Thank you. Price of this device was Rs.1000/ $6.25 before lock down. Prices may vary after lock down but most probably that would be around Rs. 1000 to 1500 / $ 6.25 to 9.375. according to today's forex rate..
agar agy betry 12v ki yk attached ho to apki wali setting . agar do betries 12v +12v ki hon to setting uski change ho g kia or amp zyada show kary ga then kia soler sy betry ki traf ? main 550 ka soller isky sath lgaya hua
12v ki 2 battries agar, parallel me me lagayain ge tu koi setting change nahi karni hogi, apka battery backup barh jaye ga, aur charing time bhi barhay ga, agar usage ziada hai. Aur agar 12v ki 2 battries series me lagayin ge tu setting change karni hogi, phir apka solar system 24v per kaam kare ga.
@@zoheecorner4749 Ziada Voltage daine lage ga, Agar equipment 12v ke hain tu wo damage ho jayain ge. 12 v ke equipment ke liye parallel hi lagayin battries.
Direct in terminal me lagayain. Battery me na lagayain is tarah apki battery ki life kam ho sakti hai, kion keh ap load bagair kisi controller ke battery se lain ge, jis se battery discharge ziada ho jaye gi aur dead bhi ho sakti hai.
First, Disconnect all connection from controller then connect after 1 minute just battery connection and check all screen and then connect load and check and then connect solar connection and check. If problem is still existed then replace controller.
Ji bilkul de sakte hain hain, laikin behtar hai , inverter input ke liye direct battery se connect kar lain, charger ki life kion kam kar rahay hain, jab iverter se load chala hai tu, aur max 12 volt per 360watt ki out daita hai
Sir v nice explanation. I hav one issue in the same device. At day time vn batteries z full it switched off the load although I’m using load. Then touch the on button. And after 5 mnts it again swtd off the load. How it will give continuous load while batteries are full.
Step 1: Check Panel and output circuit wiring thoroughly and make sure, there shouldn't be any losing in joining and shorting at any point in all circuit. If fault is still existed then go to step 2, Step :2 Disconnect Panel Wire from Controller and run load just with batteries in day time. After performing these steps, you are able to sort out the root cause. Insha Allah.
Charge Battery with any other AC charger from grid power , if battery is charged completely , it's mean you will have to change your solar charge controller and if battery is not charged completely then you have to replace your battery
Bilkul kar sakte hain, laikin ye long term me circuit ke liye theek nahi hai, Fan kisi achi brand ka use karain 12 volt per bhi buhat achi speed hoti hai
@@dr.zeeshanmirza 12 volf solar ke per chalne ke liye, khurseed aur Taimoor ke fan best hai, GFC ka main ne use nahi kia hai is liye uska main kuch nahi keh sakta, aur GFC ka naam 220 lv me tu hai, laikin 12 volt me itna nahi hai, jitna khusheed ya Raimoor ka hai, Aur agar ap filhal change nahi karna cha rahay hain, tu is fan ko kisi fully charged new 12 volt battery ke sath chala kar check karain kia result aata us se sahi examine ho jaye ga, Bhai.
Sir iske output point per voltage test karke batawo battery full honey per sayad yeh solor voltage ko bypass kar deta hai aur hamari led light falekvhuwet karti hai jo tik nahi hai.
Nahi aisa nahi hai, ye aisa nahi karta hai, output per stable voltage milte hain , jo battery se hi aati hai, agar aisa ho tu apke equipments damage ho jayain ge , jal jayain ge ziada voltage ki wajah se, kion keh peak time per voltage tu 21, 22 volt per bhi jate hain, jo 12 volt ke equipment ko foran burn out kar de ga, ap connection check karo kahin koi losing hogi, ya phir controller ke output points bhi undar se lose ho sakte hain ,ye check karain
Hi there I'm using the same device but with other label :p I'm facing a issue, on home screen my voltage are fluctuating sometimes around 19V. I've changes the settings to minimum values and also yours but still remains the issue. Any help will be appreciated!
Oh i forgot to mention I'm using my load through a relay so i get current only during load shedding. By running load the Volt fluctuations become lesser then before. Is this device issue or battery!
Hi, There are a lot of issues that can cause this problem. Some questions are arisen here; 1- Are you running the device either on 12 volt or 24 volt? 2- Which solar plates are attached with the device either 12 volt or 24 volt ? 3- How many watts, do you have in solar plates those are attached with the device and all plates all working fine? 4- How's your battery bank and all battery in your battery bank is working fine ?, etc.... Anyways, If everything is fine then you should check and verify your battery voltage and panel voltage separately with a Multi-meter or any DC volt Meter and check battery health and should also check the output voltage of the device at the time of fluctuation without any load on output circuit. If every thing is OK on Multi-meter or DC volt meter then you should ignore this issue and If Multi-meter or DC volt meter is also showed the same problem. It's mean device is malfunctioning you should replace the Device. Thanks,
I'm running 12V current.. Its 150Watt plate I've done through with almost all above procedures.. I'll check the reading with DC metter tomorrow morning.. Probably i may have to replace the device :( Thanks for your help
Ji, Ap isko 2 batteries se bhi laha saktay hain, 2 batteries parallel me connect kardain, yani aik battery ka positive dosri battery ke positive se aur dosri battery ka positive controller ke positive me , aisa same negative ke liye kardain tu ye parallel connection ho jaye ga,
Matching se setup karain, ya pora setup 24 volt ka banayain ya 12 volt ka. Battery aur Charger dono save rahain ge long time ke liye. dono cheezain same kar lain, ya panel 12 volt ka laga dain ya aik battery barha kar battery side bhi 24 volt ki kar dain. Aur out put per Converter laga kar 12 volt supply le lain,
Mere pas 1 plate hai 165 aur betry 100w ki hai mai din ko betry plate se direct charge krta hun aur rat ko solar fan on krta hun kia aisa krna sahi hai is mein agr mazeed koi chez add krni hai tu wo bta den,?
Ap is ke sath charge controller laga lain zaroori hai, kion keh direct charge karne se battery overcharge ho sakti hai, battery life kam ho jati hai is tarah se.
Yes but not recommended. It's not working properly with high wattage single panels. You can attach low wattage panel in series to run it on 24 volts for better performance.
aik battery ke positive ko dosri battery ke positive se, is hi tarah negative ko negative se jorain, aur phir controller ke negative , positive battery ke negative , positive se jor dain, is tarah parallel connection ke through 12v ke sath ziada amps ka backup le sakain ge,
A.o.a sir I have same device on my solar system.i have set power cut on 14.5 but my voltage do not increase by 13.1 what is the problem ...infact every thing is ok
Hello sir I have 4 solar panels of 150 watt individually. I use AGS tubular tall battery 1800. My voltage on screen shows 13 or 13.2. should I maximize it to 14.4?
It can support up to 720 watts with 24 volt setup and 360 watts with 12 volt setup but It is recommended that you have to use 50 to 60 % load for continuous load and to 70 to 100% load for short term use.
Sir .maine amperes plates par ampere meter se check kia hai 20 ampere a rhe hain.lekin controler main hamesha kam show hote hain.iski waja ?. Controler 60amp sogo ka hai
Aise batana tu buhat mushkil hai kion keh is me buhat sari cheezain hain jis ki wajah se difference asakta hai. Ap ne check kaise kia hai ?, Solar plate kitne watt ki hai ?, Check karne ka time kia tha ?, Check karte hoye solar plate ka latitude angle kia tha ?, Weather Sunny tha, partial Cloudy tha ya phir full cloudy tha? Temperature kia tha ?, Phir ap jis amp meter se check kia wo kaisa hai, wo theek kaam Kar raha hai, local hai ya branded hai ?, etc...
Same model controller I'm using I connected panel first for 3-4days as I didn't knew panel have to connected in last. When I Connected battery it worked fine for a min or 2. But now it's screen is stuck at voltage which shows 1.1v and angry face image. I have a 30w dc ceiling fan which I connected directly to the battery. Is it OK to connect DC load directly to the battery or should I connect my DC load to charge controller? Pls help. Thanks
Yes you can use DC load directly from battery but you shouldn't connect DC load from Panel directly because 12 volt panel system voltage is touched the voltage upto 20 to 21 volt in day time and that can damage your equipments.
Agar working sahi ka raha hai tu isay ignore kar dain , koi maslay wali baat nahi hai, aur agar koi physically current ya charing me bui issues start ho gaye hain tu charger replace kar dain
AoA sir mere pas 3 DC fans hai. Tu me controller k load se aik main wire le lo per us se 3no fans connect karlo. Ya per 3no fans k wires aik sat controller k load se connect karlo thanks....
Agar tino fans controller ke qareeb hi hain tu behtar hai keh alag alag wire controller tuk le jayain, is me apko ko kam gauge ka wire use karna paray ga jo price ke hisab se sasta parta hai , aur agar controller tino se qareeb nahi hai tu ap aik wire le jayain laikin wo wire 16 mm ya kam az kam 10 mm ka ho, tu hi voltage poray milain ge, otherwise voltage buhat drop ho jayain ge aur fans buhat slow run karay ga,
12 volt and 24 volt dono per kaam karta hai ye controller. Agar ap 12 volt ka setup karna chate hain tu 12 volt ka panel lagayain , jo normally 18 to 22 v tuk ouput daita hai
Baqi Setting kaam kar rahi hain? Agar remaining settings bhi issue kar rahi hain tu multimeter se recheck karain, battery voltage aur meter se kia volts in out ho rahe hain, agar wo bhi theek nahi hain tu , apko controller replace karna hoga
Salam, Mere pass cm3024z controller hai, us per Chand ( moon ) display per araha hai aur charging ampere nhy arahe... Plz guide krden k Kiya problem Hy...
Walaikum-as-Salam, Battery Charge ho rahi hai ?, Battery charging kisi volt meter se check kar ke confirm karain, agar wo ho rahi hai proper tu baqi indications ko ignore kar dain,
Hi Sir How to connect temperatures sensor cable It's have two cable or one cable??? Which battery terminal we connect the sensor cable?? Could you please explain above mentioned iteams
There is no need to connect any separate temperature sensor. This model has built-in tempreture sensor. Yes, We had to attach a separate temperature sensor in previous model that was attached on the top side of the charge controller.
Sir kya hum electric charger sy connector k through battery charge kr sakhty hain..in case of agr solor system main koi fault aye..aur battery charge na hon .. Ya night k time zarorat k waqt battery ko kese bijli sy charge krynge 🤔
@@abdussami2588 Yes, Jaisa app jantay hain waisa hi, Charger ke positive aur negative connectors battery ke positive aur negative terminals ke sath connect kar dain, charger ke amp ko battery ke mutabiq set kar dain , battery charge hona shoro ho jaye gi, aur apnay voltage tuk charge honay per charger off kar dain,
Salam mjhe ek bat pochni thi mere pas b charg controlar hai but battery se + ki tar controlar may laga rha hn on nh ho rhi h - tar controlar may + may laga rha hn tu on ho rhi h ok 2 problem ye hai solar show ho rha h likn teer may biling nh ho rha h sirf teer show ho rha h is k matlb ye h solar se battery may current nh aa rha h hai
Daikhain is device ki market me buhat si copies mil rahi hain, original device aisay problems nahi karti hai, copy devices me problems hoti hain, agar device kaam sahi kar rahi, means voltage aur current wagaira proper de rahi hai sirf display ka aur +\- marking ka problem hai tu chalne de, other devic change kar lain aur kisi reliable shop se purchase karain, aur purchase karte hoye shop per hi sub features shopkeeper se check karwa kar lain,
Mera load ziyada hai, battery kuch din baad discharge ho jati hai, ager main panels ke saath koi charger bi use karna chaho tu kese karon? Panels wali soget main charger bi laga lon?
Nahi, Bhai. Panel walay socket me charger nahi laga lijiye ga, Device kharab ho jaye gi, Agar aisa masla hai tu direct battery per charger ki clips attach kar ke battery ko direct charger se charge karain,
Nishan na aana koi masla nahi hai screen fault ya display fault bhi ajata hai kabhi. Ap kisi multimeter ya volt meter aur Ammeter se panel ke voltage aur current check karain agar voltage aur current sahi arahay hain tu, sub set hai. Panel ke nishan ko ignore kar dain. Agar voltage aur current sahi nahi arahay hain, tu ap device replace kar lain. Thanks
@@mvcknowledge8547 thank u dear magar panal ke nishan bi nahi araha aw wo ter ka nishan me jo bijle janae ka nishan hita hy wo bi nahi araha bro ap apna whatsapp nmber de sakte ho me pict le ke whatsapp karta ho
No, You can also use these settings for tubular batteries. Tubular Batteries's Charging are also lain between 13.4v or 13.5v to 15.9v or 16.1v for stand by and cycle use.
ak problem aa rahi solar charge controller par. charging karta hai tu load off ho jata hai auto. yani load blank ho jata. aur agar charging off karo tu load on ho jata hai. please kuch batye kya problem hai?
Apke saray msgs parhe , saray msgs parhne ke baad mujhe aisa lagat hai apki device theek kaam nahi kar rahi hai, app device change kar lain , Saray problems solve ho jayain ge,
Walaikum-as-Salam, Nahi fake nahi hai wo bhi is series ka aik model hai, name same hi hai laikin price different hoti hai, wo price me kuch kam hota hai, us me Amp show nahi hotay, baqi same hi hai wo aur same working karta hai. Market me dono available hain ap Amp wala market se check karwa kar le saktay hain
@@mvcknowledge8547 bhaee change Kar lo ya yh b teek hy siraf amp ka ni Pata lagta panel kitnay day ra hy 170 watt Japan solar panel hy koi suggest Kar dain ya DC meter say panel ki wire jor KY reading lay lo
@@mvcknowledge8547 1000 ka Dia hy shopkeeper nay MA nay Rasheed daki hy bat ki te fon pay khta hy kuch pasay kat Kay change Kar data hy lay aow ap mashwara dain kuchen
@@flower7862 Agar ap reqular Amp check karna chatay hain, aur amps ko properly monitor karna chatay hain tu change kar lain amps wala le lain , otherwise is ko chalnay dain ye bhi theek hai.
@@mvcknowledge8547 جناب میراکنٹرولرجب بیٹری سےکنکٹ کرتاہوں بیٹری ولٹ اٹھ دیکھاتاہے اور جیسےسولرکنکٹ کرتاہوں توبارہ شوکرتاہے اور میں نےلوڈاف دس پر رکھاہے اور دوسری بات یہ کہ سولرسےدس منٹ تک ایمپیراتےہیں پھرخودبخودبند ہوجاتےہیں جب دوبارہ کنکٹ کرتاہوپھرسےشروع ہوجاتےہیں یہ کیامسلہ ہےپلیز
@@faizurehman2464 Ap kisi achay multimeter ya volt meter se direct battery voltage check karain?, battery voltage meter per kia show ho rahay hain ?, aur agr koi aur dosri achi condition me battery hai tu wo replace kar ke daikhain.
Is controller ka subsay bada masla hai shayad ue masla tamam controller. Aj hota hoga masla.ye hai amp down kar deta hai agar 10 amp solar say aa rahay to 2 amp lost hojata controller mai koi aesa ctroller hai Jo amp ko.loss k bajaye increase karay
Ideally, aisa nahi hona chahiye, load ON ya OFF karne se battery ki charging ka koi tallauq nahi hai is device me, app connections verify karain, otherwise device change kar lain ,
Volt meter se solar panel ke voltage check karain, aue battery charing ya load ON per amp check karain , gar wo OK hain tu , No Problem. Sirf Display ka issue us se koi farq nahi parta.
Arrow na chalna masla nahi hai, masla charing hona ya na hona hai, multi meter se check karain, kabhi aisa bhi hota hai keh arrow show nahi ho raha hon, laikin device proper kaam kar rahi hoti hai
Walaikum-as-Slam, ap jis hole ki baat kar rahay hain wo is model me nahi hai ye baad ka model hai is me wo function built-in kar diya gaya hai. Wo basically Temperature Sensor hota tha, wo puranay models me aata tha, jo ab alag se nahi lagta ab built- in hota hai. Shukriya.
This question clear my all questions.
Thanks alot and keep it up
Thanks bohat achey tareky say sam jaya ap nay
thanks your video have been strong help to me
Thanks a lot... Your video have been a great help to me... I really appreciate your effort
Bhai mera controlar amp show nhi kr rha hai
Is controller ke 2 veriants hain, aik me amp show hota jai, aur aik me nahi ,tu ap ne without amp ka meter lia hoga
thanks bro, love you,
Welcome
Very nice brother
❤❤❤osam bro
Very nicely explained....
Wow to good Bahi
Thank you so much
vary good sir nice video ❤❤❤
Well DONE
Thank you
Very good sir detailed
Thank you.
Price of this device was Rs.1000/ $6.25 before lock down. Prices may vary after lock down but most probably that would be around Rs. 1000 to 1500 / $ 6.25 to 9.375. according to today's forex rate..
agar agy betry 12v ki yk attached ho to apki wali setting . agar do betries 12v +12v ki hon to setting uski change ho g kia or amp zyada show kary ga then kia soler sy betry ki traf ? main 550 ka soller isky sath lgaya hua
12v ki 2 battries agar, parallel me me lagayain ge tu koi setting change nahi karni hogi, apka battery backup barh jaye ga, aur charing time bhi barhay ga, agar usage ziada hai. Aur agar 12v ki 2 battries series me lagayin ge tu setting change karni hogi, phir apka solar system 24v per kaam kare ga.
@@mvcknowledge8547 series main lgany sy zyada amp dyny lag jay ga load ko ??
@@zoheecorner4749 Ziada Voltage daine lage ga, Agar equipment 12v ke hain tu wo damage ho jayain ge. 12 v ke equipment ke liye parallel hi lagayin battries.
Sir mera solar comtroller 12.9 py aa kar ruk jata hai aue setting bi ni ho rahi.button ko long press bi kea lekan koi asar nai ho raha
Controller Replace ya repair karwa lain, controller ka masla hai
Sir jb hm load p kuch b use krty hain to ye bht gram ho jata h ...Or load p 12v ka fan b bht slow chlta h or device b bht grm ho jati h
thank you!
Welcome
Bhai solar se direct load is divce se chal sakta he
No, Battery Lagana Zaroori hai. Agar Solar se Direct chalana hai tu, DC to DC stablizer, coverter aata hai us se chal jaye ga,
Thanks Bhai converter Kon sa lon
Bhai panel ki jaga desi ups ke charger ke terminal lagasakte hai?
Agar panel use nahi karnay hain tu Direct UPS se hi chala lain, Controller kion laga rahay hain circuit me ?
@@mvcknowledge8547 overcharge protection klye qk desi ups mai ye functionality nahi hai.
@@thezubairrahim Ok, daikhain kar tu saktain hain ap aisa laikin ye recommended nahi hai. Long term me device damage bhi ho sakti hai.
@@mvcknowledge8547 ok thanks
ماشاء اللّٰہ
60 amp Battery charger ki output ko charge controller ma is a soller laga saktha hai
Good Information 👍👍👍
Thank you ,great knowledge
Sir mera pass same controller hi but output load nhi de raha hi plz guide me
Bhai ye jo do terminal hain fan ya blub ke liye to fan ki taaren direct ise main lagade ya bettery main....?
Direct in terminal me lagayain. Battery me na lagayain is tarah apki battery ki life kam ho sakti hai, kion keh ap load bagair kisi controller ke battery se lain ge, jis se battery discharge ziada ho jaye gi aur dead bhi ho sakti hai.
Very nice
Dear same controller installed at my home but screen stuck on Ah and PV hours no any button works what should I do guide me plz Thanks
First, Disconnect all connection from controller then connect after 1 minute just battery connection and check all screen and then connect load and check and then connect solar connection and check. If problem is still existed then replace controller.
@@mvcknowledge8547 Thank you for suggestion but issue resolved due to help of your video Thanks
Out put dc volt ko invertor main laga kar 220 ac le sakte hain or ye kitne watt ka load de sakta hai
Ji bilkul de sakte hain hain, laikin behtar hai , inverter input ke liye direct battery se connect kar lain, charger ki life kion kam kar rahay hain, jab iverter se load chala hai tu, aur max 12 volt per 360watt ki out daita hai
thanks bhaiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
Just pv off hour load off on or battery temp hy is ki setting ko press karnay pay
pv say kitnay amp aray hn yh option ni hy or baki b
JZAK ALLAH
Sir charging on settings b hoti hai??
Yes,
Sir v nice explanation. I hav one issue in the same device. At day time vn batteries z full it switched off the load although I’m using load. Then touch the on button. And after 5 mnts it again swtd off the load. How it will give continuous load while batteries are full.
Step 1:
Check Panel and output circuit wiring thoroughly and make sure, there shouldn't be any losing in joining and shorting at any point in all circuit.
If fault is still existed then go to step 2,
Step :2
Disconnect Panel Wire from Controller and run load just with batteries in day time.
After performing these steps, you are able to sort out the root cause. Insha Allah.
Nice
I have 2 solar panels of 150 watt but my tublar battery is not full charging going maximum to 12.8. Or13.0 what i should do
Charge Battery with any other AC charger from grid power , if battery is charged completely , it's mean you will have to change your solar charge controller and if battery is not charged completely then you have to replace your battery
Bhai kaya Pwm Sa Load Lay Saktay Ha Jab Battery Charge Hori Ho ups Par
Yes, No issue. Charge and Load are worked simultaneously on it.
Sir kaya controller ki output 12 say 14volts karsaktay hain kyun k dc ceilling fan slow chal rahay hain ?????
Bilkul kar sakte hain, laikin ye long term me circuit ke liye theek nahi hai, Fan kisi achi brand ka use karain 12 volt per bhi buhat achi speed hoti hai
@@mvcknowledge8547 gfc k fan lia hain.iss say bhee achee koee cpmpany hay kaya???
@@dr.zeeshanmirza 12 volf solar ke per chalne ke liye, khurseed aur Taimoor ke fan best hai, GFC ka main ne use nahi kia hai is liye uska main kuch nahi keh sakta, aur GFC ka naam 220 lv me tu hai, laikin 12 volt me itna nahi hai, jitna khusheed ya Raimoor ka hai,
Aur agar ap filhal change nahi karna cha rahay hain, tu is fan ko kisi fully charged new 12 volt battery ke sath chala kar check karain kia result aata us se sahi examine ho jaye ga, Bhai.
Service available in Karachi?
Sir iske output point per voltage test karke batawo battery full honey per sayad yeh solor voltage ko bypass kar deta hai aur hamari led light falekvhuwet karti hai jo tik nahi hai.
Nahi aisa nahi hai, ye aisa nahi karta hai, output per stable voltage milte hain , jo battery se hi aati hai, agar aisa ho tu apke equipments damage ho jayain ge , jal jayain ge ziada voltage ki wajah se, kion keh peak time per voltage tu 21, 22 volt per bhi jate hain, jo 12 volt ke equipment ko foran burn out kar de ga, ap connection check karo kahin koi losing hogi, ya phir controller ke output points bhi undar se lose ho sakte hain ,ye check karain
Hi there
I'm using the same device but with other label :p
I'm facing a issue, on home screen my voltage are fluctuating sometimes around 19V. I've changes the settings to minimum values and also yours but still remains the issue.
Any help will be appreciated!
Oh i forgot to mention I'm using my load through a relay so i get current only during load shedding.
By running load the Volt fluctuations become lesser then before.
Is this device issue or battery!
Hi,
There are a lot of issues that can cause this problem. Some questions are arisen here;
1- Are you running the device either on 12 volt or 24 volt?
2- Which solar plates are attached with the device either 12 volt or 24 volt ?
3- How many watts, do you have in solar plates those are attached with the device and all plates all working fine?
4- How's your battery bank and all battery in your battery bank is working fine ?,
etc....
Anyways,
If everything is fine then you should check and verify your battery voltage and panel voltage separately with a Multi-meter or any DC volt Meter and check battery health and should also check the output voltage of the device at the time of fluctuation without any load on output circuit.
If every thing is OK on Multi-meter or DC volt meter then you should ignore this issue and If Multi-meter or DC volt meter is also showed the same problem. It's mean device is malfunctioning you should replace the Device.
Thanks,
I'm running 12V current..
Its 150Watt plate
I've done through with almost all above procedures..
I'll check the reading with DC metter tomorrow morning..
Probably i may have to replace the device :(
Thanks for your help
@@sizulabs Thanks. You are welcome.
100w panel kaam carega sir hema bataye 30A controller me
Yes, Off course. Bikul karay ga.
Kia isay 2 batteries se bhi lagta saktay hain ,us ki setting baat den
Ji, Ap isko 2 batteries se bhi laha saktay hain, 2 batteries parallel me connect kardain, yani aik battery ka positive dosri battery ke positive se aur dosri battery ka positive controller ke positive me , aisa same negative ke liye kardain tu ye parallel connection ho jaye ga,
sir mera panel 24 voltage ka ha
mene 12 voltage ki battery raki ha
or Sogo ka solar charger lagaya ha
battery protection possible ha
Matching se setup karain, ya pora setup 24 volt ka banayain ya 12 volt ka. Battery aur Charger dono save rahain ge long time ke liye.
dono cheezain same kar lain, ya panel 12 volt ka laga dain ya aik battery barha kar battery side bhi 24 volt ki kar dain. Aur out put per Converter laga kar 12 volt supply le lain,
Mere pas 1 plate hai 165 aur betry 100w ki hai mai din ko betry plate se direct charge krta hun aur rat ko solar fan on krta hun kia aisa krna sahi hai is mein agr mazeed koi chez add krni hai tu wo bta den,?
Ap is ke sath charge controller laga lain zaroori hai, kion keh direct charge karne se battery overcharge ho sakti hai, battery life kam ho jati hai is tarah se.
@@mvcknowledge8547 Acha betry charger lgana tu zaroori ni yh betry rat nikal jye gi,?
@@actionblaster1738 Yes, Average Charger laga lain koi sa
@@mvcknowledge8547 okay
Why erows are not blinking on charger
@mvc can we attach 38V 340w panel to this controller
Yes but not recommended. It's not working properly with high wattage single panels. You can attach low wattage panel in series to run it on 24 volts for better performance.
Bhaijaan agar hamare pas 2 battery ha to unko kese connect krenge controller se 12v dc system k liye
aik battery ke positive ko dosri battery ke positive se, is hi tarah negative ko negative se jorain, aur phir controller ke negative , positive battery ke negative , positive se jor dain, is tarah parallel connection ke through 12v ke sath ziada amps ka backup le sakain ge,
@@mvcknowledge8547 thank you so much
@@mvcknowledge8547 bhaijaan controller ka jo output ha waha se saree ghar k fan or lights sahi se chalege ya battery se laga dain to better rahega
@@hafeezkandhro419 controller ke output se hi lagayain, is trah apki battery safe rahay gi , uski life bhi ziada hogi,
@@mvcknowledge8547 usse fan wagera slow nahi hoga agar sara load on rahega to?
Ya battery full s charg ho to Raat kb tk chaly gha
A.o.a sir
I have same device on my solar system.i have set power cut on 14.5 but my voltage do not increase by 13.1 what is the problem ...infact every thing is ok
Walaikum-as-Salam,
There could be many reasons. Weak or Damage Battery, problem in solar plates or input wiring from solar plates, Controller Probelm.
Good work but Too much long video
Please bhai ye batao ke
Solar ki jaga charger connect karsakte hai
Yes, WHY NOT. but that would'nt be a solar system. That will be a 12 volt DC system .
Hello sir
I have 4 solar panels of 150 watt individually. I use AGS tubular tall battery 1800. My voltage on screen shows 13 or 13.2. should I maximize it to 14.4?
It depends on your usage. Do you depend fully on solar electric or seldom ?, If you depends on solar elecric completely, you may. Otherwise no need.
is mae ampere control ni hotae apki battery khrab ho jye gi jld
What is the recommended load to be connected with charge controller in watts?
It can support up to 720 watts with 24 volt setup and 360 watts with 12 volt setup but It is recommended that you have to use 50 to 60 % load for continuous load and to 70 to 100% load for short term use.
ماشاءاللہ بہت خوب جتنی تعریف کی جائے کم ہے شاندار ویڈیو بنائی ہے کیا آپ کا واٹس ایپ نمبر مل سکتا ہے
Sir .maine amperes plates par ampere meter se check kia hai 20 ampere a rhe hain.lekin controler main hamesha kam show hote hain.iski waja ?. Controler 60amp sogo ka hai
Aise batana tu buhat mushkil hai kion keh is me buhat sari cheezain hain jis ki wajah se difference asakta hai.
Ap ne check kaise kia hai ?,
Solar plate kitne watt ki hai ?,
Check karne ka time kia tha ?,
Check karte hoye solar plate ka latitude angle kia tha ?,
Weather Sunny tha, partial Cloudy tha ya phir full cloudy tha?
Temperature kia tha ?,
Phir ap jis amp meter se check kia wo kaisa hai, wo theek kaam Kar raha hai, local hai ya branded hai ?, etc...
Meme new controller lya he wo automatic load off nh kar rha kya masla he
Setting kia ki hain ap ne, uski details batayain ?
Same model controller I'm using
I connected panel first for 3-4days as I didn't knew panel have to connected in last. When I Connected battery it worked fine for a min or 2. But now it's screen is stuck at voltage which shows 1.1v and angry face image. I have a 30w dc ceiling fan which I connected directly to the battery.
Is it OK to connect DC load directly to the battery or should I connect my DC load to charge controller?
Pls help. Thanks
Yes you can use DC load directly from battery but you shouldn't connect DC load from Panel directly because 12 volt panel system voltage is touched the voltage upto 20 to 21 volt in day time and that can damage your equipments.
Iske sath 570 watt ka solar laga sakty h?
No, Brother. For 570 watt , you will have to use atleast 50 amp controller and I will recommend 70 to 100 amp controller dueto load balancing.
Sir ma JB load ko on krta hn aur 12 v ka LED on krta hn to tb battery charge
Sorry, couldn't get you. Explain it completely.
Sir din time b mery panel py chand ☪️ or solar ka neshan ata hy Kabi jata hy. Oapr sy jo wire ati Wo b thek hy crunt a rha hy
Agar working sahi ka raha hai tu isay ignore kar dain , koi maslay wali baat nahi hai, aur agar koi physically current ya charing me bui issues start ho gaye hain tu charger replace kar dain
AoA sir mere pas 3 DC fans hai. Tu me controller k load se aik main wire le lo per us se 3no fans connect karlo. Ya per 3no fans k wires aik sat controller k load se connect karlo thanks....
Agar tino fans controller ke qareeb hi hain tu behtar hai keh alag alag wire controller tuk le jayain, is me apko ko kam gauge ka wire use karna paray ga jo price ke hisab se sasta parta hai , aur agar controller tino se qareeb nahi hai tu ap aik wire le jayain laikin wo wire 16 mm ya kam az kam 10 mm ka ho, tu hi voltage poray milain ge, otherwise voltage buhat drop ho jayain ge aur fans buhat slow run karay ga,
@@mvcknowledge8547 thankx g
Is ma sir pannel kitny v ka hona chahey
12 volt and 24 volt dono per kaam karta hai ye controller. Agar ap 12 volt ka setup karna chate hain tu 12 volt ka panel lagayain , jo normally 18 to 22 v tuk ouput daita hai
Sir yeh panel ka sign jb hatt jata hai tw battery ka volt direct neche gir jata hn ..kia masla hai yeh ..mtlb jaisa he solar band hota ha tb
Ye normal hai, koi masla nahi hai. Agar solarka sign jane ke baad, voltage 12.9 ya 13.0 show kar raha hai tu battery full charge hai.
Mere pas yahi controller hai per 13.8 se uper ni jraha hai me chahata ho k 14.5 tk hojye to ab me kia kru ???
Baqi Setting kaam kar rahi hain? Agar remaining settings bhi issue kar rahi hain tu multimeter se recheck karain, battery voltage aur meter se kia volts in out ho rahe hain, agar wo bhi theek nahi hain tu , apko controller replace karna hoga
Salam,
Mere pass cm3024z controller hai, us per Chand ( moon ) display per araha hai aur charging ampere nhy arahe... Plz guide krden k Kiya problem Hy...
Walaikum-as-Salam,
Battery Charge ho rahi hai ?, Battery charging kisi volt meter se check kar ke confirm karain, agar wo ho rahi hai proper tu baqi indications ko ignore kar dain,
Hi Sir
How to connect temperatures sensor cable
It's have two cable or one cable???
Which battery terminal we connect the sensor cable??
Could you please explain above mentioned iteams
There is no need to connect any separate temperature sensor. This model has built-in tempreture sensor. Yes, We had to attach a separate temperature sensor in previous model that was attached on the top side of the charge controller.
Sir may aap ke setting dekh kr apnay controller ke setting kr magar mera output bar bar disconnect ho kr chalte hay
Controller issue. Please, Replace Controller.
24 volte pr setting ha is ki
24 volt per jo settings rakhni hai wo video ki last me batai hai. Wo set kar sakte hain ap
Hi, support lithium?
Yes, but not recommended.
Kia is ko return Kar do shop keeper ko mashwara dain ya change karwa lo
Sorry, couldn't get you.
Har thori dair bad load off ho jata he kia waja ho sakti he
80% Controller problem ho sakta hai, Controller change kar ke check karain,
Salam yei device hai mere pas
Lekin front screen pe solar panal se current ata show nhi ho rha us arrow main
Walaikum-as-Salam,
Sirf show nahi ho raha hai tu koi masla nahi hai, kisi amp meter se check karain , working fine hai tu , no issue
😢sir solar connect hone k bawajood moon ka nishan a raha hai din me bhi solution plz
Sir kya hum electric charger sy connector k through battery charge kr sakhty hain..in case of agr solor system main koi fault aye..aur battery charge na hon ..
Ya night k time zarorat k waqt battery ko kese bijli sy charge krynge 🤔
Yes, Bilkul kar sakte hain. Aur behtar hai ke night ke time per karain.
@@mvcknowledge8547 to aap mujhe guide kr sakhty hon kh kese krynge?
@@abdussami2588 Yes, Jaisa app jantay hain waisa hi, Charger ke positive aur negative connectors battery ke positive aur negative terminals ke sath connect kar dain, charger ke amp ko battery ke mutabiq set kar dain , battery charge hona shoro ho jaye gi, aur apnay voltage tuk charge honay per charger off kar dain,
@@mvcknowledge8547 thank u bhai jan
Salam mjhe ek bat pochni thi mere pas b charg controlar hai but battery se + ki tar controlar may laga rha hn on nh ho rhi h - tar controlar may + may laga rha hn tu on ho rhi h ok
2 problem ye hai solar show ho rha h likn teer may biling nh ho rha h sirf teer show ho rha h is k matlb ye h solar se battery may current nh aa rha h hai
Daikhain is device ki market me buhat si copies mil rahi hain, original device aisay problems nahi karti hai, copy devices me problems hoti hain,
agar device kaam sahi kar rahi, means voltage aur current wagaira proper de rahi hai sirf display ka aur +\- marking ka problem hai tu chalne de, other devic change kar lain aur kisi reliable shop se purchase karain, aur purchase karte hoye shop per hi sub features shopkeeper se check karwa kar lain,
Mera load ziyada hai, battery kuch din baad discharge ho jati hai, ager main panels ke saath koi charger bi use karna chaho tu kese karon?
Panels wali soget main charger bi laga lon?
Nahi, Bhai. Panel walay socket me charger nahi laga lijiye ga, Device kharab ho jaye gi, Agar aisa masla hai tu direct battery per charger ki clips attach kar ke battery ko direct charger se charge karain,
Dear mera ye panal ka nishan nahi araha pehly tek ta ab pata nahi kaha ghyb hogaya he ar rat ka nishan araha he. Plz help
My whatsap number is 03449665466
Nishan na aana koi masla nahi hai screen fault ya display fault bhi ajata hai kabhi.
Ap kisi multimeter ya volt meter aur Ammeter se panel ke voltage aur current check karain agar voltage aur current sahi arahay hain tu, sub set hai. Panel ke nishan ko ignore kar dain.
Agar voltage aur current sahi nahi arahay hain, tu ap device replace kar lain.
Thanks
@@mvcknowledge8547 thank u dear magar panal ke nishan bi nahi araha aw wo ter ka nishan me jo bijle janae ka nishan hita hy wo bi nahi araha bro ap apna whatsapp nmber de sakte ho me pict le ke whatsapp karta ho
Tubler battery k leay ye settings nhe Hain I think ??
No, You can also use these settings for tubular batteries. Tubular Batteries's Charging are also lain between 13.4v or 13.5v to 15.9v or 16.1v for stand by and cycle use.
ak problem aa rahi solar charge controller par. charging karta hai tu load off ho jata hai auto. yani load blank ho jata. aur agar charging off karo tu load on ho jata hai. please kuch batye kya problem hai?
Replace kar lain,
Please reply kijiye ga..♥️
Apke saray msgs parhe , saray msgs parhne ke baad mujhe aisa lagat hai apki device theek kaam nahi kar rahi hai, app device change kar lain , Saray problems solve ho jayain ge,
60 ampere main solar battery Kitni honi chahie and bulb Jala sakte hain
Ap ki requirement per depend karta hai ap ko kitnay backup ki zarorat hai aur apka din aur raat ka load kitna hai.
Load is AC load or DC Load
Obviously, DC load.
1200 ka purchased Kia hy 15 din phlay
Aoa maray pa's is controler MA Amp ni batata Kiya waja ho sakti hy option hi ni hy model number yahi Kia yh fake controller hy
Walaikum-as-Salam, Nahi fake nahi hai wo bhi is series ka aik model hai, name same hi hai laikin price different hoti hai, wo price me kuch kam hota hai, us me Amp show nahi hotay, baqi same hi hai wo aur same working karta hai. Market me dono available hain ap Amp wala market se check karwa kar le saktay hain
@@mvcknowledge8547 bhaee change Kar lo ya yh b teek hy siraf amp ka ni Pata lagta panel kitnay day ra hy 170 watt Japan solar panel hy koi suggest Kar dain ya DC meter say panel ki wire jor KY reading lay lo
@@mvcknowledge8547 1000 ka Dia hy shopkeeper nay MA nay Rasheed daki hy bat ki te fon pay khta hy kuch pasay kat Kay change Kar data hy lay aow ap mashwara dain kuchen
@@flower7862 Agar ap reqular Amp check karna chatay hain, aur amps ko properly monitor karna chatay hain tu change kar lain amps wala le lain , otherwise is ko chalnay dain ye bhi theek hai.
volt to set ho gaye ampere kese set krain kae 20a sae charge ho na kar 50 40a
amp auto per set hota hai, manually is per amp setting change nahi kar sakte, ap voltage set karain amp automatically set ho jaye ga,
جب سولر پلیٹ اٹیچ ہو اور لوڈ أن ہو تو یہ لوڈ سولر سے چلتا ہے یا بیٹری سے؟
سولر سے۔
Or agar battery connected na ho or sirf solar panels connected hon tou yeh device DC load Chala lega without battery ??
Sir kia kingway ka cm 3024Z aur ye aik hy ya alag alag hy
Yes, Same interfaces in some models of Kingway. Just Label differences.
@@mvcknowledge8547 ok thanks
Sir my ne khared lia hy to kia rat ko ye charage solar ki taraf to nhe jayega
@@faizurehman2464 No, Reverse Protection hoti hai chargers me.
@@mvcknowledge8547 جناب میراکنٹرولرجب بیٹری سےکنکٹ کرتاہوں بیٹری ولٹ اٹھ دیکھاتاہے اور جیسےسولرکنکٹ کرتاہوں توبارہ شوکرتاہے اور میں نےلوڈاف دس پر رکھاہے
اور دوسری بات یہ کہ سولرسےدس منٹ تک ایمپیراتےہیں پھرخودبخودبند ہوجاتےہیں جب دوبارہ کنکٹ کرتاہوپھرسےشروع ہوجاتےہیں یہ کیامسلہ ہےپلیز
@@faizurehman2464 Ap kisi achay multimeter ya volt meter se direct battery voltage check karain?, battery voltage meter per kia show ho rahay hain ?, aur agr koi aur dosri achi condition me battery hai tu wo replace kar ke daikhain.
کیا ہم پی وی سولر کے پورٹ پہ چارچر لگا سکتے ہیں،کیونکہ چارجر ایٹومیٹک نہیں ہے بیٹری کو اور چارج کر رہا ہے،
میں نے یہ ٹیسٹ نہیں کیا ہے ، ویسے کام کرنا چاہیئے۔ .Good Idea. Appriciated
Is controller ka subsay bada masla hai shayad ue masla tamam controller. Aj hota hoga masla.ye hai amp down kar deta hai agar 10 amp solar say aa rahay to 2 amp lost hojata controller mai koi aesa ctroller hai Jo amp ko.loss k bajaye increase karay
Asal me is controller ki copies buhat ban gaien hain, agar apko genuine controller milay ga tu us me aisa nahi hai.
Yahi controller lagaya he jo ap ka he Homeax CM 3024Z
Hlo bhaii
Hona shuru Hoti hy JB load off krta hn battery chargin bnd ho jati hy reason????
Ideally, aisa nahi hona chahiye, load ON ya OFF karne se battery ki charging ka koi tallauq nahi hai is device me, app connections verify karain, otherwise device change kar lain ,
Sir mera Solar wala side k Arrow ni a raha
Volt meter se solar panel ke voltage check karain, aue battery charing ya load ON per amp check karain , gar wo OK hain tu , No Problem. Sirf Display ka issue us se koi farq nahi parta.
Charging Wala erow ni chal Raha setting Bata den
Arrow na chalna masla nahi hai, masla charing hona ya na hona hai, multi meter se check karain, kabhi aisa bhi hota hai keh arrow show nahi ho raha hon, laikin device proper kaam kar rahi hoti hai
👍
السلام علیکم ورحمۃ اللہ وبرکاتہ اس میں جو اوپر ایک ہول بنا ہوا ہے جس میں ایک جیک بھی لگتا ہے اس کا کیا فنکشن ہے
Walaikum-as-Slam,
ap jis hole ki baat kar rahay hain wo is model me nahi hai ye baad ka model hai is me wo function built-in kar diya gaya hai.
Wo basically Temperature Sensor hota tha, wo puranay models me aata tha, jo ab alag se nahi lagta ab built- in hota hai.
Shukriya.
yar apna sra system kuo naidikya app nay bagarti ki ha ap nay way itni lambivedio bna k
How to factory reset it.
Default Settings are also included in this video. Kindly watch video carefully again.
Thank you.