How to program a Linear Remote PLUS Garage Door Opener Troubleshooting !
ฝัง
- เผยแพร่เมื่อ 11 ก.ย. 2024
- Replacement remote→ amzn.to/2dQUtdz
Safety Sensors→ amzn.to/2dCYoYJ
If the light does not light up on your remote. Replace the battery. You will also notice that there are 3 buttons on the remote. Each button sends out a specific signal and can not be changed. So it is possible if you have two or more openers to program all of them to one button. If you did that all your garage doors would open with the push of one button. I doubt you would want that. So the great thing about the remotes with more than one button is you can open up multiple doors or even use it to turn on your garden lights or things like that.
I included some info at the end on what the flashing codes mean on the main unit. Most repairs to garage doors can be done by the homeowner and are easier than you may think.
SUBSCRIBE→ www.youtube.co...
For those who offer to buy me a drink, thank you! I have Venmo and CashApp.
Venmo: AdamCash
CashApp: $AdamDIY
Business Inquiries: please email me from the About page:
/ adamdiy
Disclaimer:
This video is only for entertainment purposes. Any injury, damage, or loss that may result from improper use of tools, equipment, or from the information in this video is the sole responsibility of the viewer and is to be used at the discretion of the end user/viewer and not AdamDIY and or Adam Hill. If you are uncertain about any step of the process, or feel unsure about your skill level, seek a more authoritative source.
visting my elderly mom, she thought it was her remote batteries...your video saved me over $200 and without your video, i wouldng have know what to do to fix this. your going through the flashing of the lights, i never would have been able to read them, and you made it possible to show me it was the vacation switch! thank you so much!
I was to spend a lot, but after your post I was able to fix. Awesome. Thank you Adam for saving my money.
5 flashes was killing me. Didnt realize it was an easy switch on the wall. Thanks!!
I tried to use a Genie remote and a Chamberlain universal remote. Both would not work properly. I had to use a Linear remote to finally get it to program. Not Lowe's and Home Depot do not sell Linear remotes. What a journey.
Great tutorial Adam. Thank you.
Thank you for this video. You helped me figure out vacation mode (4 blinks) which is why my new clicker wouldn't program. I pushed the wall switch up as you instructed and the clicker then programmed on the first try.
Thank you for this. I just programmed my remote I bought off Amazon in a matter of 10 seconds. Amazing.
This was super helpful! Thank you!
We had the exact model, we had a power outage, and something is off. The clickers are only working in a close range, like 2 feet. I changed the batteries in them and reconnected them with the unit. Any suggestion what's wrong? I even changed the light bulb, and it's the one that doesn't interfere with the range. I played around with the antenna as well... nothing change. Any suggestion??
I’ve got the same lift motors as in your video. Have you ever had a motor go out? My door raises and closes with just a finger. With the door detached from the drive chain, the motor has trouble running just the chain. Can the motor be lubricated? The unit is a little over 2 years old. Any help would be greatly appreciated. Thank you.
Easy fixed....thanks man
Thanks
I wonder if you could help , we think the torque spring needs to be adjusted tighter . The garage door opens a little less than half way . This happened after a power outage , when the power came back on ; to open the garage door you have to keep pressing the remote two or three times before it opens all the way . Any suggestions ? Would you recommend tightening the torque spring ? To give more tension ?
can you make a video of the opener running? I'm just curious on how it runs
Hi Adam,
I have the same opener, what is that model ? I can't find the model label on mine.
Is this a LDC0800?
I've tried everything and cannot program the keypad and remote. Either one or the other will work. Can you help me? Thanks Denise
The red light on the main box (the one on the ceiling) has the red light flashing but it is a bit faded... continuously...
Adam I have changes my batteries in remotes and tried to program remotes. My opener learn buttom stays red all the time. What does this mean?
Hi
I have a question. The green led light on the linear keypad for one of my garage door opener is shows opposite. The door is closed the green led light shows is lit on the top. Is there a way to fix it. Also I bought an MyQ Chamberlain WiFi garage hub and I am trying to pair it to the 2 car garage door. For some reason both the garage door gets synced and it’s not working as expected. Any thoughts on that ?? Appreciate your response. Thank you!!
why would the trolley back up two inches after opening
Where do you find the ID to use a remote attached to the outside of garage
My linear LD033 the clicker has to be within 3 feet of the opener for it to work, the learning light is always on, kinda flickering but always on. wall panel works. reprogrammed the opener, changed battery, clicker works on another door. erased memory and reprogrammed it, unplugged the opener and non worked, any tips
The learn button turns on every time I use the remote but the door never opened.
Hi, I have question & it looks like you have the answer on how I can pair this linear garage with a Mercedes Benz Homelink?
Open and close wall mount works fine....I can also open door with remote, however it will not close using remote. I noticed one of the sensors wasn't lit. Noticed the wire was cut, so I spliced together...still no power on the sensor. Next step is for me to check power...what volts Should I look for on sensors?...thank you.
Have the same problem, did you get it figured out boss?
I have a problem with my garage door opener going down and reversing. It seems as if it is trying to close more than is allowed. How do I adjust this?
Hello. My learn button light remains on. No matter what. Any suggestions. Thanks
Is there a way to adjust or reset the light timer? It used to stay on for about 5 minutes after opening or closing, then suddenly dropped to 10 seconds. How can I get it back to 5 minutes? Thanks.
What is the problem if, when I click the button on the remote to send a signal to the opener, nothing happens? The light flashes on the remote, but the opener doesn’t register that it’s been programmed.
When trying to program 2 more remotes it does not work
I bought the one-button remote off Amazon-says it's compatible with my LDCO800. All the lights do what they do on this video, but it doesn't open or close the door. The red light comes on the opener when I press the button on the remote-so it's getting the signal, but nothing happens. Can anyone help?
What is wrong if the door will only open half way up and will not open by the remote at all
I have a LD033, how do I delete the current keypad code and then program a new 4 digit code? Thx
excellent very easy too program and use thanks sew much
What if your learn button doesnt stay on for you to program it?
Should've went with a Highlift Package.
you didn't say at all how to trouble shoot #7. all you did was read it....
Mine doesn’t have lights on the remote though
I did it the same as you connected but I try to open it and it did work and I try to closed it did not work
Flashes 4:43
Garage door is receiving the signal with my remote but it isn't opening help?
@Adamdiy Can a control be deprogrammed ? If yes then how? Our neighbors garage is opening with our control :\
+FABIOLA JIMENEZ The neighbor needs to clear the codes off their opener and then retrain it to only their remotes. There is nothing you can do, they need to do it.
+AdamDIY Thank you!
Can't they just reprogram their opener with a new code? Instead of bothering the neighbor?
My garage door opener reads that it’s trying to learn but it doesn’t open
I have a solid red light on the back of this door opener , so the remotes will not work
Mine won’t program for some reason
Key pad works but remote will not
The door opens by the remote but will not close
Any ideas
Como traduzir brasileiro
Queria importar
My garage door won't open all the way. It comes up little bit and than stays there. Need help!
+nakia bellamy I have two videos that may help for that. Let me know what you find. th-cam.com/video/FTzA7oXy8fM/w-d-xo.html and then if you dont find your problem watch this one th-cam.com/video/uSyI-zbpxEc/w-d-xo.html
Wall station is not the sensors. The wall station is the buttons on the wall used to open the garage. Usually by the entry door. This video shows you should not be giving advice yet.
Hi
I have a question. The green led light on the linear keypad for one of my garage door opener is shows opposite. The door is closed the green led light shows is lit on the top. Is there a way to fix it. Also I bought an MyQ Chamberlain WiFi garage hub and I am trying to pair it to the 2 car garage door. For some reason both the garage door gets synced and it’s not working as expected. Any thoughts on that ?? Appreciate your response. Thank you!!
One more thing your sensors/photo eyes should be between 4 and 6 inches from the ground.