Hello, just a quick note of thanks for this video. I have a 2016 Z51 in Night Race Blue with factory silver painted wheels. I purchased the same 1/18 scale that you used for the video. Using your instructions I was easily able to paint the wheels to match perfectly. So now I have a lifesize Vette and a scale version that is a very close match! Thanks again good job on the video!
The door panels are easy to take off, get a small flat head screwdriver and wedge it carefully in the corners til it pops out. There are two metal dial pins typically on the door itself.
Do you have a video on how to loosen the Phillips screws on a 1:18 scale RC ERTL diecast model? I want to take the floor panel off so I can get to the interior and repaint the seats. Thank you!
u can remove the door panels by using a small flat head screwdriver and placing the head betwen the the edge of the door panels and the the door itself and and twist the screwdriver and pry in an upward direction and they'll come off
I have a 1:18 AUTOart Shark Grey C7 Z06 that i want to customize to make look like my dads. Yellow calipers, black stinger hood stripe and the black interior. But idk if i want to disassemble it
I have the same corvette but I turned it into a Michigan State police car. Broke the whold car bown. Replaced the wheels. Added a push bar and take down lights decals.
Incase you guys didn't know, this diecast channel is my secondary channel. My main channel is over real cars "Exoticars19" Please check it out if you have the chance! th-cam.com/channels/8laXTFwaibGFGIwbnxJ3Ww.html
Hey man, great video. I am trying to paint the white z51 wheels. I want it to match my dads car and am trying to paint the wheels silver (they come black). I was planning on using adhesion promoter then right to silver. Do I need to spray the wheels white first or just paint right over the black? Thanks.
I'm thinking I may do a build with my Corvette Stingray, what I'm thinking is I kinda build a widebody kit for it then get wheel spacers and pretty much customize it to where it looks like a C7R
Hi Friend....... i have some questions to ask you. i always have problem with the mirror when i take masking tape after i painted already and i removed the masking tape out the mirror look not clear. i don't know what is happen? can you have me ? what is the Mask tape you use?? sorry about my English. i hope you understand my question.
Ive been working on customizing my 1:18 maisto gallardo. I can't get the wheel to separate from the caliper and the axel, its a different setup than the stingray you featured. Any help would be appreciated thanks
That's sick to to that I have a couple of 1/18 cars I want to customize, but I dont want to mess them up. A couple of old schools and couple new schools all different companies.
I am literally working on one right now lol Its my old Diablo from the 90s that was all fucked up, just finished completely sanding it down to bare metal, deciding on what color to paint it. Already made a splitters for the front and sides, going to make a spoiler as well.
To buy this car off Amazon, click here: www.amazon.com/gp/product/B00KVNN04O/ref=as_li_qf_sp_asin_il_tl?ie=UTF8&tag=exoticars19co-20&camp=1789&creative=9325&linkCode=as2&creativeASIN=B00KVNN04O&linkId=e0491f771d68ff3c0709d540122364e4
Hello, just a quick note of thanks for this video. I have a 2016 Z51 in Night Race Blue with factory silver painted wheels. I purchased the same 1/18 scale that you used for the video. Using your instructions I was easily able to paint the wheels to match perfectly. So now I have a lifesize Vette and a scale version that is a very close match! Thanks again good job on the video!
The door panels are easy to take off, get a small flat head screwdriver and wedge it carefully in the corners til it pops out. There are two metal dial pins typically on the door itself.
i love the customized car model video! looking forward to more!
Do you have a video on how to loosen the Phillips screws on a 1:18 scale RC ERTL diecast model? I want to take the floor panel off so I can get to the interior and repaint the seats. Thank you!
Awesome car! Goods review as well! another supporter here!
i just watched the whole video and i gotta say it looks good!
u can remove the door panels by using a small flat head screwdriver and placing the head betwen the the edge of the door panels and the the door itself and and twist the screwdriver and pry in an upward direction and they'll come off
I have a 1:18 AUTOart Shark Grey C7 Z06 that i want to customize to make look like my dads. Yellow calipers, black stinger hood stripe and the black interior. But idk if i want to disassemble it
I have the same corvette but I turned it into a Michigan State police car. Broke the whold car bown. Replaced the wheels. Added a push bar and take down lights decals.
Incase you guys didn't know, this diecast channel is my secondary channel. My main channel is over real cars "Exoticars19" Please check it out if you have the chance! th-cam.com/channels/8laXTFwaibGFGIwbnxJ3Ww.html
Exotic Diecast why didn't you paint the heads up display gloss black on the corvette?
What brand is the black paint that you used for the blue Corvette stingray
The taping and pulling apart the car, pretty good, but the kind of paint you could get better for a couple of dollars more
Did you just covered the corvette letter on the calipers?
Can I use airbrush paint to paint this cars?
Is there a tutorial on how you painted the interior?
CAN YOU HEKP ME ABOUT THE REMOVE 1:18 WELLY WHEELS???
Give them a pull
you can remove the door panels by popping it from the inside where the hinge is
Hi, do you think it would be possible to customize this car into a closed convertible top.
Could you get a run of the mill 1:18 scale RC car and make it fit under the nice metal models?
Hey man, great video. I am trying to paint the white z51 wheels. I want it to match my dads car and am trying to paint the wheels silver (they come black). I was planning on using adhesion promoter then right to silver. Do I need to spray the wheels white first or just paint right over the black? Thanks.
I have a maisto 69 charger I want to do a wheel swap is it possible to use gmp wheels?
Will need glued in place... Unless you can find some hubs to make the wheels rotate
I'm thinking I may do a build with my Corvette Stingray, what I'm thinking is I kinda build a widebody kit for it then get wheel spacers and pretty much customize it to where it looks like a C7R
i want to detail my maisto mercedes clk LM i cant seem to take it apart.. theres this portion thats stuck and i cant figure out.
Didn't require dismantling. But the end result was very good.
do u have a 2004 miniature model of a corvette for sale?
I’m having trouble removing the wheels. How difficult is it to put on aftermarket wheels?
Hi Friend....... i have some questions to ask you.
i always have problem with the mirror when i take masking tape after i painted already and i removed the masking tape out the mirror look not clear. i don't know what is happen?
can you have me ? what is the Mask tape you use??
sorry about my English. i hope you understand my question.
I have a question, in what kind of case, paint remove and/or primer is needed
Cool
you should paint the mirrors black on the 458
Ive been working on customizing my 1:18 maisto gallardo. I can't get the wheel to separate from the caliper and the axel, its a different setup than the stingray you featured. Any help would be appreciated
thanks
TheDiecastMan lol hi Diecast man I watch ur vids they r awsome
Well done, thanks
Hey! can you get the GTAuto Pagani Huayra?
why dont you pinstripe the wheels
More video's like this!
Hello great content btw! Following for a while and do you take requests?
That's sick to to that I have a couple of 1/18 cars I want to customize, but I dont want to mess them up. A couple of old schools and couple new schools all different companies.
were do you get the model cars from
You can get them at Sam's club and Costco
How did he paint the interior in black?
With a brush...
Can I have a request that can you customize a Ferrari Enzo paint it in black rims?
Quick question: what do you think of the motormax mclaren p1 1/24? Is it a good model for the price?
stay away from it man
meme man stay away from motorman they are very low quality pick burago make to or well for budget cars
what model is the huracan??
Bburago. www.amazon.com/gp/product/B00JHJFBFO/ref=as_li_qf_sp_asin_il_tl?ie=UTF8&tag=exoticars19co-20&camp=1789&creative=9325&linkCode=as2&creativeASIN=B00JHJFBFO&linkId=c79953ee579d6fe52bdd0f2d9b8a0902
thank you😀
Can you customise a Porsche gt3 rs please
really cool video thanks
get an autoart mclaren p1
customize a Lamborghini pls!
I am literally working on one right now lol Its my old Diablo from the 90s that was all fucked up, just finished completely sanding it down to bare metal, deciding on what color to paint it. Already made a splitters for the front and sides, going to make a spoiler as well.
Great videos... but you could do with better lighting 🤔
I have this same car
We’re did u buy it pls tell me what site
You could’ve did the a black interior with blue seats. I mean it your customizations but I’d like to see a bit more creativity on your behalf.
Its so hard taking those wheels of my fingers hurt
I’m having a hard time removing the wheels as well. Feels like I’m gonna brake the plastic.
Y don't u have any Camaros
I have a 1969 Camaro
Maisto Camaro SS 2016 wheel removal please
서민수 same problem bro I have the exact same diecast
The door panels do come off, you just gently pry it off
With better paint, your lines will come out cleaner
Laguna blue tintcoat
how much is it
awesome
plzz more costumize videos!!!
Youre dad has the real car. And you couldn't afford a a high grade model over 100…😂....
Sagatbalrog don't be rude
To buy this car off Amazon, click here: www.amazon.com/gp/product/B00KVNN04O/ref=as_li_qf_sp_asin_il_tl?ie=UTF8&tag=exoticars19co-20&camp=1789&creative=9325&linkCode=as2&creativeASIN=B00KVNN04O&linkId=e0491f771d68ff3c0709d540122364e4
Exotic Diecast