how to make use Load Cell sensor with Arduino Uno

Download the code here:
github.com/pas...
Download the zip file here;www.arduinolib...
Music in this video;
chill. by sakura Hz / sakurahertz Creative Commons - Attribution 3.0 Unported - CC BY 3.0 Free Download / Stream: bit.ly/chill-sa... Music promoted by Audio Library • Chill - sakura Hz (No ...

[@theallroundershow576]

Which type of jumper wire did you use???pls reply

[@passiontechklm]

Any types of jumper wire you can use ,I use here male to female 20cm jumper wire.The important is to transfer the data and power only.

[@footwork.frenzy]

Is the code ready to use?

[@rar9119]

Does this sensor work with Raspberry pi microcontroller or is it only compatible with Arduino?

[@passiontechklm]

It's competitable with Raspberry too.

[@rar9119]

@@passiontechklm Thank you 🙏

[@dheyaakadhim8375]

Thanks so much. How can we write those loads on excel sheet??

[@abhaychaurasia8576]

Was this load cell used immediately after purchase or was it used after calibrating it?

[@madhumaytripathi4216]

zip file is not included in description

[@passiontechklm]

Please check in description I already give link

[@urvish6649]

Thanks brother

[@tsalazar3289]

Can this set up be done without a laptop? Or is the laptop the power supply to the display?

[@passiontechklm]

Laptop is to upload the code only, after done upload the code you can remove the laptop and power Arduino by other power supply between 5 to 12vdc.

[@nazmulalam3108]

cannot measure 200 kg load cell

[@harikrishnanharikrishnan6074]

Which type of wires are used to connect this ?

[@msrutujapatil1787]

During uploading program it shows error occurred while uploading the sketch.
What exact meaning of this error .
I checked port many times . Please replay me

[@PavankumarBatchu-b8m]

we want to measure the weight of the backpack. Can The load cell sensor that you used in the video be able to give the weight of the backpack in kg(kilograms) i.e., up to 10-120kgs.? Please reply.

[@Aishwarya_06]

Please Provide Circuit Diagram AS Soon As Possible

[@zohairdilawar116]

How do we trf this weight displayed to Google sheets

[@jmch1369]

Thank you,,,

[@Aishwarya_06]

Please Sir Provide Circuit Diagram As Soon As Possible

[@aiii73]

Have u done project?

[@aiii73]

Plz reply bro

[@humayunjawed7751]

What is the component behind the lcd display?

[@passiontechklm]

I2C or build in i2c LCD display

[@aiii73]

Circuit diagram plz

[@syednizarwannoh1099]

Can i connect Any coloured wire of load cell into the hx711? Let's say i connect the red wire to E- is there any difference?

[@africantech5]

Yes

[@Mannuyadav567]

Fatal error: failed to connect to esp8266 time out

[@mariahhafizah5208]

While upload sketch, when it say connecting... u should press hold the boot button on esp8266 . Release the button after it done

[@NWONKNU273]

What about the calibration factor ??how do you get that value?Will they change for different objects or stays constant

[@z3r0rvm19]

Calibration factor can be determined by performing Calibration. It can be done by going into the examples folder then under the HX711_ADC folder there is an example called calibration. Read the instructions carefully and perform it, at the end it will show you a calibration factor which can be used here.

[@NWONKNU273]

@@z3r0rvm19 thank u🤗

[@yusufbyahatti1552]

after calibration program how to dump this program in arduino

[@duangjunthanikkul9487]

@@z3r0rvm19 0

[@abdulazizshaikh7598]

Any one please help me out, after connecting all the components. In LCD display this one indicates = IV DOSED ( ML)
If any one know about this please help ke

[@sushmithamoguloji1155]

Provide zip file

[@passiontechklm]

Please check in description I already give the link