Sir ji mere paas 12 watt ka paynal hai us ka sarkit kharab ho chuka hai us paynal ko dubara chalu karna ho to kitne watt ka sarkit lage ga ji yeh batao ji please reply jarur dena ji thanks 🙏 ji
Guruji ek confusion hain pl. clear . 9w or 12w or 18w led ka voltage and current check always load de ke karna hain yea bina load de ke bhi voltage and current check kar sakte hain.
आपके वीडियो मैं पूरे भरोसे के साथ नियमित रूप से देखता ही नहीं बल्कि उस पर अमल भी करता हूं। जैसा कि मैने यह पाया है कि rc driver circuit में AC voltage fluctuation को कंट्रोल करने के लिए कोई भी guidelines आपके द्वारा नहीं बताई गई है। कृपया यह बताने की कृपा करें कि क्या protection use किया जा सकता है ताकि fluctuation के समय circuit को प्रोटेक्ट किया जा सके और bulb में लगी led भी fuse न हो साथ ही साथ customer को भी असुविधा न हो सके। आपके द्वारा बताई गई circuit में कितने miliamps की current सही मानी जा सकती है। 24,36,45 या 50 watts के bulb की कितने miliamps current सही मानी जा सकती है। आपकी महत्त्वपूर्ण जानकारी की प्रतीक्षा में आपका follower
Lot of thanks sir ji . In this context I want one more quarry i.e. you have connected 25 watt rc driver with 48 watt led plate and out put current as shown is 313 or 318 mAmps. Will you pl also clarify that the led used in the mcpcb is which volt and watt. I mean leds are used by 6 volt 1 watt operating voltage or 3 volt 1 watt. May I used 9 volt 9 watt (9 volt x 9 led set)mcpcb with this driver .If so, how many mcpcb can I use for 25,36 or 45 watt respectively with the described watts rc driver as per your genius gudiance. Since, I most really your guidance and I have to arrange 4 rc driver for 36 and 45 watt each. Hope your proper guidance will definitely communicated to me earliest possible. I am anxiously awaiting your sweet reply on the point. Thanks.
Sir, 12 ohoms 2 watts registence nahi mila, dukandar 120 ohoms 2 watts de diya, kya isse kaam hoga kyun ki 4 registence parallel karne se 30 ohoms 8 wdtts ka ho raha hai
My dear friend. Not only people in your own country are watching you, but people from all over the world are watching you. Therefore, could you please write the values of the electronic parts you used on the screen in the video, thank you.
Sirji. I made the circuit as per your diagram for 50w. All the component were used as per your instructions. After completion, I checked the voltage without connecting to 50w streetlight. It shows DC 350v output.Orginal driver output is 45v. 1500 ma. I am scared to connect my 50w streetlight. As smd are expensive now days. What should I do. Pls advice.
Driver output voltage shows 350VDC when MCPCB is not connected (no load). First the driver is connected to the MCPCB, then to the supply driver. But not recommended for street lights...
Apka Bahot bahot Shukriya .
Jo App Hamre Liye Mehnat karte hai 👍
Waah very good job
Bahout Asha bataya Aap ne
🌹🌹🌹🌹🌹🌹🌹🌹🌹🌹👌👌👌👌👌👌👌👌👌👌👌
बहुत ही बढ़िया ड्राइवर बनाया है सर जी
Than you very much sir aapni mere recommendation per 50v ka pf circuit banana sekaya Than you so much
बहुत अच्छा समजमे आये मुझे बहुत अच्छा लगा है
Sir aapke samjhane ka tarika bahut achha laga thank you
Thanks for appreciation and feedback...
Very knowledge full video si
Jhakkas Suuppeerrbb Performance 👌
Very good presentation good explain thanks
Very Nice Information Mishra Ji
Thanks for feedback.... Gopal Ji..
Very nice information 👍
बहुत अच्छा आईडिया धन्यवाद गुरुदेव
nice innovation SIRJI
👍👍👍👍🙏🙏🙏🙏🙏
Very good knowledge sir
50 watt led flood light keliye chalega?
Nice information sir Ji
Nice representation. I will try it. Tripura.
100% working... Try it and share your valuable feedback...
Very nice vdo thanks a lot sir g
Nyc information ℹ️ℹ️
30w led bulb k liye kya kare?please reply me.thanks
Sir thank you ❣️😍🙏🙏🙏🙏
Praji tussi great ho...
Thanks praji, but aap wastav mein ek alag hi Video lekar aate ho. Great.
Alternative to pf would be great as it's taking up more space.
Very informative video thanks.
Sir pls make video on 9w and 12w driver
50watts circuit can be used for 50watts street light. Pls let me know
Achi jankari mil sir.....
Stay tuned with #ZeroLab
Suppppebb VEDEO 🌹🙏🙏
Thanks for feedback...
Diode in 4007use kre skte hai kya🤔
Very good information and explanation sirji. 30W ke liye kya change karna padega.
Check video description...
25W 2nos335pf parallel and 35W 3nos 335pf parallel lagana. 30W ke liye?
Very nice video
Excellent repair videos.
Sir 335J available na ho to dusra kaun sa use kare
Serji Electric fence gurd ma circite diogram bana de sakte hai🙏
Good information thanks
ktni 8mm ki led jod sakte he sirji
sir moter starting wala 12uf capacitor use kar skte h kya 50w mcpcb k liye itne capacitor perler m lagane ki kya jarurat h
Tnx dada❤❤❤
very good video thanks bhai. 7.5.2022
Sir,100 yaa 120 watt Street light k liye mene 10PF laga sakta hu.
Rc driver n normal chip driver mein kiya farq hota hai or RC driver voltage fluctuations ko control kr sakta hai
Sir home made led bulb mai diffuser led light se kitna dur hona chahiye
Sir ji mere paas 12 watt ka paynal hai us ka sarkit kharab ho chuka hai us paynal ko dubara chalu karna ho to kitne watt ka sarkit lage ga ji yeh batao ji please reply jarur dena ji thanks 🙏 ji
Led tub like. Mai. Kam karega. Kay
very nice vedio sir
Thanks for appreciation and feedback..
Proof your statement by glowing the 48W PCB and check the watt consuming
Thanks for your support and good wishes
Always welcome...
Sir, namaskaar jis mcpcb mein capacitor aur Kai sare components lge hote hai uss mein lgne wala driver banaye please
Sir a rc driver ac may canaction kiya orsirise bulb sate /galu dikharahahi
Sir 18 w philipsled bulb me 2segment wala mc pcb jal nahi raha hai please guide
Ap kisamghane ki bahut good hai25w me 2pf 35w me3pf50w me4pf
Is ckt ka DC output voltage kya hai...?
Nice video
why four 12 ohm resisters instead of one 3 ohm resistor?
40 watt ke street light chal sakte hai esa
Yes...
Agar 335j 450v nahi milayga
Ess k badlay kon sa valve ka lagana please
Hi sir
4.7ohm ka resistance heat hoke black hota hai
Isliye kya kare uske badle konsa laga sakta hu
Is circuit se 50 watts ki mcpcb sahi jalegi aur iski life kaisi hai
Sir ciling fan ke capacitor ko discharge karne ke liye konsha resistance lagana padega 4mf ka capacitor he
Please sir javab dijiye ga
Use kime krna hai....
@@TechToolsElectronics Street light me voltej kam karne ke liye lagaya hai sir supply ki taraf sirij me 4mfd ka sir
Sir a prts kaisa milaga
Hi sir good morning
35 w ki light main lagaya to brightness nahi hai bahut kam glow kar rahi hai
Isaliye kya kare
Kya is tarike se 24v 3amps output ka driver bana sakte hai?
protection vali mob battery charge konse module se hogi ?
Can I use kbpc3510 bridge
220 volt Dena hai ji
Sir flood light 50watt ke liye circuit banaye jo light ko accha glow kara sake
Good work
esse circuito dura muito tempo ja fiz em umas lampadas nunca deram problemas
Thanks for this video,sir kya hum ye pf driver se 50w ke flood light chala sakte hain ? Waiting for your reply.
चलेगा कितने दिन...????
Sir Ji kya ham 50w LED ke liye bridge rectifier in 4007 Laga sakte hain?
Minimum 2 Amp Diode use kro
For 50w output instead 4 nos 450v can we use one 2000v such capacitor? Lot of space can be saved! Please reply. Thanks
No...
Explore your knowledge before doing such kind of experiments
hi friend...(Output Current Control Resistance 12 Ohms 2 Watt ..?)................ is (4x12 Ohms or 4x47 Ohms) ?... thank U.
Guruji ek confusion hain pl. clear . 9w or 12w or 18w led ka voltage and current check always load de ke karna hain yea bina load de ke bhi voltage and current check kar sakte hain.
Output voltage aur current.... load pr hi test hoga...
@@TechToolsElectronics So thankful to you, Guruji.
Bhai candle led bulb 5watt ke liye bataaye
Sir in driver ki life kitne yeare ki hogi
Shukriya...
Very well sir.
Good work,pls share circuit diagram
27w ki street light chalegi kya sir
Check video description and make 27 watt led driver
आपके वीडियो मैं पूरे भरोसे के साथ नियमित रूप से देखता ही नहीं बल्कि उस पर अमल भी करता हूं। जैसा कि मैने यह पाया है कि rc driver circuit में AC voltage fluctuation को कंट्रोल करने के लिए कोई भी guidelines आपके द्वारा नहीं बताई गई है। कृपया यह बताने की कृपा करें कि क्या protection use किया जा सकता है ताकि fluctuation के समय circuit को प्रोटेक्ट किया जा सके और bulb में लगी led भी fuse न हो साथ ही साथ customer को भी असुविधा न हो सके।
आपके द्वारा बताई गई circuit में कितने miliamps की current सही मानी जा सकती है। 24,36,45 या 50 watts के bulb की कितने miliamps current सही मानी जा सकती है।
आपकी महत्त्वपूर्ण जानकारी की प्रतीक्षा में आपका follower
लिंक में दीया गया वीडियो आपके लिए उपयोगी होगा...
th-cam.com/video/Dzl15VrlGlc/w-d-xo.html
Lot of thanks sir ji . In this context I want one more quarry i.e. you have connected 25 watt rc driver with 48 watt led plate and out put current as shown is 313 or 318 mAmps. Will you pl also clarify that the led used in the mcpcb is which volt and watt. I mean leds are used by 6 volt 1 watt operating voltage or 3 volt 1 watt. May I used 9 volt 9 watt (9 volt x 9 led set)mcpcb with this driver .If so, how many mcpcb can I use for 25,36 or 45 watt respectively with the described watts rc driver as per your genius gudiance.
Since, I most really your guidance and I have to arrange 4 rc driver for 36 and 45 watt each.
Hope your proper guidance will definitely communicated to me earliest possible.
I am anxiously awaiting your sweet reply on the point. Thanks.
What is the output voltage of this driver
Floodlight ka driver video banana plz
Creative video, thanks :)
36 mai kinta pf lagau??
hpf driver ka ic (9w) kaha milaga , ic ka number kaya hai.
Sir, 12 ohoms 2 watts registence nahi mila, dukandar 120 ohoms 2 watts de diya, kya isse kaam hoga
kyun ki 4 registence parallel karne se 30 ohoms 8 wdtts ka ho raha hai
Four 12 ohm resistors in parallel are equal to 3 ohm only.
Vai 200 watt drive banaakr daliye na
kya ye long time ke liye tikaoo hoga
Yes absolutely
Tp4056 module me 8205A ic ki jagh n channel mosfet lga kar output current bada kr dikhaiye jo 3A hota he use bda kar btaiye
Charging current 1Amp hi output hoga... But battery output current increase kr sakte ho...
Hello sir
सर इस सर्किट से 12 बोल्ट 15 amper बनाकर दिखाएं
sir ji gd morning l need a led tester for testsmd led and 50watt RC driver for glow 50watt led bulb
Sir can you please share the components needed to built a 100 watt led driver
Good morning Sir, what is the working of MOV in the electronic?? and please tell it's abrivation also
Watch video link below...
th-cam.com/video/8Mh3aLu8pVo/w-d-xo.html
My dear friend. Not only people in your own country are watching you, but people from all over the world are watching you. Therefore, could you please write the values of the electronic parts you used on the screen in the video, thank you.
Check video description for more details...
Can I use a 40w LED bulb?
Good yar
23 watt circuit ka out put voltage Kitna hoga
SHOW live test pls
👌👌👌👍
Nice sir
Sirji. I made the circuit as per your diagram for 50w. All the component were used as per your instructions.
After completion, I checked the voltage without connecting to 50w streetlight. It shows DC 350v output.Orginal driver output is 45v. 1500 ma.
I am scared to connect my 50w streetlight. As smd are expensive now days. What should I do. Pls advice.
Driver output voltage shows 350VDC when MCPCB is not connected (no load). First the driver is connected to the MCPCB, then to the supply driver. But not recommended for street lights...