ฝัง
- เผยแพร่เมื่อ 7 มี.ค. 2018
- Sorry friends..... """":::: I am using circuit diagram is not correct in video..... please
check this link for correct and complete information ::::: """"
::-- circuit diagram :-
Clap Switch :- amzn.to/3KYTNQU
If you enjoy my videos please Subscribe! - แนวปฏิบัติและการใช้ชีวิต
Nice video but guess what happens at a birthday party then disco 🤣
😂😂😂😂😂
😂😂😂
What about honeymoon 😂😂😂
@@prabhdhillon3638 😂😂
😂😂😂👌👌👌
Thank u for this video ,I am searching this type of simple circuit since long time....Keep it up👍
اويلي يابة...
العدة والغراض مالته الا يموتن😍
Thanks for this project idea 💡💡 nice 🙂
Detailed working : -
Working of a clap switch
Working of a Clap switch: -
1)Condenser microphone takes i/p as sound of
clap and gives electrical o/p. This o/p though
is very small. Hence, we need an op amp. to
amplify this electrical o/p.
2)Here, o/p of condenser microphone is given
to the 2nd pin of IC 741. Therefore, it acts as
inverting op amp. Amplified o/p is generated
at pin6 of the IC.
3)The amplified o/p is then given to IC 4017.
IC 4017 is a decade counter IC. Means it can
count 10 numbers or 10 i/p.
4)Pin configuration of IC 4017: -
In IC 4017, pin no. 14 is a clock i/p pin. pin no.
1,2,3,4,5,6,7 and pin no. 9,10,11 are o/p
pins. Pin 13 is clock enable pin. Pin 12 is
a carry out and pin 15 is a reset. Pin 16 is
+Vcc and pin 8 is ground.
5)Working of IC 4017: -
To work the IC i/p must be given to pin 14 of
the IC. And pin 13 must be grounded to enable
the counting. Pin no. 12 also must be grounded since
carry o/p is not used. The counter increases with one
for every rising clock pulse and enables its
10 o/p one at a time. After the counter reaches
9, it starts again. When the 1st i/p is given to the
IC, 3rd pin i.e., Q0 gives high o/p. When 2nd
i/p is given, 2nd pin i.e., Q1 gives high o/p.
When 3rd i/p is given, 4th pin i.e., Q2 gives
high o/p. And enables it's all 10 o/p one by one.
But when Reset (pin 15) is connected to
any of the o/p, it counts till that o/p only
and resets the whole IC. Here, pin 15 is connected
to pin 4 (Q2). So, after 3rd i/p given, instead
of giving high o/p at pin 4 (Q4), it resets
itself and starts again from Q0. And hence
o/p keeps switching between pin 2 and 3 (Q1
and Q0).
6)Now, this o/p generated across pin 2 and 3
can be used as switch. From pin 3, and LED is
connected and from pin 2, o/p is given to relay
to control the bulb. But, o/p generated across
pin 2 is not sufficient for relay to act as
a switch. Hence, a transistor is used to
amplify the o/p. Here, a NPN transistor is
used. When o/p from 2nd pin of IC 4017 is given
to base of the transistor, voltage is generated
across base and emitter, and transistor is in
ON state. When o/p is generated across 3rd pin
of IC 4017, 2nd pin gives low o/p and hence
transistor is in OFF state.
7)Now, this o/p generated from the transistor
is given to the relay. Relay is a mechanical
switch in which a coil is used to operate the
switch. When voltage is generated across the
relay (i.e., when transistor is in ON state)
coil produces magnetic field and attracts
the magnet of the switch and closes the switch (NC).
When, current stops flowing through the
magnetic field (i.e., when transistor is in
OFF state) is coil loses the magnetic field
and switch turns back off (NO). This switch can be
used to switch ON/OFF the AC supply which is
given to the bulb.
When the current passes through the coil, the coil
gets charged. When current switches OFF, the
coil loses its magnetic field and produces
back emf. This back emf can damage the entire
circuit. Hence, a diode is used in reverse bias
to stop the back emf.
This is how clap switch takes the i/p from
a microphone and uses it to control a bulb,
a fan, a radio, or any electrical device which
works on AC.
Make sure to like if u find this helpful 😊
Is it switches off automatically after sometime? Or goes till Next clap..
amazing 🤩
@@relaxlofi557 It doesn't switches off autoatically....you have to clap to switch it off
@@relaxlofi557 bro go live
Brother I do made this circuit 2 times but nothing is happening, I am unable to understand how transistir's opening and closing will provide current in the collector of transistor I mean there's no source in collector right? If some voltages reach to base, it will open base-emitter junction, but do any current goes up to collector too? 🤔
If you explained it how it works. It would be fantastic
Nice video sir...
Had to make a few modifications, but its working perfectly.
Hey! Would you by any chance know how to amplify the mics sensitivity?
well done , very excellent you have left to describe 7pin IC value.
El problema es que tengo un vecino dedicado al espectáculo y la gente aplaude mucho. Ya me han fundido varios focos con este circuito.
🤣🤣🤣🤣 Usa un interruptor. Manténgalo apagado cuando su vecino haga un espectáculo.
Sir this is active low or active high pin
Super bro, this is used for my science fair project
Can u tell me how you do shouldering plzz😢
Vera level 👏👏👏👏
Telugu language nidhii
I try this. It is my science project for science fair in my college thank you
Do you have circuit diagram pls tell 🙏🙏
Bro, i have made as per your given circuit in the description for my phy project, but, unfortunately, when i connect the battery, if red led glows, then green led will on when clapped. But once green led is on, the red led cannot be oned again by clapping. Can you please help me with any common mistakes nd all?
Nice build. You could also have used the 4013 dual D Type Latch in Toggle mode
Heyyaa HOW DOES A NEON LAMP WORK ??? WHAT ARE GAS DISCHARGE TUBES AND WHAT IS NEGATIVE RESISTANCE IN NEON LAMPS ?th-cam.com/video/g01ovsm-Pd0/w-d-xo.html
WATCH THIS AND FIND OUT !!!
Sir ager 12 v ki relay lgade to kya component same rahenge??
Nice one,thanks.
Sir can you explain the working principle
Of this circuit
شكرا لك احسنت
thanke you
good. ♡♡♡
Nice Video, very helpful
Buth acha project bunaya ap ne well done
Muito bom mesmo muito interessante de mais da conta valeu
Which components do you use????
Super bro❤
......i hope i would make this project sir bcz i show me one project based on ic so I think this is good..👍
Could you give me some advice for electronic beginner pls?
Where did you get the container for components? Thank you.
May we help you?
What are the names of the instruments given to do the experiment
This looks like magic..
Damn He Really Does Know How To Clap
Hi sir how to connect 1k variable resistor in this circuit diagram it has 3pin....?
I have a 6v Relay .. can i use a voltage divider in the relays input side to drop 3 v accross the register?
Yah bro u can
Chala bagundi ❤🎉
Very clear vedio....tha nks
So nice
so did he program the controller that he put? I thought you always need to program them, by using arduino or something else maybe...
He used a 4017 decade counter. When the Op-Amp goes high it clocks the counter which then cycles through switching on the transistor and LED
Is it one type of hardware project?
I wanna know if we can connect the clap switch to the bulb for longer time..as usual how we use at home like continuous for 5-6 hrs..plz reply
What about other sounds like a shut the door? How did you filtr similar noices?
Sir please mention name with each apparatus.
Thank you
741 and 4017
@@vikiTech000 bhai video mein btaya nhin 741
Sir plzz tell me in which direction i would solder components because i am bignner
Very nice video sir ji
Please clear followings droughts
1)The variable resistance is of 1K or 10K. Circuit diagram in Video says it will be 1K where attached diagram says it will 10K.
2) Same is with the resistance R1. Is it of 1K or 10K?
3) 22K is used in both circuit diagram but it is neither mentioned in the video nor in the list of items.
Sir....sorry i am busy in my office work for last year....check again in Description Box for complete information
@@vikiTech000 sir action nahin samjha
@@shrijit959 ......after long time working again on youtube
in circuit diagram mention 470ohm resistor but not in video
@@kavindukulathunga2406 bro...circuit diagram is correct
Plot twist:
Book fall from the table bulb 💡 turns on
Mosquito in the room bulb is on blinking mode
sir yadi 12 v relay use kare to 12v power supply use krna padega kya
sir u r genius
Sir ,in first process (without light bulb) there is any requirement of relay. if I will connect without relay , the circuit Will working or not?
yes...its work
@@vikiTech000 ok Sir
@@vikiTech000 does it work
@@vnagaraju1216 yes...
Thank u bro! Thank u bro!Thank u bro!thank u bro!Thank u bro!Thank u bro!Thank u bro!Thank u bro!Thank u bro!Thank u bro!Thank u bro!Thank u bro!Thank u bro!Thank u bro!Thank u bro!Thank u bro!Thank u bro!Thank u bro!Thank u bro!Thank u bro!Thank u bro!Thank u bro!Thank u bro!Thank u bro!Thank u bro!Thank u bro!Thank u bro!Thank u bro!Thank u bro!Thank u bro!
Good job my friend keep it up ❤❤❤❤❤❤
thanks bro
Bro plss batao 4017-1c ke sath vo black colour ka chotta sa kya ha
Please circulate example again
And product list send me please....
Super bhai
thanks
How did you take input sir . And variable resistor third mid terminal where you was connected
Good work
Sir can you send the block diagram of this project
Bro is it possible to use 5v relay and 10k variable resistor...pls rply bro
Heyyaa HOW DOES A NEON LAMP WORK ??? WHAT ARE GAS DISCHARGE TUBES AND WHAT IS NEGATIVE RESISTANCE IN NEON LAMPS ?th-cam.com/video/g01ovsm-Pd0/w-d-xo.html
WATCH THIS AND FIND OUT !!!
Fabulous👆
How many ac current at the relay on pcb will flow? because got 240vac go through the pcb board to connected with terminal block. the current will limited because of pcb?
Do you have the methods how todo on the board with the resistors and etc?
Heyyaa HOW DOES A NEON LAMP WORK ??? WHAT ARE GAS DISCHARGE TUBES AND WHAT IS NEGATIVE RESISTANCE IN NEON LAMPS ?th-cam.com/video/g01ovsm-Pd0/w-d-xo.html
WATCH THIS AND FIND OUT !!!
if circuit work with mic , i think relay will damage because it don't detect clap , if have big sound is relay will on/off
sorry for my english
Same my problem
Its not working
Vũ Trần mn
Mind blowing
Really it is good
Sir pls tell the connections in pcb board how can we understand .....
He showed a schematic. You don't have to do it on a PCB just do it on a breadboard.
Sir toda explain bhe kar dete to Accha hota...
Really
Kya explanation chahiye, circuit vision website par Likha hua hai
Good very nice video
Where Did You Buy That Resisters And Transisters
sir, you didn't shown how to connect the circuit?
Please sir
,
Hey HOW DOES A NEON LAMP WORK ??? WHAT ARE GAS DISCHARGE TUBES AND WHAT IS NEGATIVE RESISTANCE IN NEON LAMPS ?th-cam.com/video/g01ovsm-Pd0/w-d-xo.html
WATCH THIS AND FIND OUT !!!
just follow the schematics
Bro can i know why it is working only for clap sounds... Is it? also work for any sound...
Can you please suggest solution...
Thank you
It works for all loud sound, sound is the trigger,
Bakwwas Ka question pocha hai yar
It is possible that circuit accepts sound frequency of clap, we can't explain exactly as we have not research on it, thank you
NICE Project
Could we use 5W LED bulb
Don't use filament bulb it will gon easily dew to flickering......use CFL
That Only testing filmet 💡
Bro, you have not showed how to connect the circuit.
yeah absolutely..
Circuit batayo
U should follow diagram
I want to buy this what will be the cost
Circuit kese bnayenge kese connect krenge btaoge tb n
Thank you 😊
Why should you use variable resistance
I want to know the materials used in this can u plzzzz say the name of the materials
Heloo there MAKE YOUR OWN SPIRAL LED LAMP FOR DIWALI DECORATION!!
th-cam.com/video/mj__UR6s0z8/w-d-xo.html
Hlo please reply as soon as possible I want to make this project and I have to submit it tomorrow.....
Actually I want to know the joins from back side can u please send me the picture of back side that will be enough.....
Pls reply as soon as possible
Creative... When clapping for Happy Birthday, this idea can use
Is that 1k variable resistance compulsory..
Is the 12th pin of the 4017 connected to the 13th pin and the 15th pin to the 4th pin.
bro check again in Description Box for complete information
plz. Tell me the cost of all the things that you have used
50-100 INR
Great wala experiment he
Ossume bro
It will be shame while doing secret work if someone clap outside. Light will be on ...sab log dhekeka...
😂
Dutch:
lol!!!!! very funny my friend
What are those things u r using... Doesn't they have any names☹️
Do you have a online shop I think for electronic stuff
Nice video sir.
Lekin vidio ke sath aap instructions bhi diya kare aur diagram ko aur behatar banake dikhane ki koshish karenge to hamare liye samjhanemain aasani hogi.
bhai agar aap ise thoda detail me sara programming krte to jada samajh aata
ok....bro i try in next time
th-cam.com/video/8sGKH3gElD0/w-d-xo.html
@@vikiTech000 Sir i need your help. 8 no. pin (IC 741) connected to GND on IC 4017?
Sir you can send me list of tool of equipment
Hey HOW DOES A NEON LAMP WORK ??? WHAT ARE GAS DISCHARGE TUBES AND WHAT IS NEGATIVE RESISTANCE IN NEON LAMPS ?th-cam.com/video/g01ovsm-Pd0/w-d-xo.html
WATCH THIS AND FIND OUT !!!
Can we use 5v relay
Very nice
Can i use 6v relay?
yes
Can you please show us the connections ..we are having trouble in understanding because of its circuit complications
Ap noob ho !! 😆
Circuits tar explain dorkar.. Kivabe connect korecen exaplinly arekta vedio den please
Can I use mini relay. Please reply me...
i really want do it but i scare when i clap my hand my whole house blow up.
HahaH
Sir where to buy this electronic components?
If you want I can send you
@@Ajeetsingh30507 how
@@agranidixit1030 7042581947 number. For Info.
Does it only works on clap or also loud sound
Selalu yg terbaik, bisakah untuk memakai lampu LHE
give the name of components you have used.
Hey HOW DOES A NEON LAMP WORK ??? WHAT ARE GAS DISCHARGE TUBES AND WHAT IS NEGATIVE RESISTANCE IN NEON LAMPS ?th-cam.com/video/g01ovsm-Pd0/w-d-xo.html
WATCH THIS AND FIND OUT !!!
This is for 220v?
With 220V how much time will it work?
The project is not working. What can i do? Please reply
What's your problem