PURESINEWAVE INVERTER DC TO AC 1000W EGS002 (HIGH FREQ)
ฝัง
- เผยแพร่เมื่อ 27 ก.ย. 2024
- $2 for 2-Layer PCBs & $5 for 4-Layer PCBs: jlcpcb.com/DYE
1000W Continuous power pure sinewave inverter with EGS002, smooth sine wave, high-efficiency power inverter.
Download PCB layout here: bit.ly/2NseV8u
Inverter EGS002 Low-Frequency transformer: • 12/24VDC to 220VAC Inv...
DWYOR
idle current at 4.8A a very high idle consumption will drain the battery faster.. with low frequency transformer type at same power, idle current can be less than 2A. So far the demonstration was highly satisfactory. Nice work!
Just 0.6A idle
@@WahyuEkoRomadhon in the video we all saw 4.8A idling
@@WahyuEkoRomadhon retty easy to see how bad your inverter works!
Check his subtitles. He mentioned that a 60w soldering iron and 55w lamp are also connected , that's what drawing the current when the hot gun is off.
Super Hyper Rapi Dan Tampilannya Keren Banget projectnya Suhu 😁.. Ampunn 🙏😂...
Mmpung ad mas
ini baru suhu karya2 nya bener2 rapih seperti produksi pabrik, sukses mas eko, 👍👍👍👍👍
Thnks mas
TK tukune lek
@@imronmuhammad4678 tanya mas wahyu, pdhl sy juga berharap karya2 mas wahyu di pasarin di olshop apalagi power2 Class-D rakitan yang bisa di aplikasiin ke mobil, pasti sy minat banget daripada beli power2 branded yang harganya mahal dan gak terjangkau.
Buat produk2 yg bermanfaat untuk kemajuan negara kita mas, kembangkan terus mas
Very nice. Is any schematics and PCB along with software available for use, thanks.
Sudah saatnya orang kreatif seperti mas ini diajak kerjasama perusahaan buat merek sendiri dibidang elektro agar punya merek sendiri dalam negri dan bisa diexpor klr negeri juga, tentu dengan kwaltias terbaik
Amiin mas
@@WahyuEkoRomadhon aminnn moga cepat terjadi
Tambah grid tie function trus limiter sama datalogging.
Pasti lebih joss.
Cetak Pcb pakai Anti Nyamuk Sofell Nyimak aja lah😄😆.
Bang wahyu ga perlu diragukan lagi, mantap uey
Thanks bli
Bsa di beli bos
Produksi yg banyak dan harga bersaing mas, biar indonesia semakin maju dan bangga dengan buatan anak negeri
Amiiinn mas. Insyallah
Kalau pas cetak pcb lagi, saya pesan pcb nya mas untuk plts dirumah. Selama ini beli inverter yg udah jadi, kalau rusak bingung servisnya ngeliat jalur😄
Boss skli2 upload pilihan ampli terbaik versi smean🙏👍
How to adjust VFB Voltage, because when we try to adjust the output goes to shutdown.
Hey, how do you choose the RC combination you used for the SG3525 from compensation pin (pin 9) and inverting input (pin 1). As there is not much information about how to calculate it on the internet so pls if you could help me out 🙏
Lo felicito siempre con proyectos profesionales, muchas gracias.
sekarang lg rame2nya energi terbarukan.semoga di bahas lg tentang inverter kedepanya.seperti halnya clasd sa.at ini
joss kotos-kotos barang atos ojo nganti bledos...auto subrek mbah
Hello! Good work! But why a litz wire consists from such thick wires? When I made AC/AC HF converter from galogen lamps (300W) I had unsucces with thick wire 0.33millimeters. A transformer was too hot and a current density was roughly 2 A/mm2. When I change my homemade litz 0.33mm on 0.16mm the temperature of wire had been decreased much. It was a construction like a steel rope. 12 wires was a minimal twisted wire unit. These wires (5 unit) twisted into one - e.t.c. A current density was 4A/mm2.There wasn`t any cooler.
Use TDK EE-55 ferrite core more efficient brow...i got 93% eff based on egs002 high freq
Watt out?
What is the output wattage ?? And can you pls share the schematic and transformer winding detail it would be really helpful :)
Hi, congratulations!! Could you tell me if have you experienced any issue or problem with the LP filter?. Did you have any problems with L-C resonance? I have been working on a prototype using EGS002 (also using a compatible pinout board based on a PIC that I have been working on) and in both cases I had some problems with LCL filter. It seems that at resonance frecuency, there is a lot of energy and I can see high current peak across the capacitor in paralel branch, wich still remains if a limiting series resistor is added. I think it could be a matter of choosing the resonance frecuency which should not to be close to a (sub) multiple of switching frecuency (in EGS002 switching frec is around 22-23 KHz, in my board it is 25 KHz), but unfortunatelly I am not sure about it. I will aprreciate any comments about this subject. Thank you very much.
After 2 years,did you solve the problem?
Can it feed back into the grid?
It is at the bottom of the page but cannot be clicked. Gerber and file parts are clickable.
hello friend thanks for sharing your project. I have a question. I am setting up this project in my country, the ac voltage is 120v. then the DC volage is how much 220 dc so that the output can modify it to 120v ac.
@Wahyu Eko Romadhon
All your projects and videos are really interesting. Which video editing software are you using to make videos?
Adobe premiere
@@WahyuEkoRomadhon Thank you :-)
Hi, what is the maximum surge power and how many secs of surge power can it handle? Thank you
Hello again.there is a resistor named (sens) in this board what is that for and what the range of it ...in fact what is range for (sens) resistor in board for 24v...tanx.i dont know why i don’t have 3525 pwm pulse on my mosfet pins
Hai, Mengapa inti ferit menghabiskan begitu banyak arus DC? dengan beban dan juga tanpa beban? /// hi, Why is the ferrite core spending so much DC current? with load and also without load? /// ওহে, ফেরাইট কোর কেন এত ডিসি কারেন্ট খরচ করছে? লোড সহ এবং লোড ছাড়াও? /// Thank's!!!!
Mantap terus berinovasi untuk umat👍👍👍👍👍
Hi bro nice work! Can i ask a question?
Is it possible the shift the phase of the inverter?
Hello again.i made this project completely.
Now i have two problem...one-> my hi volt fet(23n50) near inductor start warming to hot with out any things connected for run or light(i use about 3mh inductor)
Two->when i connect a fan or light to out put 220vac start to down and then turn off and inverter module restarted.why?
All things start true and good and out put is sine wave good but i don’t know why that two problems happen!,,!
I use 24vdc20a power to run.
Can you help me to solve?tanx
Set UVP under 20V
yang stage pertama utuk switching mengunakan sistem buck bost converter / sistem phuspul untuk inverter step,up nya mas..?
Ha Ha Ha Ha, almost 80% persons who deals in electronics are smokers.
Now to the topic. Good project with almost complete details. Thumbs up.
Hehehe agree with you 😁,
Mantab.....ditunggu yg 5kw
Good Work brother
Hello sir thank you for all the videos you make sir pls make inverter 24v to 220v with two ee4220 Ferrite core
mas j gnd itu disambung kemana mas? kemudian Rsense nya berapa K ?? bingung aku iki
Can you please tell me what is the value of EMI Filter inductance
Vc é o caraaaaaa parabéns pelo projeto....
It draw a very high current on a input side I think the 50A fuse might be burn up.
Put twice
Hi. The schematic download section at the bottom of the page is not disabled and clickable. Check it if possible. Thankful.
Now check it
@@WahyuEkoRomadhon Hi. I checked again. Again, the schematic is not downloadable and cannot be clicked. Apparently it is possible to download.
Hello again.I try to made this nice project I’m on made ring fritte ...i used 2*4 turn for primary and 65turn for secondary and then i don’t know for two other out put how to turn ...i use 3turn and 3 turn again but when i connect it to board i have dc 380volt well but my 8 *fr207 start to hot so much and my step down module start hot much ...!!!
Use step down voltage external
Coba buat cdi racing mas
Bang bisa ga modif inverter high frequency 500watt jadi 1000watt atau 1500watt
Saludos sensei como siempre buen proyecto en inversores
wih mantap tenan, mas eko,, dan akan lebih jos lagi kalau ada penjelasan nama komponen komponennya dan penjelasan laiinya,, jujur mas suara musik nya agak sedikit mengganggu, mungkin akan lebih keren dan sangat bermanfaat jika suara musik itu di ganti dengan suara penjelasan jenengan dari semua aktifitas yg di buat,, ,, oh iya ada no contak atau wa kah,,sy mau konsultasi atau pesan barang barang yg sudah mas rakit..
Iy mas nnti klo sdah trsedia pcb sy gnkan bhs indo utk tutorialnya. Dn utk pmbelian pcb sya beri kertas panduan.
@Wahyu Eko Romadhon hello friend thanks for sharing your project. I have a question. I am setting up this project in my country, the ac voltage is 120v. then the DC volage is how much 220 dc so that the output can modify it to 120v ac.
Cant sir cause using egs002
@@WahyuEkoRomadhon I am putting together the same of your inverter project from 24v DC to 120v ac. I have to make the modifications to the voltages. My question for the step-up voltage of how much is it from 24 to 220v DC and 220 DC to 120v ac. my question if it is ok in the first stage. Thank you
Admin..How can I add IGBT to this design
Sir, can i use this with both 12V and 24V DC input,
Does this circuit haa short circuit, under voltage , over voltage protection,
I need more details about this
Yes it can bro, yes all fitur that u mean includes
Donat'e kayak'e enak enek susu ne😁😁
Mas Wer kapan2 bikin Inverter Hybrid...
Tapi ini udah sangat joss banget 👍👍
Hbis ni nnt mas. Hybrid dr pln didckan pke pfc buck boost. Di campur out dc step up. Bru diegs. Klo hbryd sinkron ac rumit mas
@@WahyuEkoRomadhon Ok mas 👍😁,,
Memang rumit sih,, apa karena kerumitan nya yg nyebabin harga Inverter Hybrid sangat mahal...
Mungkin mas. Tapi sbnere masih rumitan smps yg pfc fb mas dbnding invrtr hf ini.
@@WahyuEkoRomadhon hahaha 😁,, Klo SMPS FB+PFC saya masih agak bingung karena saking banyaknya komponen yang gak boleh asal-asalan 😁
Saya tunggu video2 selanjutnya mas,, suka pas pengujiannya👍😁😁
Siapp mas. Thanks jg udah mampir 🙏
Kalau beli sdh jadi di mana ya? Tolong infokan
mas eko itu lem apa ya yang dipake di toroid penasaran terimakasih mas
Klo gk ada totem nya rekom gk mas?
can i buy a pcb from you.
Sir what is this- fc-a2012bk-470h2 ?
The schematic pdf link plz❤
cool very good your work.
friend you have video of how to calculate the ferrite transformer ?
you can see previous dc to dc step up
Untuk menyuplay trafo 30amp 82vac mampu maksimal tidak bang?
Mas, tolong buatin tutorial membuat inverter dc to dc yang paling mudah. Soalnya banyak teman teman yang pengen bisa membuat inverter tapi masih pemula.
Iya mas siap
klo mo naikin daya main dimananya bang?
The fans are way to loud. If you mount a single much larger fan above the board cooling from above you could get silent running.
No its not silent fan .. still loud 🤣
mas bikin yang 7.1 channel donk.. yang 5.1 luar biasa sekali..
Not a fan of high and low inverter it's a cheaper way to build but now insufficient I love your work but I really like the building of low frequency only
kaget ada asap kirain ada yg kebakar,, ternyata asab uduut,,
Apakah anda menjualnya
Mas bro, resistor SENS itu dikasi yg berapa ohm??
Tumut nyimak mbah
Very professional
unboxing ngeri mas nganggo clurit. hehehe
Anti mainstrem mas kwwk
How to vind the transformer plz make a vedio
abang kuliah dimana
Sekalian nama teknik ny
Salut sama dgn ilmunya 😀
Jangan liat dari ilmunya saja tapi pengalaman juga wkwk, emang mantep mas Eko 🙏
@@bagustri6077 iya.. Pengalaman Nya Banyak Dan Luas 😃
saya yg cuma lulusan SMK
kalo masalh pengalaman elektro
jangan ditanyain. sy juga gak paham
hehehe
@@ekoby4543 saya Masih SMA 😂
@@ekoby4543 dari SD saya dah hobi dan pengalaman.. Sebenrnya kalo Bermain Kabel dan Kelistrikan dibawah 50V Dari Tk udh mampu hehe
Sir can u suggest me a charging circuit and auto cutoff circuit for this
Usingg 555
@@WahyuEkoRomadhon what about the changing circuit for charging the battry
Jijal gowo batrai abc mas😀😀
Inverter nya bisa di modifikasi menjadi 2000watt
Schematic of no quality circuit for download.
And if the meaning in the downloads section is the schematic download section is disabled. Thanks if you put the schematic of the circuit.
Oh inthe bottom of page
@@WahyuEkoRomadhon It is at the bottom of the page but cannot be clicked. Gerber and file parts are clickable.
Mas coba buatin power ampli mengunakan lc7161n
Rumit..... Tapi berhasil.... Mas eko emang gene 👍👍👍
Wah ada Bli Agung juga 😄Dari Bali Ya Bli
@@electroniccreative7683 ya betul mas..... Hobby nyolder juga
@@agungoka482 mantap.. Saya deketnya Monang maning.. Deket SMPN7 Bli 😃
mas, bisa ga minta frequency outputnya 200hz?
Kalau mau beli dimana mas
Masuk pak eko 😋
Apkah ini djual di lapak omline??
Untuk mndPatkan produk ini beli lapak apa mas???
Sperti video mas ada
Hello bang ,apa abang jualan pcb nya ?
Keren Mas
Keren abis dah
Very nice
Excelente !
Bisa minta no untuk dihubungi mas? Mau nanya2
Pengen beli yang udah jadinya mas bisa??
Yang tinggal pakai ada g mas 😀😀
Idle current besar sekali gan, 4A ya?
0.7A gan
Telat mas wahyu
Mas.iku seng lek mu bukak kerdus pcb ngo opo
Wkwkkw
Mantapp
Good
Ditunggu jual pcbne mas..msti ketinggalan info
Iya mas siap
Mas mau tanya pesen driver sampek brp
Lem nya pakai lem apa mas?
Pake lem ap ya pak. Di merk tulisannya china. Sprti pasta hetsink tapi bisa buat lem.
Jarang bngt di lapak2 online pak. Klo mau sy krim kan via fb fto lemnya
@@WahyuEkoRomadhon coba di kirim mas.
@@Spesialis_Programmer_IC_Memory heatsink plaster, biasane dipakai komputer built up
Kalo udah jadi kisaran berapa om?
blm djual mas
Harga
mantab
keren
mantull.. test nyalain ac mas 🙏
G pnya ac mas wkwkwk. Beban yg berat yg sy pnya heatgun itu mas max 1.8kw
up lagi dong , sampe 90 persenan efisiensi nya. hehehe
Bisa mas hrga jd lbih mahal. Tggal gnti bbrpa part. Efisiensi diatas 80% sudah bgus. Epever yg dbwah 90% 1kw psw hrga sktr 4jt an.
@@WahyuEkoRomadhon abis berapa tuh modal nya ?