Hall Effect Sensor A3144 hall sensor

แชร์
ฝัง
  • เผยแพร่เมื่อ 17 ต.ค. 2024

ความคิดเห็น • 53

  • @bikerboy3k
    @bikerboy3k 2 ปีที่แล้ว +4

    This is the best video about hall sensors. No nonsense.

  • @studywithvc0
    @studywithvc0 3 ปีที่แล้ว +4

    Lage rho....achhi video hai...👌👌

  • @duvvurirajkumar6489
    @duvvurirajkumar6489 2 ปีที่แล้ว +2

    Sir my access125 converted electric scooter 67v 800w hub motor
    But recently hall sensor defective sir
    N41 909 This hall sensor not available in market so any alternative is suitable
    Give me replay sir thankq

    • @innovationic
      @innovationic  2 ปีที่แล้ว +2

      Generally hub motors have same sensor you can go for A3144 or any 3 pin Hall sensor

  • @bikerboy3k
    @bikerboy3k 2 ปีที่แล้ว +3

    How to choose what resistor you need for leds for example and how to make sure it doesn't block too much current?

    • @innovationic
      @innovationic  2 ปีที่แล้ว

      first you know the voltage and current rating of led then simply use [R = V/I] to get right value of resistor.
      For example if your led is Red 5mm then
      R = 1.8/0.01
      so resistor should be around 180E thats it....

  • @procompunet
    @procompunet 8 หลายเดือนก่อน +1

    agradezco su tiempo en ayudarme con un reemplazo del sensor Hall de mi moto que tiene REF: H-413F consigo en mi ciudad la RF: 41F lo podre utilizar gracias

    • @innovationic
      @innovationic  8 หลายเดือนก่อน

      most welcome

  • @mmw78
    @mmw78 ปีที่แล้ว +1

    Excelente 👌 explicación

  • @MikeysLab
    @MikeysLab ปีที่แล้ว +1

    Does anyone know the sensing bandwidth of the A3144, I would like to use it as a tach for a bldc motor, which is 920 kv running at 12V and has 14 permanent magnets, as such it should pulse around 2.5 kHz. Can this little guy move that fast lol

    • @innovationic
      @innovationic  ปีที่แล้ว

      this can handle upto 10KHz pulses and with proper driver circuit a3144 can rotate fast enough speed

  • @alchemy1
    @alchemy1 2 ปีที่แล้ว +1

    I am using this hall sensor with an N channel Mosfter IRFZ44N to run a make shift pulse motor.
    I am connecting the hall's output to the gate of the FET and also with 1K resistor to the supply.]
    It works. But when the magnet passes the hall, the FET turns off.
    How can this hall be wired so the FET turns on when the magnet passes by it?
    Wiring this with an NPN mosfet, its ouput causes the FET to go off when the magnet passes by with the way I have it. I like the opposite to happen if that is possble.

    • @innovationic
      @innovationic  2 ปีที่แล้ว

      When you passes magnet A3144 sensor give negative output (if you want to turn on mosfet when magnet passes through A3144 sensor) so you need to use connect the output of A3144 to PNP BJT like BC557 then connect MOSFET gate with 10K pull-up with GND.

    • @alchemy1
      @alchemy1 2 ปีที่แล้ว +1

      @@innovationic The hall output to gate of BC557 and then connect the gate of a PFET to where besides it's gate to the 10K pull up ( or pull down) to the ground?

    • @innovationic
      @innovationic  2 ปีที่แล้ว

      Sorry it's pull down 10k resistor to GND

    • @alchemy1
      @alchemy1 2 ปีที่แล้ว

      I need to connect the PFET to the BJT also. Is this correct otherwise they have no relationship between the two, beside the resistor to the ground ( which its drain also the drain of FET goes to). So do I hook up the gate of the PFET to the emiiter, the collector, the base of the BJT unless there is something else here I am missing?
      And does the 10K resistor connects to the ground or does it really connect to the +VDD where the source of the PFET goes to?

    • @innovationic
      @innovationic  2 ปีที่แล้ว +1

      Wait I make video in few minutes

  • @StefanoZamprogno
    @StefanoZamprogno ปีที่แล้ว +1

    3.3v alternative? thanks!

    • @innovationic
      @innovationic  ปีที่แล้ว +1

      I have tested that A3144 works from minimum 2.78v and at 3.3v it works pretty well

    • @StefanoZamprogno
      @StefanoZamprogno ปีที่แล้ว

      @@innovationic great thanks!

  • @georgesoare7937
    @georgesoare7937 2 ปีที่แล้ว

    Hy, i have a question, can you tell me how can i connect a loudspeaker to a hall sensor in order to be able to control volume. The loudspeaker have digital volume control. Thank you in advance for your answer

    • @innovationic
      @innovationic  2 ปีที่แล้ว

      you mean to control volume using hall sensor via magnet

    • @georgesoare7937
      @georgesoare7937 2 ปีที่แล้ว

      @@innovationic thank you for your quick answer. Yes, i want to control loudspeaker digital volume with Kick Scooter TF-100 Display hall sensor. Can i connect directly to the 3 pins of the hall sensor ? or should i connect on the board?

    • @innovationic
      @innovationic  2 ปีที่แล้ว

      digital volume control in your loudspeaker the volume nob is potentiometer or rotary encoder
      according to your system the hall sensor would connected

  • @robindion7724
    @robindion7724 8 หลายเดือนก่อน +1

    Resistor Value ?

    • @innovationic
      @innovationic  8 หลายเดือนก่อน

      120Ω resistor

  • @toewai-on2wr
    @toewai-on2wr ปีที่แล้ว +1

    Where can I get hall sensors

    • @innovationic
      @innovationic  ปีที่แล้ว

      Thanks for comment
      You can take from bldc motor or repairing shop or you can buy online

  • @sefjgroup2271
    @sefjgroup2271 3 ปีที่แล้ว +2

    Good work

  • @JBERGALIEN
    @JBERGALIEN ปีที่แล้ว +1

    good choice for A314 , bad one for the music

  • @ЧёрныйАнгел-б9ь
    @ЧёрныйАнгел-б9ь 2 ปีที่แล้ว

    So sensor output seems negative... in relation to positive common.

    • @innovationic
      @innovationic  2 ปีที่แล้ว +1

      yes its output is negative so you can use PNP transistor to get positive signal

    • @ЧёрныйАнгел-б9ь
      @ЧёрныйАнгел-б9ь 2 ปีที่แล้ว

      @@innovationic No, I don't want to. Just will ask Arduino to look for low signal )

    • @innovationic
      @innovationic  2 ปีที่แล้ว

      just use pullup resistor to your Arduino input or use opamp to get desired output(either +ve or -ve)

  • @kennedy6971
    @kennedy6971 2 ปีที่แล้ว +4

    Why does the watcher have to put up with the music? I refuse to listen.

    • @innovationic
      @innovationic  2 ปีที่แล้ว

      I think people watching videos with music makes them to feel better. Otherwise music or audio depends upon type of video.

    • @Zero-oh6ek
      @Zero-oh6ek ปีที่แล้ว +1

      @@innovationic yep but tbh the music is too loud.

    • @innovationic
      @innovationic  ปีที่แล้ว

      Thanks for your comment
      In upcoming videos I do my best

    • @ryanb3.23
      @ryanb3.23 8 หลายเดือนก่อน

      Then turn down the volume😂😂😂​@@Zero-oh6ek

  • @sabhajeetverma7828
    @sabhajeetverma7828 ปีที่แล้ว

    होल सेंसर अगर मंगवाना चाहे कैसे मंगवा सकते है

    • @innovationic
      @innovationic  ปีที่แล้ว

      Amazon par mil jayega ya apke local electronics store me mil jayega

  • @srfilms3736
    @srfilms3736 ปีที่แล้ว

    Bhache log bejao taali

  • @mohabelkayala9317
    @mohabelkayala9317 3 ปีที่แล้ว +3

    noisy

    • @innovationic
      @innovationic  3 ปีที่แล้ว +1

      Thanks for comment 😊 I make more interesting and better videos in future🙂