When I first started turning again 2 years ago a friend suggested I look up your channel for turning tips! He did not steer me wrong! I have learned many tricks and tips from you! I did some Turing as a teenager. I’m now 70 years old! Thanks again for all your help!
Thanks for this video, Sam; it touched on a number of points of interest. My original round nosed scraper, still a go to tool, was a Marples 1/2" HSS tool with 80 degree angle, bought around 1980, and I am quite comfortable with that. I made my 4mm x 20mm parting tool from purchased HSS bar, and cutting and grinding were quite a challenge (Al oxide wheel).It's a vicious tool! For rectangular tangs I hand groove two pieces of handle blank, before PVA glueing together and turning if necessary. When I started making handles I felt quite self conscious about using copper water pipe for ferrules, instead of purchased brass ones, but now prefer mine, as when clear varnished they stay smart and definitely wont split! Same with aluminium tubing. For internal Morse tapers I drill in steps, as you recommend, and then smooth under power with a round file. I've done that with wood, Nylon 6, and Plaster of Paris, which is finally hardened with shellac spray. A very sharp drill is necessary with nylon, to prevent grabbing. Bernard.
Bernard, yes I think shaping the wood for the rectangular tang is a good idea and then gluing the two bits of wood together. It is really a better procedure isn't it thanks SAM
Oddly enough, I just yesterday finished handling the new Robust Negative Rake scrapper I purchased from you. I used ash and a piece of copper pipe for the ferrule.
Two comments: you showed a square scraper/beading & parting tool, but it looked a lot like a bedan. A case of 'a rose by any other name' ? Re the rectangular tang in a round hole - have you considered adding half-round shims to pad out the hole and leave a rectangular opening? It's a little more work, but it makes for a more secure fixing.
An English bedan is trapezoid in section; like our traditional mortise chisels, to prevent deep binding. So I use one; it comes much cheaper, and in larger sizes. For rectangular tangs I channel two lengths of handle blank, PVA glue them together and then do the turning. Bernard.
Lignum vitae, a great wood for tool handles. A bit hard to come by and expensive but the handle will last forever. And it will look great. Great tip on purchasing some HSS and shaping your own tools. 👍👍 Another great video out the the Angelo shop. Thanks for sharing. Have a great day and stay safe. 🙂🙂
More great info Sam! I think I'd have to talk to myself pretty hard to make a handle from Bacote or Lignum Vitea since I save that for special turnings. They do make a beautiful handle that will last forever though. Thanks for another great informative video. Take care, Dave
Mike When I was scheduled to demo in Alaska in 2019-(cancelled because of Covid) The Alaska Woodturning Symposium. I had bought $300-400 worth of thread chasing wood. I was supposed to demo for 2 days and teach 5 days of hand's on classes. So I have LOTS of really nice wood- Sam
Dave, When I was scheduled to demo in Alaska in 2019-(cancelled because of Covid) The Alaska Woodturning Symposium. I had bought $300-400 worth of thread chasing wood. I was supposed to demo for 2 days and teach 5 days of hand's on classes. So I have LOTS of really nice wood- Sam
I make lots of my own tools also. I noticed your belt sander was a little noisy. I bought one similar to that and after some investigating found the motor bearings were PACKED with saw dust. Once I replaced them what a difference. so much quieter. Thanks for taking us through that process. Where do you get your tool steel blanks from? Amazon has some, but not always what I need.
I've started using hot melt glue for carving knife handles. These have to withstand a lot of force in many directions. I bet it would work well for turning tools. You don't have the mess of mixing epoxy or shelf life of other glues.
@@WYOMINGWOODTURNER I moved from hot melt glue, which is entirely satisfactory ,to PVA as it is neater and faster to do at the end of the day. Bernard.
Mike, I had to go back and look at this. I hope not too many people were watching at this point in the video. Did you see the note I left myself to move the clip. OMG I'm losing it. Oh well hope you didn't get the Covid too bad Sam
How did you remove the chisel shaft from the manufactured handle? Also, for a round shafted gouge, how many inches do you insert into the wood? I have two 1/2” bowl gouges insert 2” into my handle yet seems I get excessive chatter when using and curious if shaft depth could be the reason for the chatter; the handle is 16” long Walnut.
I clamped the steel in my metal vise and the handle just pulled off with a little twist. I am not sure is the chatter is coming from how the tool is embedded into the handle. Lots of things can cause this-dull tool- no bevel contact etc. Sam
Amazon link >>>>www.amazon.com/Square-Turning-Blanks-Rectangular-Cutter/dp/B09NRJRG7Z/ref=sr_1_6?crid=1A883JB4LHF78&keywords=12mm+HSS&qid=1659655385&sprefix=12mm+hss%2Caps%2C173&sr=8-6 Sam
I have seen several negative rake scrapers made out of old flat files at a few flea markets in my area. My question is, is that even safe to do or use? I put them back down as soon as I see what they're made from. Thanks for any insight!
One of a kind tools... you won't get them confused with someone else's tools !
Hi Sam, a big thank you from over here in the UK, I have learnt such a lot from you, your a good man Sam.
When I first started turning again 2 years ago a friend suggested I look up your channel for turning tips! He did not steer me wrong! I have learned many tricks and tips from you! I did some Turing as a teenager. I’m now 70 years old! Thanks again for all your help!
Thanks,
70 years old-you're just a kid!!!
😀
Excellent video. I enjoy the pace of your delivery and the details on how you make your handles.
Thanks for this video, Sam; it touched on a number of points of interest. My original round nosed scraper, still a go to tool, was a Marples 1/2" HSS tool with 80 degree angle, bought around 1980, and I am quite comfortable with that. I made my 4mm x 20mm parting tool from purchased HSS bar, and cutting and grinding were quite a challenge (Al oxide wheel).It's a vicious tool! For rectangular tangs I hand groove two pieces of handle blank, before PVA glueing together and turning if necessary. When I started making handles I felt quite self conscious about using copper water pipe for ferrules, instead of purchased brass ones, but now prefer mine, as when clear varnished they stay smart and definitely wont split! Same with aluminium tubing. For internal Morse tapers I drill in steps, as you recommend, and then smooth under power with a round file. I've done that with wood, Nylon 6, and Plaster of Paris, which is finally hardened with shellac spray. A very sharp drill is necessary with nylon, to prevent grabbing. Bernard.
Bernard, yes I think shaping the wood for the rectangular tang is a good idea and then gluing the two bits of wood together. It is really a better procedure isn't it thanks SAM
One of your original subscribers. Don’t say much but always watch ALL your videos
I can always spot the guitar....thanks Sam
Thank you Sam
Another great video! Thanks Sam.
You do great work and I have learned a lot by watching your videos.
Thanks. 👍👍
Great tips for making handles. Thanks
Always interesting, always informative, Thank you Sam!
Always helpful, thanks again Sam!
great work, Sam... as always
Good info to know. Thanks alot. Yall have a wonderful day.
I enjoy your videos. great way to save money on tools!
I need to get after this ... my beading & parting tool is worn down to a nub!
Good job.
I will never wood turn but I love learning about it.
Nice work Sam! Thanks for sharing! Take care and GOD BLESS 🙏!
Nice vid. As a 54 year old forced retiree due to health problems, I've made a few things and am always looking for tips to save money
Oddly enough, I just yesterday finished handling the new Robust Negative Rake scrapper I purchased from you. I used ash and a piece of copper pipe for the ferrule.
Great video Sam.
Just what I needed to see because I just bought a new Richard Finley skew chisel and it needs a handle.
Cool where did you find a Richard Finley SKew. Didn’t know they were available Sam
Nice tools. I got some of my father's knife making steel to make some but haven't done it yet.
Two comments: you showed a square scraper/beading & parting tool, but it looked a lot like a bedan. A case of 'a rose by any other name' ?
Re the rectangular tang in a round hole - have you considered adding half-round shims to pad out the hole and leave a rectangular opening? It's a little more work, but it makes for a more secure fixing.
An English bedan is trapezoid in section; like our traditional mortise chisels, to prevent deep binding. So I use one; it comes much cheaper, and in larger sizes. For rectangular tangs I channel two lengths of handle blank, PVA glue them together and then do the turning. Bernard.
Please read the comment from Bernard below he explains it very well. Sam
Well said. Sam
Lignum vitae, a great wood for tool handles. A bit hard to come by and expensive but the handle will last forever. And it will look great. Great tip on purchasing some HSS and shaping your own tools. 👍👍 Another great video out the the Angelo shop. Thanks for sharing. Have a great day and stay safe. 🙂🙂
Thanks, Sam
I too need to make a 3/8 or so square scraper.
More great info Sam! I think I'd have to talk to myself pretty hard to make a handle from Bacote or Lignum Vitea since I save that for special turnings. They do make a beautiful handle that will last forever though. Thanks for another great informative video.
Take care, Dave
I am with you on that, David. I guess I am just too frugal.
@@MikePeaceWoodturning Me too. Riotous living! Bernard.
Mike When I was scheduled to demo in Alaska in 2019-(cancelled because of Covid) The Alaska Woodturning Symposium. I had bought $300-400 worth of thread chasing wood. I was supposed to demo for 2 days and teach 5 days of hand's on classes. So I have LOTS of really nice wood- Sam
@@WYOMINGWOODTURNER Ah Ha! I understand Sam! Shoulda remembered that! Dave
Dave, When I was scheduled to demo in Alaska in 2019-(cancelled because of Covid) The Alaska Woodturning Symposium. I had bought $300-400 worth of thread chasing wood. I was supposed to demo for 2 days and teach 5 days of hand's on classes. So I have LOTS of really nice wood- Sam
Nice! I have made a couple of tools so far, and several tool handles. I enjoy your videos and appreciate your explanations.
I make lots of my own tools also. I noticed your belt sander was a little noisy. I bought one similar to that and after some investigating found the motor bearings were PACKED with saw dust. Once I replaced them what a difference. so much quieter. Thanks for taking us through that process. Where do you get your tool steel blanks from? Amazon has some, but not always what I need.
I've started using hot melt glue for carving knife handles. These have to withstand a lot of force in many directions. I bet it would work well for turning tools. You don't have the mess of mixing epoxy or shelf life of other glues.
Good idea I'll have to try it SAM
@@WYOMINGWOODTURNER I moved from hot melt glue, which is entirely satisfactory ,to PVA as it is neater and faster to do at the end of the day. Bernard.
33:50 Where do we move the clip, LOL? Caught Covid so am a bit fuzzy today.
sorry to hear that. best wishes for your recovery.
Mike, I had to go back and look at this. I hope not too many people were watching at this point in the video. Did you see the note I left myself to move the clip. OMG I'm losing it. Oh well hope you didn't get the Covid too bad Sam
@@WYOMINGWOODTURNER Pretty minor case. Still have an occasional cough. Yep we all miss something while editing.
Adoro, ver os seus vídeos, sempre bastante artísticos e educativos no que diz respeito a WoodTurning.
Thanks, Sam
How did you remove the chisel shaft from the manufactured handle? Also, for a round shafted gouge, how many inches do you insert into the wood? I have two 1/2” bowl gouges insert 2” into my handle yet seems I get excessive chatter when using and curious if shaft depth could be the reason for the chatter; the handle is 16” long Walnut.
I clamped the steel in my metal vise and the handle just pulled off with a little twist. I am not sure is the chatter is coming from how the tool is embedded into the handle. Lots of things can cause this-dull tool- no bevel contact etc.
Sam
Tools!
I have tried to make a couple handles and simple tools. Where did you get your 12mm sqrt HHS ?
Amazon link >>>>www.amazon.com/Square-Turning-Blanks-Rectangular-Cutter/dp/B09NRJRG7Z/ref=sr_1_6?crid=1A883JB4LHF78&keywords=12mm+HSS&qid=1659655385&sprefix=12mm+hss%2Caps%2C173&sr=8-6
Sam
I have seen several negative rake scrapers made out of old flat files at a few flea markets in my area. My question is, is that even safe to do or use? I put them back down as soon as I see what they're made from. Thanks for any insight!
Kevin, I used to use old files for scraping tools 30 years ago. I broke one or two!!!! Really not safe. High carbon steel.....but very brittle. Sam
@@WYOMINGWOODTURNER That's exactly what I was afraid of. I just put them back down on the table as soon as I see what they're made from.
Would it be better to not wax the handle so it has better grip and less tendency to rotate in your hand?
Bill, could be but I don't see a problem that it makes the handle slippery. Sam
Good video but you could have covered the subject in half the time. It was a bit gabby