Launch Tools, This information is very helpful, thanks! "please don’t charge the tablet when we are back up or restoring the data, and ensure the battery is not too low. Charging may affect communication". If I had not read it, I would have waited a very long time for the programmer to exit the Flash reading mode! When reading Flash, the programmer initiated a banner, "Wait, reading in progress" and hung! After watching your video report, I realized that this should not be so. I turned off the power and rebooted the diagnostics, turned on the Flash reading again and the reading was completed within five minutes!
I use this very often and it works very good for me I have no problem but one thing I could say whenever you are using this make sure you have your battery fully charged because if the battery go low The flash data going to stop reading it going to fail. So what I did is put it to charge for an hour when it got a charge it read and write the flash data in less than 5 minutes.
Have xprog3 for almost an year. In this time I messed up my audi a4 b8 immobiliser system because it device failed to read immo data (cost me £150 to fix it with ABRITES programmer). Wrote feedback but half year later still not fixed. Tried to read immo data on other few cars and ecu's on bench mode. Nothing. Doing step by step, trying to find videos but it fails all the time.
Привет Друг! Точно такая же ситуация! Купил устройство почти год назад, но до сих пор, не прочитал ни один ключ, от ряда автомобилей! Хотя сделал программирование MEG17.9.21 хорошо! Написал в поддержку на завод Launch, но до сих пор он не даёт объяснений!
Estoy leyendo una TCU de mercedes clase A me lee la eeprom la flash, pero luego no me carga la flash se me queda en 7 por ciento Y no carga....os aveis encontrado el porque?
Launch Tools, This information is very helpful, thanks! "please don’t charge the tablet when we are back up or restoring the data, and ensure the battery is not too low. Charging may affect communication". If I had not read it, I would have waited a very long time for the programmer to exit the Flash reading mode! When reading Flash, the programmer initiated a banner, "Wait, reading in progress" and hung! After watching your video report, I realized that this should not be so. I turned off the power and rebooted the diagnostics, turned on the Flash reading again and the reading was completed within five minutes!
I use this very often and it works very good for me I have no problem but one thing I could say whenever you are using this make sure you have your battery fully charged because if the battery go low The flash data going to stop reading it going to fail. So what I did is put it to charge for an hour when it got a charge it read and write the flash data in less than 5 minutes.
Where its delphi and continental ecm?
Does the current software version support Continental Simos 8.3
Have xprog3 for almost an year. In this time I messed up my audi a4 b8 immobiliser system because it device failed to read immo data (cost me £150 to fix it with ABRITES programmer). Wrote feedback but half year later still not fixed. Tried to read immo data on other few cars and ecu's on bench mode. Nothing. Doing step by step, trying to find videos but it fails all the time.
Привет Друг! Точно такая же ситуация! Купил устройство почти год назад, но до сих пор, не прочитал ни один ключ, от ряда автомобилей! Хотя сделал программирование MEG17.9.21 хорошо! Написал в поддержку на завод Launch, но до сих пор он не даёт объяснений!
Hope you make a video for SEIMENS ECU
Привет Друг! Твой девайс работает с какими ни будь ключами?
How can we got the software
Estoy leyendo una TCU de mercedes clase A me lee la eeprom la flash, pero luego no me carga la flash se me queda en 7 por ciento
Y no carga....os aveis encontrado el porque?
Creo que puedes volver a intentarlo
@@LaunchTools lo e intentado muchas veces y se queda siempre igual en el 7% y de hay no pasa
키등록을 위한 리뷰 정보가 너무 없습니다.
키등록을 위한 다양한 정보를 제공 해주시면 감사하겠습니다
Please asia car
Please the Asian car video
Launchpad 3