Einhell TC-BD 630 drill press UNBOXING, ASSEMBLY, TUNE UP, REVIEW

Einhell TC-BD 630 is excellent drill press. Very powerfull 630w motor and 12 different speeds from 250rpm to 2450rpm. You can drill anything with this machine, i´am very pleased.
------------------------------
Adventures by A Himitsu / a-himitsu​
Creative Commons - Attribution 3.0 Unported- CC BY 3.0
Free Download / Stream: bit.ly/2Pj0MtT​
Music released by Argofox • A Himitsu - Adventures... ​
Music promoted by Audio Library • Adventures - A Himitsu... ​
------------------------------
best buget drill press

[@erefafir6760]

This press has worked like a charm for my projects th-cam.com/users/postUgkxajoEbapTfqWaadnqb04h6U576yxXp-FE . I didn't even secure it to my table top, mainly due to the fact that I was using a 15 lbs drill vise. It's not flimsy at all as to what others have claimed it to be. Make sure the locking nuts and levers are secured and there won't be any issues with light pressure and patience. I was able to drill through aluminum, plastic, and steel (steel took a while) with no problems at all. Yeah it took a little longer than a regular drill press, but I don't have the space OR the money for one.The instruction manual was worthless, but luckily assembling the press was intuitive. However, the manual would be good for ordering replacement parts if needed. There is a nice breakdown of the parts that are included in the kit. Before ordering, make sure it is compatible with your unit, it is clearly stated what models the press is compatible with.This was an excellent purchase for $40!!

[@tomspeed2000]

Thank you very much , without your video was too hard to be understanding, no single manual was in the box..still I have problems to changing speed, those 2 straps are too tight, almost impossible to put them in the different gears..i will set them in low RPM and I think I won’t touching them again

[@marinajackson2363]

you will need to change the speed depending on the drill diameter, you can't just use one speed all the time unless you will use only one drill (the right one) all the time

[@corenting7343]

For those who are in this same situation.
First you need to unscrew the motor with two screws on each side.
After that, start moving the stap that need to be on a smaller gear, just force it out of his ring while turning. The strap will be loosen after that. Move the other part of it on the gear, forcing it into the gear while turning the gears.
Screw the motor to tighten the strap system
Hope it helps

[@r3plik4]

Don't use gloves beside standing drill!

[@trobert132]

Confirmed, it happened to me once. I was lucky that the gloves were already torn, but almost broke my wrist..

[@catalinp9176]

wd40 is not a lubricant. Is Water Displacement 40.

[@konstantinosvas7130]

WD it's perfect for aluminium...

[@walmorx]

Grazie! molto utile!

[@thijs3514]

Wauw, I like the review and the machine looks very nice! Are you still happy with it?
Thanks for sharing!

[@bekidiyprojects8889]

Machine is great, you can see my other videos. Im using this drill and im very pleased with no issues

[@HSebastianSosa]

Muy bueno el video, me sirvio para poder armarlo. Gracias !!!

[@juanpedrogarcialopez2599]

Me gusta el vídeo 👍😁

[@enverenergiaverde3693]

como le vas a dar a una herramienta de presicion directamente con el martillo.

[@javierortega8024]

Hay taladros de esta marcay modelo en MÉXICO??!??

[@guillermoabelgallardoaguer2246]

Please I need help, I can not start it even electric connection is ok, is there any trick?

[@mivancic5074]

Da li stolić na kojem se buši ima progib kod primjene veće vertikalne sile bušenja i koji je najveći provrt u čeliku koji si bušio?
Hvala

[@bekidiyprojects8889]

Ima nesto sitno savijanja, al to sam rijesio autodizalicom koju stavin pod stolic i kako podesim razinu stolica tako dignem autodizalicu do stolica da se nemoze savijat. A nisam nista prezahtjevno busio, 12mm ide lagano u 10mm celik, a konusno svrdlo 32 probija 3mm stjenku cijevi....