CAT 950H SHOVEL LOW POWER AND KNOCKING SOUND

this video, is for for extra idea for everyone who do not know where to and give solution for this type of problem.

[@jessonsalas3513]

Good job master...

[@sangeetmanch1797]

sir , how to caterpillar et please make the one video

[@ahmedovo3011]

well done

[@mahadiking3324]

Good job brother

[@caterpillarjhunhunk]

thanks bro

[@illuminadosanantoniojr.3022]

Sir tnx for sharing

[@caterpillarjhunhunk]

welcome

[@jhayarlisondra300]

Sir gd morning ung cat 950H nmin,after kinabit ang injection pump,umandar nman kaso kng may load mahina ang power nya..

[@adilbaigslaveofallah373]

Good morning sir

[@caterpillarjhunhunk]

yes sir this my whatsapp [phone]

[@escabaldemueln.8219]

Pashout chief

[@caterpillarjhunhunk]

sige wait mo lang s next video ko

[@romerl.4297]

Sir while you were doing cylinder cut out procedure, I was also looking at their delivered fuel volume. Aren't they too high reaching 50+? Just replacing

[@caterpillarjhunhunk]

fuel pressure depending on the pump output pressure they must be reach the minimum pressure or else the is hard starting, sometime not possible to start, if you think that the pressure shows on my video, the system they have a program that they automatical trim the pressure depend on the trimp program setup by the caterpillar.

[@sivakrishnabandaru9404]

How to check transmission oil pressure and to improve the pressure.

[@caterpillarjhunhunk]

Every machine have the testing port or plug to check the pressure

[@caterpillarjhunhunk]

Check the gear pump pressure, make it sure that the pressure is in normal, before you are going to proceed at solenoid valve gear selector

[@MitzvosGolem1]

Is that CAT ET or a dealer level computer scanner?
Excellent work Akhi.
Salaaam

[@caterpillarjhunhunk]

CAT ET bro

[@MitzvosGolem1]

@@caterpillarjhunhunk CAT ET is limited cannot clear DPF codes here. I am buying one .
I have a " Candoo" cheap one does basic scans on CAt ,Cummins Volvo.

[@caterpillarjhunhunk]

@@MitzvosGolem1 actualy bro i am using CAT ET we got it from cat dealer

[@illuminadosanantoniojr.3022]

Sir if I need your help would you do thank you sir

[@caterpillarjhunhunk]

your very welcome sir whats app [phone]

[@byahesanz3001]

Sir 950H caterpilar arm not going down

[@caterpillarjhunhunk]

bro try to check the solenoid at the control valve, or you can try actual test of lever control to exchange arm control to bucket control, if the arm control are working to bucket it means solenoid damage or wiring harnes

[@imran3055]

Sir catterpillar c9 engine did not take throttle.. only run idle rpm (800) we check engine display.. error (840, or 802) show... then i check the detail of this error is (input incorrect).. please tell me the what's the problem???

[@caterpillarjhunhunk]

this engine what type of machine used

[@imran3055]

Its power pack pennine.. which use on stone columns

[@caterpillarjhunhunk]

@@imran3055 can you send me the pic of monitor and some details in my whatsapp [phone]

[@imran3055]

@@caterpillarjhunhunk ok

[@jermiepadilla4872]

Hi sir I ask you about low power problem caterpillar wheel loader 950 I can you help me sir thank you

[@caterpillarjhunhunk]

can you pls give the details of the exact problem or contac me in my whatsapp[phone]

[@amircakic740]

Can you help me… we start engine normal. After 30sec motor temp goes to max power drop and machine loss energy …. And goes off …. And again, again the same…. Maybe wiers,procesor what ?

[@gelordtv2719]

Ano facebook page nyo sir?

[@roelcurangcurang897]

Broo may email add ka,pwde ba kita macontact slmat

[@caterpillarjhunhunk]

yea sir [e-mail]
whatsapp [phone]