I am happy to hear that you appreciate the videos and hope that they can help even just few people out. I made this one after a personal friend told me that he did not change is over do tire because he thought is was to difficult without some special factory tool. He was surprised to hear that the hub comes apart. He had no problem after i explained the process.
When replacing the inner tube, sprinkle a little talc powder inside the tire and use a paper towel to spread/coat the inside of the tire. Dust a little on the inner tube and rub a light coat over the whole inner tube. Slipping the tube into the tire will be easier, and when inflating the tire the tube won't get twisted in the tire. Add a little air first, bounce the tire, deflate and then pump up to final pressure. Same as you would when repairing bicycle inner tube.
OMG!!! Wish I would have seen this about how to get the rear sprocket straight because I didn't even think about it. I thought something was wrong because it was a little loud after a tire and tube replacement but I also replaced the chain tensioner spring so I thought it was just that. Ended up grinding the teeth off the front motor sprocket and costing me $110 to replace the rear and front sprockets, chain, and the chain tensioner 😭 but I get my parts tomorrow 😉can't wait to ride again. I LOVE MY GOPED ESR1000H
PLEASE HELP.. My bearings on my OEM gsr40 mag wheel are loose! like i can take the bearings in and out with my finger... why did this happen? i know it's not a problem once the axle is all tight with the spacers, but i'm confused.
So I took off the front caliper on my new trail ripper thinking I need to do that to install tire, it seems the tire is rubbing on the break caliper now not sure how to fix
noticed the 4 wheel nuts on my gtr are hard to remove, they dont loosen up all the way. it only loosen up when the nut is almost completley off the bolt. is that normal?
Huh?…..You need to first let all the air out of the tire, then remove the 4 bolts that hold the rim halves together so they can be pulled apart. The tire's bead on the rim may have a tight grip on the rim and may be keeping them together so get the wheel wet, lay the wheel flat on the ground as you step on the side wall of the just the tire to break the bead.
How to tune a wheel? Tuning an engine should be left to the experts. I have seen a lot of good engines go bad from people thinking they can do there own engine tuning. There are a lot of little things one should understand that a video just would help with. It's like watching open heart surgery. You can see how to do it but without the proper medical knowledge and training your in for big trouble if you try it yourself.
I am happy to hear that you appreciate the videos and hope that they can help even just few people out. I made this one after a personal friend told me that he did not change is over do tire because he thought is was to difficult without some special factory tool. He was surprised to hear that the hub comes apart. He had no problem after i explained the process.
When replacing the inner tube, sprinkle a little talc powder inside the tire and use a paper towel to spread/coat the inside of the tire. Dust a little on the inner tube and rub a light coat over the whole inner tube. Slipping the tube into the tire will be easier, and when inflating the tire the tube won't get twisted in the tire. Add a little air first, bounce the tire, deflate and then pump up to final pressure. Same as you would when repairing bicycle inner tube.
thank you
Glad to be part of the goped generation 🙌
OMG!!! Wish I would have seen this about how to get the rear sprocket straight because I didn't even think about it. I thought something was wrong because it was a little loud after a tire and tube replacement but I also replaced the chain tensioner spring so I thought it was just that. Ended up grinding the teeth off the front motor sprocket and costing me $110 to replace the rear and front sprockets, chain, and the chain tensioner 😭 but I get my parts tomorrow 😉can't wait to ride again. I LOVE MY GOPED ESR1000H
Still AWESOME to this day and I'm sure they're still helping people!
Yup, just picked up a used Bigfoot and need to swap the tires out.
Did you make a video of how to remove the back sprocket?
@DavisRacing38R it's the rear wheel for a GoPed "GSR Cruiser" model. GoPed.com has them in stock.
Do you know how to get the bearing off?
PLEASE HELP.. My bearings on my OEM gsr40 mag wheel are loose! like i can take the bearings in and out with my finger... why did this happen? i know it's not a problem once the axle is all tight with the spacers, but i'm confused.
So I took off the front caliper on my new trail ripper thinking I need to do that to install tire, it seems the tire is rubbing on the break caliper now not sure how to fix
noticed the 4 wheel nuts on my gtr are hard to remove, they dont loosen up all the way. it only loosen up when the nut is almost completley off the bolt. is that normal?
What part number for each parts
Hey! Can you tell me wheels and tires those are? & Sprocket! Thank you very much~
my bigfoot back tire rims dont come loose. i will try and try to loosen the bolts to take of the tire but it doesnt even move a little. please help
You can get all original GoPed parts from GoPed.com
GoPed Ltd. the bearing's how to you replace thoses mine are bad bad wheel locked up? thanks
@@sharksg1401 hey I'm Daniel and I live in west Sydney I am a goped mechanic if you need anything call 0415269171
Danz that man
Huh?…..You need to first let all the air out of the tire, then remove the 4 bolts that hold the rim halves together so they can be pulled apart. The tire's bead on the rim may have a tight grip on the rim and may be keeping them together so get the wheel wet, lay the wheel flat on the ground as you step on the side wall of the just the tire to break the bead.
How to tune a wheel? Tuning an engine should be left to the experts. I have seen a lot of good engines go bad from people thinking they can do there own engine tuning. There are a lot of little things one should understand that a video just would help with. It's like watching open heart surgery. You can see how to do it but without the proper medical knowledge and training your in for big trouble if you try it yourself.