Always funny to see that many people criticize someones work he would like to show. You think you're better than him? Upload your video. I haven't seen them yet. This video is pretty good and he delivers nice work. Thanks for sharing.
Brilliant install video! Finally one that has real life problems and how to overcome them. Every other install video just makes it look easy and it’ll be up in 2mins. Great explanations, top points to you sir!
Great tutorial! Looking to try this myself. I like how you showed all the tools and measuring and gave your advice on certain things to look out for. Very informative. Thank you!
Great tutorial. For the electric socket, I would personally use some ply to shim between the wall and a patress box to bring the socket forward flush with the panel.
@@sackville_bagginsessYou wouldn’t get gaps but I suppose you would see the white plastic in between the slats but you could of course paint that, at least it would be safe and accessible though.
If you have to have cuts, cut the panels and make sure the cuts are at low level, having the cuts high level is closer to eye vision, lower the better and also use a skeleton back in box for the sockets
That looks a right mess at the top! For starters I’d have done that at the bottom, because you’re more likely to have it concealed by furniture. But, really all you needed to do was buy the slightly longer ones and cut them down to size for a full length no seam finish! Any off cuts you can use for other little projects.
Socket cut outs should be smaller than the face plate so the face plate can be fitted in front to hide the opening. Buy slats that are floor to ceiling length or put the cut somewhere less obvious e.g. behind your bed frame. An alternative look is just to fix slats to the bottom half of the wall.
I was thinking of battening the wall because I wanted to go for the effect of the slat wall not reaching the floor or ceiling. I won't have to remove the skirting board and it allows backlighting.... The sockets could be a little tricky though, deep back box should do it 🤞
Good idea. But i found that when u tighten the socket against the wall panel, the slats kick in due to the spongy back, too loose and the socket moves about when plugging into it. Catch 22 im afraid
I agree with the cutting around the sockets this would look better, however I'm not allowed to tell viewers to remove a socket face to then remount her the cut if they aren't qualified electricians!
great vid acutally got some free samples from the site which is great but i've gotta go around a window and im not looking forward to it but seeing this give me a little more confidence
It shouldn't be a problem going round windows reveals, do check out our other videos of installing these boards around our bed headboard as its similar technique.
The top half cut-in is what I was most interested in, but all the photo shots blurred it out. When one buys panels that don't make it to the top, how good can someone hide the lines? I think, cannot.
would it be an idea to run the long panel from the ceiling down having the joint at the bottom, usually bed/lockers will obscure them more, but maybe a bit my fiddly to fit.
Nobody mentions that the skirting wasn't checked for level, as the bottom of the board is sitting on this it may be the skirting that is causing the first panel to be out of plumb.
If you are doing a cut that leave the slats moving around, it’s better to staple the felt to the batten on the back, near to where you are going to cut. Much better than gluing them
Gluing is far more accurate as he got them dead in line with the others and remember that he had made cuts so they weren’t completely accurate, most walls are like this so it makes 💯 sense
I dunno abiut that top row. I would have either not bothered and just painted behind it or I would have added extra staples before cutting them because that method stands out as it's certainly not in line with the rest of the slats
firstly, use glue to stick them up, whether thats contact glue or a construction adhesive. secondly, use a galvanised extension box to bring the socket out, cut the hole for the socket the same size as the back box so the socket face overlaps the wood, get a roll of black felt tape, wrap the metal extension box in felt tape so that when you look down on it you cant see the metal extension box. done this lots of times and looks fantastic
@@adamwainwright3192 yes, probably but if your removing the entire wall covering that’s hardly a small decision. Construction adhesive is how many of the manufacturers instructions tell you to install it.
It depends how strong of glue you use and how well bonded your plaster is to the surface below, Most cases it should be a problem, but best check with your supplier and do you own investigation on the condition of your plasterwork @@adamwainwright3192
Im about to do this but have a question, i need to run 2.5 cable for additional sockets will the cable fit behind the panels or am i better to recess a hole in the plaster...thanks
Hi, yes you can use adhesive instead or as well as screws! We'd recommend this one: www.wallsandfloors.co.uk/nail-free-panel-adhesive?_br_psugg_q=panel%20adhesive
Just be careful with the mains sockets if the facia's are fitted flush on top of the wood slat and the back box ( plastered in place ? ) is left in the solid wall a small gap would be open between the slats that a child could get there finger behind the socket facia and possible touch the live contact. Would be best to fit off cuts of wood or felt to cover gaps or clip in plastic box with back removed. I no it is pickee but just a through.
you would be best just cutting a big hole big enough to mount the bracket in, like a large version of what he did on the sockets. the tv will hide the hole anyway.
Yes, you would screw through the felt to install your wood panel to the wall. We would recommend using screws similar to the colour of the felt to make them near invisible.
are drywall screws really necessary for this? the slats are at extremely low inertia force torwards the floor when they are sitting on top of the trim like that, seems like you could just nail it in and be fine.
Hi, they have some sound-absorbing qualities due to the felt backing. Our fitting guide has some alternative fitting methods to improve the sound levels even further: chrome-extension://efaidnbmnnnibpcajpcglclefindmkaj/m2.wallsandfloors.co.uk/media/amasty/amfile/attach/DesignDataSheet_Updated_3_.pdf/. Thanks, Emily
You should buy 2.9m in height to get the full height in one length rather than buying 2.4m and then adding stupid pieces and have a line there which’s not a professional job at all
It's a pity that you have to struggle with these panels not produced with enough height, so a beautifully wall is kind of ruined by that little piece at the top; looks amateur. I would have bought one, if manufactures had offered 9 feet height.
Why are they not possible to be stuck to wall like most wall panels? 75 holes drilled & plugged!! excessive work, when in many cases drywall is blob & dabbed to walls!
One question for all you ‘master craftsmen’ why are you watching tutorials if you’re all armchair craftsmen?? #funnyasfook #pleaseshowusyourway #theonlywayissatonyoursofaonyourphone #lazy #negativevibessuck
Shocking aren't they was just thinking the same . Feel sorry for Craig but half of these people on here sound like they need to be on anti depressants.😅
Hey guys! Craig also dropped 2 videos on our channel! 👉How to Install Wood Slat Wall Panels to Stud Walls 👉How To Install A Wood Slat Headboard 🏃♂Go Check them out!
Sockets look awful and the extra slip on top as apposed to having a length longer than the floor to ceiling and cutting that so its one piece is also not very appealing!
Would you please let us all know when you post your tutorial of how to do it as you’re clearly a professional?! I mean, why else would you look up tutorials? 😴 #armchairbuilder #daydreamer #trollsareus
I really like this look but I am now seeing it everywhere online and it now feels like a fad. It feels like in 2030 everyone will be able to come into your home and think - thats so 20’s - really dated. And it’s not like it’s truly a snap to put up and won’t take a lot of drywall repair if you decide to rip it out and update. So for me while I love it - I’m not wasting my time and money on it.
Always funny to see that many people criticize someones work he would like to show. You think you're better than him? Upload your video. I haven't seen them yet. This video is pretty good and he delivers nice work. Thanks for sharing.
Many thanks my friend
Yes, fully agree. People making negative comments should a video of their own.
Superb content ! Clear, not verbose, unambiguous! Bloody perfect.
*Best wishes*
Glad you liked it!
Brilliant install video!
Finally one that has real life problems and how to overcome them. Every other install video just makes it look easy and it’ll be up in 2mins.
Great explanations, top points to you sir!
Thank you very much, glad we could help you
Just got half way through this excellent video and felt like I know this guy, then it dawned on me Big Brother. Great installation and tips.
Great tutorial! Looking to try this myself. I like how you showed all the tools and measuring and gave your advice on certain things to look out for. Very informative. Thank you!
Glad it was helpful!
Great tutorial. For the electric socket, I would personally use some ply to shim between the wall and a patress box to bring the socket forward flush with the panel.
Great idea
Wouldn't it leave gaps between each slat?
@@sackville_bagginsessYou wouldn’t get gaps but I suppose you would see the white plastic in between the slats but you could of course paint that, at least it would be safe and accessible though.
I stumbled on this video through suggestions and I'm left feeling glad that Craig got out of Avid Merrion's cupboard.
Cheers
🤣🤣🤣🤣 right?
Hahaha @@andrewmccoy8446
and he got out of the Big Brother house as the first winner!
Thanks right, @@Bend_Sinister
If you have to have cuts, cut the panels and make sure the cuts are at low level, having the cuts high level is closer to eye vision, lower the better and also use a skeleton back in box for the sockets
This man is a real tutor by nature, Awesome work 🥂🔥
Thank you! Much appreciated!
Love his videos the way he explains everything gives you the confidence to do it yourself ❤
You can do it! 🙌🏼🙌🏼
Thanks, glad its helping
Best installation video by far
Cheers
That looks a right mess at the top! For starters I’d have done that at the bottom, because you’re more likely to have it concealed by furniture.
But, really all you needed to do was buy the slightly longer ones and cut them down to size for a full length no seam finish!
Any off cuts you can use for other little projects.
I don't disagree.
Best tutorial on installing slat walls out there by far. Saved me from many mistakes. Subbed
Many thanks
I used your technique, but glued mine on.
Most clear tutorial. Really helpful
Many thanks
Thanks Craig
Socket cut outs should be smaller than the face plate so the face plate can be fitted in front to hide the opening. Buy slats that are floor to ceiling length or put the cut somewhere less obvious e.g. behind your bed frame. An alternative look is just to fix slats to the bottom half of the wall.
I was thinking of battening the wall because I wanted to go for the effect of the slat wall not reaching the floor or ceiling. I won't have to remove the skirting board and it allows backlighting.... The sockets could be a little tricky though, deep back box should do it 🤞
@@keendnbdeep back boxes and paint the exposed metal or plastic black. Should be a nice finish.
Good idea. But i found that when u tighten the socket against the wall panel, the slats kick in due to the spongy back, too loose and the socket moves about when plugging into it. Catch 22 im afraid
I agree with the cutting around the sockets this would look better, however I'm not allowed to tell viewers to remove a socket face to then remount her the cut if they aren't qualified electricians!
@@keleelaslam3007 Before you fit the panels fix batten around your sockets so when you install the panel it won’t pull in!
great vid acutally got some free samples from the site which is great but i've gotta go around a window and im not looking forward to it but seeing this give me a little more confidence
let us know if you need any advice!
It shouldn't be a problem going round windows reveals, do check out our other videos of installing these boards around our bed headboard as its similar technique.
The top half cut-in is what I was most interested in, but all the photo shots blurred it out. When one buys panels that don't make it to the top, how good can someone hide the lines? I think, cannot.
Great illustration Craig. Legend
would it be an idea to run the long panel from the ceiling down having the joint at the bottom, usually bed/lockers will obscure them more, but maybe a bit my fiddly to fit.
Yes it would certainly work that way, our wall panels have been up for 3 months now and no body has noticed the joint
How can u plug anything in cable comes out the bottom of plug better cutting bit smaller and sitting the socket flush with slats
I learned something today.Thanks mate 👍
“put your board upon the wall” spoken like a true poet😂
I think I would paint the black edges on each side white, that would hide how out of plumb those corners are.
That's a great idea. Thanks
Nice job
Thank you!
Nobody mentions that the skirting wasn't checked for level, as the bottom of the board is sitting on this it may be the skirting that is causing the first panel to be out of plumb.
These look pretty good but not sure if the wider slat version would look better than the one youve installed
If you are doing a cut that leave the slats moving around, it’s better to staple the felt to the batten on the back, near to where you are going to cut. Much better than gluing them
Gluing is far more accurate as he got them dead in line with the others and remember that he had made cuts so they weren’t completely accurate, most walls are like this so it makes 💯 sense
@@SPS_survivor if you staple them, they will be dead in line anyway, and you get a better cut as the small slats aren’t moving when you are cutting
Good idea thanks
Thanks @@SPS_survivor
Always wondered what happened to Craig after Big Brother...clear talker for a Scouser 😊
It's actually him isn't it ?
Yes it certainly is @@adamcunningham2511
Working hard @markpresbury2110
Ah ha. That's where I recognise him from. It was doing my head in. I knew the comments section would save me. Cheers❤
Cheers
Thank you for the video, subbed!
Thanks! Let us know if you have any questions
Many thanks
Thanks for the tutorial! Very helpful…
You're welcome 🥰glad you found it useful!
I dunno abiut that top row. I would have either not bothered and just painted behind it or I would have added extra staples before cutting them because that method stands out as it's certainly not in line with the rest of the slats
wouldve been better to do them at the bottom and not the top
firstly, use glue to stick them up, whether thats contact glue or a construction adhesive.
secondly, use a galvanised extension box to bring the socket out, cut the hole for the socket the same size as the back box so the socket face overlaps the wood, get a roll of black felt tape, wrap the metal extension box in felt tape so that when you look down on it you cant see the metal extension box. done this lots of times and looks fantastic
All sounds good thanks
If you used glue/adhesive would it not rip of the plaster if you ever decide to remove these slats?
@@adamwainwright3192 yes, probably but if your removing the entire wall covering that’s hardly a small decision. Construction adhesive is how many of the manufacturers instructions tell you to install it.
It depends how strong of glue you use and how well bonded your plaster is to the surface below, Most cases it should be a problem, but best check with your supplier and do you own investigation on the condition of your plasterwork
@@adamwainwright3192
Im about to do this but have a question, i need to run 2.5 cable for additional sockets will the cable fit behind the panels or am i better to recess a hole in the plaster...thanks
Hi, you would probably best to recess a hole in the plaster as the panels will need to sit flush to the wall. Thanks, Emily
Good idea starting from center. I will do that. Can i not just use adhesive instead of screwing them on?
Hi, yes you can use adhesive instead or as well as screws! We'd recommend this one: www.wallsandfloors.co.uk/nail-free-panel-adhesive?_br_psugg_q=panel%20adhesive
@@wallsandfloors perfect thanks i ordered these panels from your website too
Looks good.
Cheers
Thank you
Hlo, can you suggest me from where I can buy grey wood panel and who can fix in TX
Hey! Herer are our grey panels: www.wallsandfloors.co.uk/wood-wall-panels/by-colour/grey-wood-wall-panels
Take sockets off purchase longer screws still looks great though 👊
Thanks
Can’t you get them in longer lengths so you avoid that thin strip at the top?
Why not long electric socket screws and leave the sockets flush. I think you would have trouble getting a lot of plugs to fit into the socket.
What were the measurements for those pannels?
Hi, these are 2400mmx600mm and we also do 1200x600 and 600x600. Thanks, Emily
Are screws needed? Have seen some use just the glue. This screws just go straight in the wall without any wall plugs?
hi, you can use either screws or adhesive to attach them. It will depend on the type of wall whether you need plugs or not. Thanks, Emily
Is it worth messing up the wall?
can you use liquid nails instead?
Just be careful with the mains sockets if the facia's are fitted flush on top of the wood slat and the back box ( plastered in place ? ) is left in the solid wall a small gap would be open between the slats that a child could get there finger behind the socket facia and possible touch the live contact. Would be best to fit off cuts of wood or felt to cover gaps or clip in plastic box with back removed. I no it is pickee but just a through.
Its a very thing to point out, thanks
do you have a video of installing a tv on this type of wall
Hi, we don't but you can do this. You just need to screw through the felt into the wall behind. Let us know if you need any help. Thanks, Emily
you would be best just cutting a big hole big enough to mount the bracket in, like a large version of what he did on the sockets. the tv will hide the hole anyway.
Wouldn't it be easier to paint the wall black and just install wood slats?
Would it be okay to install them horizontally if the walls are not level? That way you won't notice it?
Hi, yes you can install them horizontally.
Wait you just screw the felt in???
Yes, you would screw through the felt to install your wood panel to the wall. We would recommend using screws similar to the colour of the felt to make them near invisible.
Can you put foil insulation behind them to help keep the heat in?
I'd double check with Walls & Floors
@@MrandMrsDIY Thank you. A great video by the way.
The foil can be used behind the Trepanel, yes. You would, however, have to use screws to fix the panel, not adhesive.
@@wallsandfloors Brilliant thank you 😊
are drywall screws really necessary for this? the slats are at extremely low inertia force torwards the floor when they are sitting on top of the trim like that, seems like you could just nail it in and be fine.
the manufacturers recommend it for max strength
Liquid nail and use a few nails to hold untill it dries screws are definitely not necessary these are very light weight
Lovely 😍 sir
Excellent work! Thank you
How much did it cost to do that wall?
The panels' RRP is £99.95 / panel. They currently have up to 25% off and we have smaller panels that start at £24.95. Thanks, Emily
@@wallsandfloors Thanks
Do you have a link?
Here you go - www.wallsandfloors.co.uk/wood-wall-panels
professional
How do you hide the screws?
you can use black screws to blend in with the backing foam!
Is there anyway to remove the individual wooden slates?
I suggest you rewatch the video
The wall never be level but it may or not be upright
Plumb . The wall is not plumb.
Is that the guy that was on big brother years ago?
Yes!
What colours are these slat panels?. They look greyish bluish and not green.
This is the juniper shade which is a sage green tone. Here's the link: www.wallsandfloors.co.uk/trepanelar-juniper-acoustic-wood-panels. Thanks, Emily
How much for each panels
Our panels are normally £99.95 / panel however right now they are 25% off so they are only £74.96 / panel. Offer ends Wednesday midnight. 😎
@@wallsandfloors Link?
Great video!!!! I plan on doing an entire room in this way & install LED lighting within the slots… give it a running effect…
That will look great!
Friesen Locks
wall panel manufacturer from china, any chance to cooperate?
Glued mine with gorilla glue spot on
Adhesive is a great alternative to screws!
how effective are these panels when it comes to acoustic isolation?
They are going to certainly benefit the acoustic value and help with the insulation if fitted well.
Hi, they have some sound-absorbing qualities due to the felt backing. Our fitting guide has some alternative fitting methods to improve the sound levels even further: chrome-extension://efaidnbmnnnibpcajpcglclefindmkaj/m2.wallsandfloors.co.uk/media/amasty/amfile/attach/DesignDataSheet_Updated_3_.pdf/. Thanks, Emily
You were getting confused between level and plumb! 😂
Hahaha
Is this the geezer who won big brother 40yrs ago?
It is indeed
I was going to get these for my room but to be honest with you it's a bit too much faffing about. And when it's done it won't look perfect😩
There's certainly not faffing around, they go in quick and easy, and will look great for many years to come
@@MrandMrsDIY it doesn't look like they go up easy
We have a TH-cam short dropping today at 16:20 showing 3 panels being completed in only 3 minutes! Stay tuned! @@davidmckee2898
Check out our other installation videos when I glue the boards to a stud frame its so much quicker and easier @@davidmckee2898
Never going to be able to use those sockets
I'm no expert, however it seems to me that if you had started in one corner you would only have to cut ONE board....
Ok, I have never done this job before, so I watched his video. I usually do it the way I like in the end, but I would love to see your video.
FIFTEEN screws per panel! Do they really need that many? I can't see why. Does it depend what type of fixings you're using?
Hi, we recommend 15 due to the size of the panel as they are 2.4 metres in height. Or a tube of adhesive. Thanks, Emily
@@wallsandfloors thanks, I got them fitted and used the 15 screws. They look superb!
@@crackspider101 Great to hear that
Great tutorial, but I woulr not call this quick or easy😂
Brown Sarah Moore Elizabeth Hernandez Mark
Gonzalez Jason Anderson Edward Rodriguez Ruth
Perez David Williams Brian Anderson Robert
Davis Matthew Rodriguez Angela Jones Jessica
You should buy 2.9m in height to get the full height in one length rather than buying 2.4m and then adding stupid pieces and have a line there which’s not a professional job at all
I guess I’m just lazy but the finished results just aren’t worth the amount of work that goes into installing this material. I’d rather do shiplap.
Taylor Scott Hall Charles Miller Larry
Young Laura Harris Larry Jackson Michael
It's a pity that you have to struggle with these panels not produced with enough height, so a beautifully wall is kind of ruined by that little piece at the top; looks amateur. I would have bought one, if manufactures had offered 9 feet height.
Yes it would certainly work that way, our wall panels have been up for 3 months now and no body has noticed the joint
Johnson Michael Lewis Sarah Martin Jessica
Jones Karen Brown Carol Jones Melissa
Look how many tools he needs just to install these slats 😂
Why are they not possible to be stuck to wall like most wall panels? 75 holes drilled & plugged!! excessive work, when in many cases drywall is blob & dabbed to walls!
Hi Alan, they can be stuck to the wall with a board adhesive. This is just an alternative method. Let us know if you have any questions! Thanks, Emily
It's plumb, not level you are looking for, Mr DIY.!!
Noted!
White Ronald Martin Christopher Clark Frank
These wall panels contain too much glues...It is made of wood scrap..
Gap on the left where cut was made is awful
One question for all you ‘master craftsmen’ why are you watching tutorials if you’re all armchair craftsmen?? #funnyasfook #pleaseshowusyourway #theonlywayissatonyoursofaonyourphone #lazy #negativevibessuck
Shocking aren't they was just thinking the same . Feel sorry for Craig but half of these people on here sound like they need to be on anti depressants.😅
ignore the lot
Not level …. plumb !
Hard on the eyes
Hey guys! Craig also dropped 2 videos on our channel!
👉How to Install Wood Slat Wall Panels to Stud Walls
👉How To Install A Wood Slat Headboard
🏃♂Go Check them out!
Thanks guys
Sockets look awful and the extra slip on top as apposed to having a length longer than the floor to ceiling and cutting that so its one piece is also not very appealing!
Would you please let us all know when you post your tutorial of how to do it as you’re clearly a professional?! I mean, why else would you look up tutorials? 😴
#armchairbuilder #daydreamer #trollsareus
There is always something to learn from watching tutorials. Belittling someone else’s preference of how they do things is unappealing.
Looking forward to DaveFox’s video on how to do it better.
@@grishyroy9271you’re wife has watched my video on how to do better many times so she should be able to walk you through it 👌
No one asked
I really like this look but I am now seeing it everywhere online and it now feels like a fad. It feels like in 2030 everyone will be able to come into your home and think - thats so 20’s - really dated. And it’s not like it’s truly a snap to put up and won’t take a lot of drywall repair if you decide to rip it out and update. So for me while I love it - I’m not wasting my time and money on it.
That is some annoying accent
Cuts at the top look horrendous!!!
Show us a video of your craftsmanship then Mr keyboard warrior
What a silly fad these walls are, socket finish looks bad
Wouldn't listen to him if you paid me!!