Heim Motorcycle Swivel Trailer Hitch
ฝัง
- เผยแพร่เมื่อ 15 ก.ย. 2024
- Today we install the heim motorcycle towing system on our 2004 harley ultra and 2000 kwick kamp mototcycle camper
Mcstache Merch; mr-mcstache.cr...
Visit our sponsors
slacksquatch beard products; www.etsy.com/s....
Mail;
Mr. McStache, P .O.Box 25 Lockborne, Oh 43137
facebook;
Motorcycles;
2003 Harley Ultra Anniversary edition w/Frankienstien Trike
2004 Harley Electra Glide Ultra
2015 Harley electra Glide Limited
Equipment used to record our videos;
Insta 360 x3, Insta 360 RS, Sena 20, iphone 13
#armyveteran, #ohiobiker, #livingwithptsd, #handlebarmustache, #vet, #harleydavidson,
#motovlog #ohiomotorsports #supportmvc #thewayofthe_stache #motorcamping #kwickkamp
Hello Mr. McStache. I guess I use the Torque wrench correct. Yes wheel chuck must be removed. Thank you for sharing this with us. 💕NonnaGrace 🐓
I your that good I need to have you as a guest on my next install lol
Nice, liking all the movement you get.
I do t know if I have the nerve to try it but I bet I could scrape the floorboards and still be good!
@@Mr.McStache It Looks like it should. I am with you about trying out the range.
🧐Think if you need to attach trailer to bike in mornings,would need extra cup of Coffee to line up holes .. Neat Setup👍💯
I need an extra cup to get outa bed, wife will be hooking up the trailer 😂
They are a good addition for trailered bikes...
Everyone says that’s the best one
I know you and I talked about a few styles of hitches. I think this will be a good way to keep stress off the bike.
Well you know, it will help if I happen to drop the bike lol
Sweet...Kake needs this for Bubbles.
It was an easy change. USA trailer only wanted 200
Thanks for your video. I just purchased a used trailer and was looking at hitch options. This was a great help.
I was hesitant at 1st. Though it was a little pricey but after installing it, well worth it. Removes the slack at takeoff and stop. Also tracks a lot better
That's a pretty trick little part. Even if the bike were to have a parking lot tip over the trailer would be protected. At a minimum it may stop the frame from being twisted. Great video.
That’s probably why the wife made me get it, in case I drop the bike lol happens more than I care to admit.
Nice! I’ve seen swivel ball hitched but never one of those. Pretty cool!
Wife wanted the best there was and this is what kept showing up. With the dual pivot points it should do it all
👍 well this system 👍
Good system
Not only is there the rotational benefit on turning you spoke of when the bike is leaning. But there is no instantaneous shift or tug, fore or aft, on acceleration and decelerations. Absolute sublime pulling connection. Bushtec trailers set the bar with their renowned Heim connection. Beautiful motorcycle. I am into lights. And lots of them. See and be seen. Safe and happy travels. ATGATT.
As a rider it pulls and tracks a lot better. Definitely worth the money
Good call installing it,, Jason. I've seen videos of bikes getting laid down intentionally to show the difference, game changer. Hmmm, that was your left ear? Next time Doyle is talking trash about ya, I'll have to make sure to remind him to stand to your left, so y'all don't have to hear his BS. Hahahaha. Ride safe.
Mississippi torque wrench? That’s a new one. I usually refer to those as the “nut rounder-offer” or “adjustable hammer”. LOL.
Nut rounder offer I will agree with hammer is improper use. If you are going to pound that the time and get the BFH and beat it to submission lol
Thats a cool setup. I was scared of how much the bike moved when you attached the trailer the first time.
The Harley has kickstand with a ton of play, it’s actually (originally) designed to be able to “shake and wiggle” the bike onto a concrete block and be able to change the rear tire. The original design is Harley was with long ride in mind. Part of why I believe they have not gone to led lights. The lights they run can be bought at almost any gas station
LOL I do that every day, you know where did that go? Cresent hammers/prybars/fitall
I know it’s here somewhere….
Heim joints are good, been used for decades on race machines etc, only one possible issue is if your going to tow another trailer, helping a buddy, your stuffed, same goes if your bikes damaged or broken down, trailer needs to be towed by the corresponding hitch. I’d go def for a swivel conventional tow hitch...
Nice vid though 😃
I have been picked up on the side of the road before. I carried the old trailer nose then now I carry an extra pin. Could also remove mine and use it or put the ball back on for other trailer. But the “slop” is gone and trailer tracks a ton better. Thanks for your input, great things most don’t think about
Nice . But if I was you would keep the ball recever in camper just in case need to pull it with regular ball hitch
That’s a good idea or carry my Mississippi torque wrench so I can put that ball replacement on somebody else’s bumper
@@Mr.McStache shaft size be different . But either way
👍👍💯 that should do a good job. Great video catch you later brother.
I was going to test ride it down to you but now the tolls will be double because I have a trailer. Can’t afford that
@@Mr.McStache 🤣🤣👍 yeah I hear you.
Crescent Hammer
You didn’t like Mississippi torque wrench?😂
😎👍👍
Thanks for watching
🤘🏾👍🏾
Thanks for watching
Cool....What was in inside dimension of your trailer tongue?
inside dimension of 1-3/4" x 1-3/4". The swivel bolt mounting holes should be 2-1/4" apart in the tongue. This is what it called for in the order form and what mine was. Have a feeling its a common measurement. Trailer tracks so much better too!
I have the same hitch and with it, your trailer is not as likely to be stolen as a ball hitch would be.
I didn’t think of that bonus, thanks for sharing
Doyle is going to sue you for infringing on his dickin around in the shed lol
Only if you tell him what infringement is lol. I did not touch anything he worked on
Just do yourself a big favor and don’t forget the red Loctite on your pin bolt……. (I noticed you did not) Otherwise, you and your trailer will part company. Take it for me, that big nut will not stay tight, and when it comes loose, will give you every kind of havoc you can think of and your helmet will become absolutely essential one more time believe me, you don’t want to see that happen.
Yes most of my installation videos I say but don’t always show it due to videoing. I will normally pull it all apart and do it with no distractions to ensure a complete Job. Thanks for checking I appreciate it