unlikely..But please check with the service store.
How to clean dust and foreign bodies in my a 52 Samsung charger pot
To clean dust you can use a cotton bud with 100% alcohol or perfume. For others will depend on what is inside
@@DIYGeardo thanks
What is the grey wire for?
Hello, mine is fully replaced, still not charging. I'm lost now what to check next? Thank you.
You need test with another unit. Sometimes the part can be faulty
The wire that connects the charging base and handsfree to the motherboard is often a problem
UPDATE!!!! THE PORT IS STILL ON THE WAY. I REMOVED THE BACK, BLOW DRIED THE BACK AND CHARGE PORT, USED A NICE FANCIER CORD FROM A SOLANA SAGA TO CONNECT IT C TO C... ITS CHARGING!!!!!!!!! it may not again but rn the pos is charging after laying around for over a year. Now water detected symbol. This is a Samsung defect.... Obviously.
Do the phone give back trouble agian once your fix it
Well mostly no, but it is a device, anytime can have an issue.
I only ordered the actual port for $7 not the whole board is it possible to fix it with just the port. How is the port connected to the board
You need to solder. It is too much work and better buy the complete board.
Is that samsung a52 and a52s has the same charging board?
Slightly different . Not same
@@DIYGeardo thank you! More power
is there any difference between a52 4g and a52 5g charging flex? Please some one help me to find
My A72 got charging problem should i change it
Try a different cable, if it is still happening, yes you might need to change it
Is heating necessary or can you pry it apart without heating?
It is very hard to remove without heating
I replaced the board, now my phone resatrt randomly. Seems like an hardware connection problem. But i dont see any issue. Do u have any idea whatbis causing my problem?
Same problem
@@michelearchitecturestudent1938 ok, my new board from amazon was defect. I put my old board in again and replaces the flex cable. Then it works fine for me. So the flex cable was the problem.
Am I correct in assuming the thermistor is on the charge port circuit board?
I think Yes..
Hello sir. Can u pls replied to me , can u upload avdieo how to remove and fix sim slot that stuck on samsung A52 s 5g pls1😢😢. When i put sim tray pin it not working pls help
Take off the back cover, and then take out the logic board. Afterwards you can take it out. But must tae out the back cover
@@DIYGeardoty for helping
Please help i have switched the charging port. I have done everything correctly but now my phonr wont start or turn on. I did not disconnect the battery cable first because i watched another video and it didnt show that part. Is that what caused the problem? I took everything apart again and it still wont start
I don’t think it is because of the battery disconnecting issue. Maybe a faulty charging port , can you try with another one. Also double check all connectors.
Is your battery is holding fine?
BANG BOARD CAS SAMSUNG A525F SAMA SAMSUNG A52 5G SAMA GAK
Same question
Would it still be waterproof
No, not really. But if you take to an official service center, they might.
Just like someone else in the comments, my signal doesn't function anymore with the replacement part, while replacing the old one fixes the issue.
Very sad that we can't buy parts directly off of Samsung and instead have to rely on third parties.
I did just as same as u did but its not charging pls help
after replacing pcp board my phone isnt recive any signal sim is working fine and on old pcp i have no problem with that
any idea why ?
Model number is same or not?
i have the Same Problem
modelnuber is the Same
i have tested it with two boards
any ideas?
@@johanneswalter2386 This version of the board comes in either K1 or K2. Check the code on your original board and replace it with the same version.
That's ridiculously hard, Samsung obviously did that on purpose knowing it's the part set to break eventually.
Compare to most repairs. This is not that bad.
@@DIYGeardo I've replaced a screen on an old phone. This repair looking at the steps you nearly need to tear down the entire unit.
charging port of a52 is compatible for a52s?
I think yes, not sure 100% percent, once i have info i will update
I think the charging works but the signal doesn't work..
Sir where I can by charging pcb bord on my samsung A52
Location?
@@DIYGeardo Kolkata
Sir please help me 🙏🙏🙏
@@riteshchakss4614 there should be many places you can look for with in India..did you check online stores?
@@DIYGeardo No sir, Plz Suggest me the online site?
Thaaaaaaaanks
You are welcome
Hello, what would be the best way to heat up the back cover if I don't have a heating pad?
As the video says, a hair dryer is fine.
Thx you saved our Ass.
Thanks for your feedback 👃
Just replaced mine and I'm still getting 'check charging connection' notification on my phone. My laptop still can't read my phone. I took my phone to get looked at and they couldn't find a solution.
Have you turn on the usb debugging mode?
@@DIYGeardo yes. Usb debugging, usb options on for transfer files, *#0808# and I have MTP + ADB on. I took my phone to another repair shop and got a new charging cable and charger that now I have fast charging again, but no computer can see my phone. Not even at the repair shop could they see my phone on. The guy told me I might have bought a faulty USB charger board.
How to buy charging board
Sorry for the delay..jstech.com.au
@@DIYGeardo I didn't find it
Folks he's taking of professionally but the back is easy to take of by hand
Way too much work...delete removing the camera cover, it is not necessary...don't you know that?
Don't you know that if you don't unplug the battery you can short something and damage the phone.
I hope that's a female tech, cuz the hands are kinda sexy
Haha
This phone sucks!
Pp