I want to say thank you very much for the video ,one of the best info video I had found on this controller . The way you walked through each step of the wiring was perfect others should take notice and see how a wiring tutorial video is done . Great job
Hello, I have a question regarding tying the 2 power supply negative outputs together. I understand your point regarding not having a floating potential between them, but the GND and the COM- are electrically isolated (optical according to the manf) I checked it with an ohm meter and this is truly the case. So won’t connecting the PS negatives together defeat this isolation and leave room for some potential damage or other malfunction? Did you fully operate the controller like this without any problems. Thanks, and a great video, very informative as I’m assembling one now.
@@josephcoling8941 for the power supply line inputs the ground (earth) are tied to the same point and the neutrals and lines are fed from the same points, but not daisy chained. For the outputs I did not tie them together due to the opto isolation on the connection PCR. All works fine.
24:30 I am requesting some help, I saw you wire up a DDCS for CNC machine, for the End stops, could you let me know, where the other ends for the Yellow signal wire are hooked up to?
Thanks for the video. I was looking into building this machine but the shipping costs are quite high to ship to the United States. I was wondering if it would be cheaper to source all the materials locally. What are your thoughts?
@@IllDoItMyself Thanks a lot for your quick reply. But at this point i have a doubt. With the connections you are showing in the video you are feeding the controller board with both 24v and 36v at the same time. Is this ok ? Checking the controller guide they should be 24v both. Sorry but i'm not an expert in electricity 🙂
@@IllDoItMyself Hi Josh, I am also not sure about the 36v psu going to the controller? YuYong sent me two 24v psu's. One of them powers the controller and the other provides 24v for the I/O interfaces. They also sent me two 36v PSU's and they are used to power the stepper drivers. 36v on the controller I/O may work but not sure about that and 24v is the most common way to go when interfacing to relays etc for water pump or dust extraction.
A question for you, what stepper motor drivers are you using in the video? I am using TB6600's and cannot find one with ALARM positive or negative. I have followed your builds from the very first one, love your content!
hi John. I follow your videos on TH-cam and thank you for sharing them. I had a question about the ec300 controller. Is its wiring different from uc300? I want to use the ec300 controller for jobs that have very long G-codes. Is this controller suitable for bulky work or not? Sorry that my questions are long. Thank
@@coreybush2468 I talked to the company and they said the "Best is Offline DDCSV4.1 or MK4 mach3 controller" I still haven't decided but there are a lot of 3rd party controllers that are good. I think the mach3 is buggy if i remember correctly. I still haven't ordered.
Sure but that's not really playing into it any more than an android phone is also based on Linux. You do not require and Linux/Unix knowledge to use this.
HELLO GUYS. How to connect y axes. I have 2 motors there. If I use one driver for the both motor I will need a driver with " double " current. For example for nema 23 with 4.2 A I will need a driver that is used in big motors like nema 42. The price is about US$ 150 I watched some Russian videos. People there use synchronization board which allows to use one driver of every motor. And I see sync board looks like more reliable. It's US $ 36 but I can't buy from Russia. I don't know where to buy. Can you help. ANY IDEAS.
Концы кабелей драйверов моторов по оси Y, которые будут присоединяются к контроллеру, просто соедини как один каждого цвета и присоедини в соответствующие клеммы для оси Y. Дело сделано! В данном видео это так же показано;-)
Please do video regarding software also.... I am really waiting for ATC upgrading to this machine... I'll follow your guild lines and I'll repeat the same...
I want to say thank you very much for the video ,one of the best info video I had found on this controller . The way you walked through each step of the wiring was perfect others should take notice and see how a wiring tutorial video is done . Great job
Hello, I have a question regarding tying the 2 power supply negative outputs together. I understand your point regarding not having a floating potential between them, but the GND and the COM- are electrically isolated (optical according to the manf) I checked it with an ohm meter and this is truly the case. So won’t connecting the PS negatives together defeat this isolation and leave room for some potential damage or other malfunction? Did you fully operate the controller like this without any problems. Thanks, and a great video, very informative as I’m assembling one now.
What you end up doing I've come to the same conclusion, I am wiring one now
@@josephcoling8941 for the power supply line inputs the ground (earth) are tied to the same point and the neutrals and lines are fed from the same points, but not daisy chained. For the outputs I did not tie them together due to the opto isolation on the connection PCR. All works fine.
Très très propre, étape par étape, clair, nette et précis, vidéo formidable et très agréable a regarder.
Will you show how to configure and use dcss?
24:30 I am requesting some help, I saw you wire up a DDCS for CNC machine, for the End stops, could you let me know, where the other ends for the Yellow signal wire are hooked up to?
Would you please show the GRBL settings for $100, $101, and $102
Excellent video. What’s the name of the 3 and 5 terminal block you connected your power supplies to?
Why did you not earth out the braided shield?
Very good video. Very well explained. 👌
Excellent work but sir where to connect sensors to?
Hello, I wonder where you got the DDCS case. I'm interested to build mine the same way. I've got the DDCS Expert.
Thanks for the videos.
Thanks for the video. I was looking into building this machine but the shipping costs are quite high to ship to the United States. I was wondering if it would be cheaper to source all the materials locally. What are your thoughts?
Hi. To understand well, in your example the two power supply are both 24 volts ?
I'm running a 36 and a 24. Two 24s will work the same tho.
@@IllDoItMyself Thanks a lot for your quick reply. But at this point i have a doubt. With the connections you are showing in the video you are feeding the controller board with both 24v and 36v at the same time. Is this ok ? Checking the controller guide they should be 24v both. Sorry but i'm not an expert in electricity 🙂
Thats correct they both are connected to the controller. The controller takes power from the 24v pins. The other is used tor com+ and com-.
@@IllDoItMyself Hi Josh, I am also not sure about the 36v psu going to the controller? YuYong sent me two 24v psu's. One of them powers the controller and the other provides 24v for the I/O interfaces. They also sent me two 36v PSU's and they are used to power the stepper drivers. 36v on the controller I/O may work but not sure about that and 24v is the most common way to go when interfacing to relays etc for water pump or dust extraction.
A question for you, what stepper motor drivers are you using in the video? I am using TB6600's and cannot find one with ALARM positive or negative. I have followed your builds from the very first one, love your content!
What where you dip switch settings on the drivers ?
Hello. Can you please make a wire diagram?
Thanks
Здравствуйте, подскажите какая мощность блока питания и напряжение?
what size plug is require for this. 15amp or 10amp?
hi John. I follow your videos on TH-cam and thank you for sharing them. I had a question about the ec300 controller. Is its wiring different from uc300? I want to use the ec300 controller for jobs that have very long G-codes. Is this controller suitable for bulky work or not? Sorry that my questions are long. Thank
I'm very confused which controller to choose, can you give any advice?
Me too. What did you end up going with? The controller side of things confuses me, and I can't find a good resource to compare them.
@@coreybush2468 I talked to the company and they said the "Best is Offline DDCSV4.1 or MK4 mach3 controller" I still haven't decided but there are a lot of 3rd party controllers that are good. I think the mach3 is buggy if i remember correctly. I still haven't ordered.
What's advantages to this over uc 300 Mach 3 ?
This is an standalone controller so you don't need a Computer connected to it at all.
This controller is Linux based.
Sure but that's not really playing into it any more than an android phone is also based on Linux. You do not require and Linux/Unix knowledge to use this.
HELLO GUYS.
How to connect y axes. I have 2 motors there. If I use one driver for the both motor I will need a driver with " double " current. For example for nema 23 with 4.2 A I will need a driver that is used in big motors like nema 42. The price is about US$ 150
I watched some Russian videos.
People there use synchronization board which allows to use one driver of every motor.
And I see sync board looks like more reliable. It's US $ 36 but I can't buy from Russia. I don't know where to buy.
Can you help. ANY IDEAS.
Концы кабелей драйверов моторов по оси Y, которые будут присоединяются к контроллеру, просто соедини как один каждого цвета и присоедини в соответствующие клеммы для оси Y. Дело сделано! В данном видео это так же показано;-)
Please do video regarding software also.... I am really waiting for ATC upgrading to this machine... I'll follow your guild lines and I'll repeat the same...
Already a fail you cut off the shielding instead of terminating it
Could you make a TH-cam video like this?
Do you actually understand the way shielding works? Never heard of ground loops obviously?
Cnc panil wiring dajne
Whats the voltage/amp draw?