How to Design and Simulate Inset Feed Microstrip Patch Antenna using CST Studio | AWP Lab Tutorial 8
ฝัง
- เผยแพร่เมื่อ 20 ก.ย. 2024
- Hello Everyone!
Welcome to the world of 110 Engineering!
Basic purpose of this video is to help the students and researchers to learn the the design procedure of inset feed microstrip patch antenna using CST Studio.
Following Terms have been explained in this video:
Part 1: Introduction to Micro strip Patch Antennas
Part 2: Parameters Calculation for the Design of Micro strip Patch Antenna
a) Calculation of Length and Width of Patch (By using Calculation Formula and online Method)
b) Calculation of Width of Feedline in order to match input Impedance of an Antenna (Online from CST)
c) Calculation of Length of Feedline (By using Calculation Formula and Online from CST)
Part 3: Design of Micro strip Patch Antenna using CST
Step 01: Design of Ground
Step 02: Design of Substrate
Step 03: Design of Patch with Inset Feedline
Step 04: Waveguide Port Excitation
Part 4: Simulated Results of Micro strip Patch Antenna
a) S Parameters / S11 / Return Losses
b) Gain
c) Directivity
d) Radiation Pattern
Like, and subscribe 110 Engineering for learning more technical tools and advanced software.
If you have any questions or need guidance about anything, just comment below in the comment section.
Thanks for watching.
Regards
This video is only for educational purpose. Copyright Disclaimer under Section 107 of the copyright act 1976, allowance is made for fair use for purposes such as criticism, comment, news reporting, scholarship, and research. Fair use is a use permitted by copyright statute that might otherwise be infringing. Non-profit, educational or personal use tips the balance in favour of fair use.
Thank you!
MashaaAllah you have explained it in depth. Now i can design a patch antenna for my 4G wifi device.
Thank you.
You designed Microstrip patch antenna with complete practical concepts. Thank You.
You covered all the things in a single video. Best video for Microstrip patch antenna design.
it is the best tutorial as much i have seen ever, thank u very much.
Thank you dear.
You cleared all the basic concepts due to which I was confused while designing microstrip patch antennas. Thanks a lot sir.
You discussed all the basic concepts in a nice way. Thank you.
Marvelous explanation of design in all aspects.
Great vid..btw how did u get the Zmax?at 14:06
Yes continues good bro
Best lecture sir
Good work. keep it up dear.
شكرا جزيلا على الشرح المفيد
👍
Maha Allah sir ggg.......Great work
mashallah nice work 👍
Good work.
Very good work
Good work
Amazing video
How to find the height of the insert feed? you have given it as 1.2
thanks for this explanation: i have question >> what is the rule follow to calculate inset length and width
Great
thanks for the useful tutorial
Good work bro keep it up 💖💖💖
Nice vedio
Very nice 👍
Mashallah ❤️🌹❤️
Good
👍👍❤❤
Sir how did you calculate the length of cut and feed line
you are doing a great work bro. Please make a tutorial on how can we integrate metasurface and antenna, thanks
Sure, I will upload a tutorial on metasurface antennas asap.
@@110engineering looking forward to it, thanks Sir
Hi, thanks for the Video, it helped me a lot in my research. At the beginning of the video you show a manual document. Could you tell me where I can see you better?
Thanks. How can I share it with you?
@@110engineeringhello can you share with me pleasee ?
@@kubilaykalkan54 please share your email address
hello sir thankuso much for this video ..sir can u help us making microstrip patch antenna as radar system
in advance design system
you said the length of the feedline is 14.52 mm but on the screen, we are seeing 14.58 mm can you explain why ?
👍
Nice vedio