Thankyou sa video na to buti nakita ko. May isa lng ako hndi pa mabalik kung saan dpat nkalagay yung parang number 9 Yung isa nalagay ko na sa isang turniyo,saan kana yung isa? Thankyou
I hope hnd pa huli na matulungan kita sa problema mo. Super poor ang connection sa location ko that's why hnd ako maka online ng matino. Panoorin mo ang Link, makita mo dun saan mo nakalikot si hugis nwebe (9).🤭👍😅 thank you and tc.
Hello Elizebert. I am not a technician but I hope that my opinion helps you. If your roller won't work, then my guess is your machine's motor need replacement. You need a technician to diagnose your machine.
Unfortunately I haven't experience your concern. However if ever it happens to me then I will carefully remove the film with hard tools like flat screw. And then clean the metal carefully with WD-40.
Oh man. Idk if you are able to help me. But i took my machine apart because it had a bad jam in it. And now i can't remember where 2 of the metal pieces go. 😢
Hhhhmmmm... you need the assistance of an expert technician near you. They might have the missing metal you need to fix your machine. But if it cost you too much, it is better to buy a new one.
Gracias por compartir este vídeo. Lo único que no me quedó claro es que si no era necesario limpiar los rodillos ya que la máquina ya estaba abierta 😮, y si fuera necesario con que líquido o como se tendrían que limpiar! (Me imagino que habrá casos en que se pegan residuos del plástico) Cuando trato de reparar algo nuevo voy tomando fotos o vídeo y organizando las piezas en un papel al lado y escribo notas, así cuando tengo que armarlo no me faltan ni sobran piezas 😂😅😊
Ano po ibig nyo sabihin? There's sa laminator brand named "Boye Laminator Machine". Ang hinahanap nyo po is yung board nya mismo sa loob? If yes, I think for order lang yan sa binilhan nyo. Otherwise, ipa repair nyo if may sira. But best advice is bili po ng bago.😅 Thanks for asking and apology for the late reply.
1st, baka hindi mo po naibalik ng maayos after mong mabuksan ang machine mo. Or 2nd, ang honest review ni TEEDA laminating machine ay may downside, sa unang roll nya meron yung hnd sya mag dikit ng maayos kaya need mo ulit ulit. At baliktarin mo pagka ulit mo. At wag lagi sa gitna ipadaan.
Madami po pwdng dahilan nyan. Katulad ng: Hnd gumagana ang outlet. Kulang ang daloy ng kuryente. Sumabog ang saksakan. Kinagat ng pusa o daga ang wire.😅 At higit sa lahat baka may problema ang Iron Plate nya or Heating coil. Kung okay po ang outlet at saksakan ng laminator nyo. Subukan nyo po ipa On ng 5 to 10 minutes. If wala parin kayong ma feel na init. Kailangan nyo na po ng technician lalo na if wala po tayong idea sa pag repair.
Fist is check the power outlet kung gumagana ba talaga. If yes, at hnd parin init, ipa check mo sa electrician baka nag short-circuit. Kung gumana sya after mo mabili means hnd sya factory damage. Try mo din mag wait 5 to 10 minutes after mo ma on dun sa "hot". If hnd tagala uminit dalhin mo sa electrician.
Marami ka Ng viewers 🎉❤
Thankyou sa video na to buti nakita ko.
May isa lng ako hndi pa mabalik kung saan dpat nkalagay yung parang number 9
Yung isa nalagay ko na sa isang turniyo,saan kana yung isa? Thankyou
m.th-cam.com/video/hb9KISqX2_g/w-d-xo.html
I hope hnd pa huli na matulungan kita sa problema mo. Super poor ang connection sa location ko that's why hnd ako maka online ng matino. Panoorin mo ang Link, makita mo dun saan mo nakalikot si hugis nwebe (9).🤭👍😅 thank you and tc.
Vary gud ❣️
Why my machine roller can not function? Hope u can help
Hello Elizebert. I am not a technician but I hope that my opinion helps you. If your roller won't work, then my guess is your machine's motor need replacement.
You need a technician to diagnose your machine.
How bout if the film was rolled and stuck completely and i cannot pull it because it was dried up and sticked at the metal part?
Unfortunately I haven't experience your concern. However if ever it happens to me then I will carefully remove the film with hard tools like flat screw. And then clean the metal carefully with WD-40.
If you're worried to DYI your machine. Always ask the help of technicians near you.
Oh man. Idk if you are able to help me. But i took my machine apart because it had a bad jam in it. And now i can't remember where 2 of the metal pieces go. 😢
Hhhhmmmm... you need the assistance of an expert technician near you. They might have the missing metal you need to fix your machine. But if it cost you too much, it is better to buy a new one.
@aihnsvlogEDL I figured put how to put my machine back together 😃 thanks
@@KatMz7 Hii I also can’t remember where 2 of those metal pieces go.. 🥴How did you put them in?
Gracias por compartir este vídeo. Lo único que no me quedó claro es que si no era necesario limpiar los rodillos ya que la máquina ya estaba abierta 😮, y si fuera necesario con que líquido o como se tendrían que limpiar! (Me imagino que habrá casos en que se pegan residuos del plástico)
Cuando trato de reparar algo nuevo voy tomando fotos o vídeo y organizando las piezas en un papel al lado y escribo notas, así cuando tengo que armarlo no me faltan ni sobran piezas 😂😅😊
May nabibili bang buing board ng heavy duty na laminator like quaff laminator
Ano po ibig nyo sabihin?
There's sa laminator brand named "Boye Laminator Machine".
Ang hinahanap nyo po is yung board nya mismo sa loob? If yes, I think for order lang yan sa binilhan nyo. Otherwise, ipa repair nyo if may sira.
But best advice is bili po ng bago.😅
Thanks for asking and apology for the late reply.
New subscriber here. 🙋♂️
Thanks for the support Mardz.
I have a problem in my machine thermostat cant work and can't turn off automatically. Please help as fast as you can
In this case, you need to bring your machine to an electrician near your place.
Ye masin ke gear mill jayega kiya
Yung laminator ko po parang hindi nya napipress ng maayos yung film pagkatapos ko po sya kalasin noong nagjammed sya ... Ano po kaya dapat kong gawin?
1st, baka hindi mo po naibalik ng maayos after mong mabuksan ang machine mo. Or
2nd, ang honest review ni TEEDA laminating machine ay may downside, sa unang roll nya meron yung hnd sya mag dikit ng maayos kaya need mo ulit ulit. At baliktarin mo pagka ulit mo. At wag lagi sa gitna ipadaan.
Same case, ang problem is saan maipapaayos ang machine na binakbak?
Sa mga expert machine technician po.
bakit po yhng laminator ko po hindi na uminit ? kakagamit ko lang po lastweek pag gamit ko ngayon hindi na nag laminate
Madami po pwdng dahilan nyan.
Katulad ng:
Hnd gumagana ang outlet.
Kulang ang daloy ng kuryente.
Sumabog ang saksakan.
Kinagat ng pusa o daga ang wire.😅
At higit sa lahat baka may problema ang Iron Plate nya or Heating coil.
Kung okay po ang outlet at saksakan ng laminator nyo. Subukan nyo po ipa On ng 5 to 10 minutes. If wala parin kayong ma feel na init. Kailangan nyo na po ng technician lalo na if wala po tayong idea sa pag repair.
Bakit po ganun yong sa akin bigla po nag stop?
Fist is check the power outlet kung gumagana ba talaga. If yes, at hnd parin init, ipa check mo sa electrician baka nag short-circuit. Kung gumana sya after mo mabili means hnd sya factory damage.
Try mo din mag wait 5 to 10 minutes after mo ma on dun sa "hot". If hnd tagala uminit dalhin mo sa electrician.
J'avais le même problème
@@aminamimi802 I had to translate your message. Anyway, that's how I fixed my machine the first time I encountered such a problem.
इस मशीन ke Soch कहामिलते he
Ye mashine ka gear meljayga
Mine didn't function after opening it 😢
Not functioning like no power?
Make sure you assembled your machine accordingly.
Problem please help me
What happen to your machine brother?
Sem
Hi sir