It would be good to see a closeup look as to how the receiver is connected to the Sabertooth. Is a battery pack required? Also conventional 3 pin servo cables?
Are these worm type gears inside the gearboxes? Without the brakes if these were installed on a powerchair/wheelchair would it coast a little when electric power is removed abruptly from full power with someone lightweight sitting on it? I'm trying to find out if I can use them on a model locomotive I'm building. I need them to coast when power is removed without the solenoid type electric brakes installed. Like a RC car with a pinion and spur gear on it. Thanks...
how do you test them on a chair where you cannot take brakes apart? how much voltage and which wires go where,do those have brushes? you gonna take em apart?
Hello can you help me? I have the same controller BUT When I turn it on, the motors run always one sometimes alternately without contact with the recipient This also happens with a connection to the receiver
do you think that sabertooth 2x32 motor driver would drive 4 total motors? or would I need 2 motor drivers? I am making a slope mower and it needs to pull a hill with ease. thanks
With a complete battery powered wheelchair, how do you add the sabertooth into existing wiring and still have full use of built in wheelchair battery charger?
I commented before watching the entire video. My apology. I do want to know if the batteries are deep cycle. I have two 12 volt 12 ah batteries...is there a major difference?
Cool. That what I’m looking for a similar setup . I have two hoverboard Motor with two 350w Motor Controller . I have a Ppm receiver from a rc helicopter . Will it work if I just connect the receiver with a throttle signal ? Or how should I connect it ???
Great video especially your dip switch setting off, on, off, on, off, on
clear explanation great work
Really good video information thanks for the info 👍
Well done. Can you make just one motor the right or left turn. Please let show. Thanks so much.
great explanation
It would be good to see a closeup look as to how the receiver is connected to the Sabertooth. Is a battery pack required? Also conventional 3 pin servo cables?
Can you run 4 of those motors from one motor driver
What tires do you use for these jazzy motors? I've been looking for these wheels for this motor and I can't find the right size
its great work
i need to know how the break system works can you guide me how to release and apply break
Hi could you explain why you removed the brakes?
Great work!
You show us forward/backward and left/right, Whats about forward or backward + steer?
please can you share motor and motor drivers you have used
Could you please share the motor brand name or the specifications used here? It would be really helpful
I would like to know also
cclmotors.com/public/assets/common/images/product/product/product-46/spec.pdf?1620198099
Are these worm type gears inside the gearboxes? Without the brakes if these were installed on a powerchair/wheelchair would it coast a little when electric power is removed abruptly from full power with someone lightweight sitting on it? I'm trying to find out if I can use them on a model locomotive I'm building. I need them to coast when power is removed without the solenoid type electric brakes installed. Like a RC car with a pinion and spur gear on it. Thanks...
How turning systems works in remote, both motors runs opposite way.
how do you test them on a chair where you cannot take brakes apart? how much voltage and which wires go where,do those have brushes? you gonna take em apart?
Hello
can you help me?
I have the same controller
BUT
When I turn it on, the motors run
always one
sometimes alternately
without contact with the recipient
This also happens with a connection to the receiver
Did you ever figure out what was causing it? Mine will do that at times
Hello do I have to use that type of remote?
DOES ANYONE KNOW HOW TO WIRE UP 4WD RC LAWNMOWER
Have you done a voltage leak test on the 2x32?
do you think that sabertooth 2x32 motor driver would drive 4 total motors? or would I need 2 motor drivers? I am making a slope mower and it needs to pull a hill with ease. thanks
Can we use LiIon batteries on this? More power density?
I want to order this circuit. Recommend how to order i live in thailand
How to adjust rc transmitter or received ...? Make vidio
I am having trouble with that, also.
Where did you get the remote control?
Which type of motors used in this video
Madhu vajrakarur they are from a jazzy wheelchair if I remember correctly
With a complete battery powered wheelchair, how do you add the sabertooth into existing wiring and still have full use of built in wheelchair battery charger?
Google sabertooth 2x32 image.
I commented before watching the entire video. My apology. I do want to know if the batteries are deep cycle. I have two 12 volt 12 ah batteries...is there a major difference?
I believe these are the ones I am using or very similar. Seem to work great. here is the link . amzn.to/2FrtsJ4. Thanks
they are gel cell only to be charged by a 5 amp charger takes a long slow charge
Cool. That what I’m looking for a similar setup . I have two hoverboard Motor with two 350w Motor Controller . I have a Ppm receiver from a rc helicopter . Will it work if I just connect the receiver with a throttle signal ? Or how should I connect it ???