ไม่สามารถเล่นวิดีโอนี้
ขออภัยในความไม่สะดวก
KS0-PRO HEATSINK INSTALLATION FOR MOSFETS AND THERMAL PASTE REPLACEMENT - 340GH OC
ฝัง
- เผยแพร่เมื่อ 2 ม.ค. 2024
- KS0-PRO HEATSINK INSTALLATION FOR MOSFETS AND THERMAL PASTE REPLACEMENT - 340GH OC
Discord Channel:
/ discord
Disclaimer: This video is not sponsored. I purchased this OC firmware with my own KAS and heatsinks and thermal paster purchsed with my own money. Please remember you may loose your warranty or damage your unit. I don’t take any responsibilities for your hardware. Do your own research if you’d like to take a risk.
Thanks for watching
If interested in purchasing OC contact Tswift
Official Contacts:
Discord: tswiftz
Telegram: @TswiftUSA
Affiliate Amazon links for thermal glue, heatsinks and thermal paste. Thank you for your support.
Alphacool 17425 GPU RAM Copper Heatsinks 6,5x6,5mm (recommended by Tswift)
amzn.to/3TMJsOo
MECCANIXITY Copper Heatsink 6x6x5mm - Used in this video
amzn.to/48ojtBp
GENNEL G109 10gram Thermal Conductive Glue
amzn.to/47hJ3qB
ARCTIC MX-6 (8 g) - Ultimate Performance Thermal Paste
amzn.to/3NP831u
ARCTIC TP-3: Premium Performance Thermal Pad, 100 x 100 x 1.5 mm
amzn.to/3tHw7fL
some parts I used to build my KS0-PRO rig:
Disclaimer:
please do your own research before using any of this hardware for voltage converter, it may as well effect or void your KS0/KS0 PRO warranty or damage the product, this video for entertainment purposes only.
Affiliate Amazon links for KS0 power supply, fan, fan temperature speed controller. Thank you for your support.
HP server PSU
amzn.to/3tbpFxl
Power supply board
amzn.to/489amEq
pcie cables idea but do not recomend using it, I will test them in other video
amzn.to/41fwmv6
pcie power cables:
amzn.to/3t9q8QB
Cllena DC/DC 12V to 19V Boost Converter 20A 480W
amzn.to/3YJG47p
AAOTOKK DC 5.52.5mm to XT60 Adapter Cable Female XT60
amzn.to/3saIShJ
MCIGICM 10 Pair XT60H (XT60 Upgrade)
amzn.to/47HIlEc
OR
Onyehn 4 Pairs 150mm 12AWG Silicon Wire XT60H Plug Male and Female
amzn.to/45gTzy4
2Pcs No Wires Connector XT60 XT-60 Parallel Connector
amzn.to/45i6gsf
HTRC 150A High Precision RC Watt Meter
amzn.to/3QMEfoz
Ancable Replacement 10-Pack 5.5x2.5mm DC Male Plug Power Supply
amzn.to/3E5GLic
Glutoad 50 Pcs Lever Wire Connectors, 1 to 1 Inline Wire Connector Push-in
amzn.to/3KPKiVz
OTHER ITEMS FOR ICERIVER ASICs:
AC Infinity CLOUDLINE PRO T8, Quiet 8”
amzn.to/3GAbgOu
Power cord for KS3L:
amzn.to/3OCMjWa
Smart Home Energy Monitor with 16 50A Circuit Level Sensors
amzn.to/3qHTGU9
AC Infinity MULTIFAN S3, Quiet 120mm USB Fan
amzn.to/3qyKe5C
TOPGREENER Smart Wi-Fi Powerful Plug with Energy Monitoring, Smart Outlet, 15A, 1800W, No Hub Required-
amzn.to/44kHaJ5
PWM Driver Module, DC 12V 24V 48V PWM 4-Wire Fan Temperature Controller Speed-
amzn.to/3PqiDNX
2 fans option - PWM Driver Module, DC 12V 24V
48V 2 Channel 4-Wire Fan Temperature
Controller Speed-
amzn.to/43QA7rd
230W Stealth Charger for MSI GS66 GS65 GS76 GS75 WS65 WS66 WS75 WS76, MSI Laptop Power Adapter Supply
amzn.to/3R4yC3w
Wathai 12038 120mm x 38mm PWM Computer PC Case Fan 12V 4pin 5300rpm High Airflow Duall Ball CFM FG DC Brushless Cooling Fan-
amzn.to/3poxQol
disclaimer:
This is not financial advice and I don’t recommend ordering this miner. This video is for entertainment purposes only. Do your own research.
ice river iceriver kso KSO ks0
![[LIVE] : ONE ลุมพินี 75 | คู่เอก "คมเพชร vs โอมาร์"](http://i.ytimg.com/vi/WugMG7Po8uw/mqdefault.jpg)
Fyi if you're using the gennel g109 thermal glue like tswift recommends its takes about 6 hours for it to cure
yes, had to wait till next day before start 340GH firmware upgrade.
can you post video of hashrate, temps and power usage after adding these thermal pads?
I will, will let it run for 10-15 hours to get a good comparison with other Ks0-pro on 280G before will start going to 340G.
posted
Awesome! Thank you!👍
I’m glad you like it.
fyi, way easier to use the tube of glue and squeeze a dot on the mosfet, then put the little heat sink on top. i used the spreader that comes with the glue to allign the heatsink and squish it down a bit.
Yes, that makes total sense. I was just kinda worry not to be careful enough and spread that glue on other small components besides the mosfets
the size of copper radiators 6*6*5 ?
in the video are 6x6x5 but i used new listed in descriprion that are 6.5x6.5 that work i think even better imo
Thanks for the video. Don't forget to feed your cat!
Thanks. Will do. Haha
Nice brudda, been waiting for my heatsinks, was delayed twice already hahaha. Got everything else tho
Good luck with your upgrades. Not very hard to do but have to be patient and take time as those heatsinks are super small.
@@DontMindMeMining cool thank you!
Well done buddy
Thanks.
Hi, I replaced the cooler with more powerful ones, I would like to show you so you can share more, I couldn't contact you...
Nice, can you share link with your vid?” Here?
Did you use the entire 8g tube of thermal paste for this?
Not for ks0pro, 1.5 tube for KS3M but 1-8g tube I think will be good for about 9-10 ks0pros since it’s only 12 chips on ks0pro and 168 on KS3M
Help. After 20 hours working green and red light are off, fun is working, but hash rate are zero and webInterface not working. Plug power off and on = asic start work again. After 20 hours the problem repeats itself. I have 3 asics and all have same problem. Help!
there are a lot of variances but main one could be mosfets overheating in what you've described, try lower OC and see which one is stable
Hello, question.
have you check how much Watts is your kso pro pulling when close to 300 hashrate?
Yes, it’s in a table of last video. I think about 147W on 12V and 165W of the wall
@@DontMindMeMining I was not aware you could use 12v on the kso pro.
@@piratanet123 I’m using it from day one
need replace mx6 for orinal silicone? if not it can work with 340G ? (just only fix copper heat sink on 4 mosfet)
It’s been instructed by tswift to replace thermal paste and add heatsinks to mosfets in order to get 340Gh OC. Not sure if thermal paste is critical part but it’s been reported that original is bad quality and dries out in a month with high temps when use OC.
Do you know the numbers of th emosfets? i need t find a spec sheet on them
I didn’t take a good photo but there is photos in greater good mining discord channel
nice vid thanks you,Right now how much ur KS0 pro 280 Makes in profit?
Thanks, Right now about 26-27 Kas a day. It’s about $2.6 profit after power on each KS0-Pro.
Why no replace of pads? with better ones?
If you open your ks0-pro and didn’t damage your pads it should work just fine there no requirements for thermal pads but it’s recommended. I didn’t notice a difference so kept them intact.
Hello,
a quick question about the copper coolers. On the video they are clearly lower and smaller? than on the amazon link in the description. Which dimensions are correct?
I tried both of them and they seem to work, I have, the smaller 6x6x5 that are used in the vid are out of stock now and I think the 6.5x6.5 also out of stock I've been waiting for delivery for a week now. any cooper heatsinks that are 6x6 or 6.5x6.5 at the base should work. remember to take photo with your mac address and heatsinks visible in the photo.
they have those heatsinks in stock now, I've added to the description as well.
I have now managed it too,
new heatsinks are glued and also the new thermal paste.
A quick question about the PSU, is the fact that it has 19.5v and the original only 19v not a problem for the board?
Now I have to take care of the firmware itself... @@DontMindMeMining
@@XRaym87X I am using 12V PSU on all of my ks0-pros. I didn’t like much temps with 19V PSU as it gets 3-4C hotter on the sensors.
I have a question...what does it mean "Board Temp(in)" and "Board Temp(out)" ? is temperature from where ? thanks
There is no description where exactly those temp sensors are but temp out is very close to the mosfets so when they got its get high temp reading and temp in probably somewhere at the end of the board closer to power side basically temperature of air entering the ks0pro. Hope that helps.
@@DontMindMeMining thanks for answering
@@DontMindMeMining one more bro...what is the difference between (xxxG_L_ks0pro_update.bgz) and (xxxG_ks0pro_update.bgz) ? why that sequence ? thanks
Low voltage option if you get a silicone lottery and your chips will accept L version is a higher efficiency since using less power
@@DontMindMeMining you are a good guy...thanks...
Nice bro
Appreciate, 😊
Hey do you think that 340gh 24/7 365 is ok ?
That a pretty good question, that what I have with my iceriver box set up. It’s hard to say for summer if I will be able to run it this way or will have to drop it to 280G. I’m checking temps on the chips regularly and so far I’m happy with cooling. As gas the chip life it’s probably will shorten chip life by a lot but this machine maybe worthless in a year when Kaspa hashrate above 400PH never know though.
I didn't understand this 4:17 point here so basicly you just put there Thermal glue i was thinking u gonna put also heatsink :D ...
4:17 is not glue it’s thermal paste on the chips, heatsinks goes onto the mosfets
@@DontMindMeMining I see but u can put also heatsink on the top?
7:20-12:00 in the video for heatsinks to install on mosfets only with glue do not use glue for chips only thermal paste and there is no space for chips to attached heatsinks as ks0pro body is the heatsinks for chips.
Same for non pro ks0?
Non pro doesn’t need heat sinks and only has 4 hashing chips. Thermal paste can be replaced if you see hot temps above 90 on monitoring tool
This 340Gh working on 12 or 19V?
I plan to start with 12V with amp reader to watch the amps at connector and temps. If it gets too hot will switch to 19V for another test and/or will solder silicone wire directly to board like I did in the other vid.