…. Народ не устаёт придумывать разные варианты станков, только бы не покупать заводские… Правда, экономия , при этом, очень солидная … 😊Удачи и творческих успехов ! …
It works well, looks very practical, and does what has been intended for hobbyists, however besides some minor modifications on the chuck, the railing, and perhaps a safety shield in front of the workstation are doing an awesome job.
Человек не имеет даже малейшего представления о работе на токарном станке. Если этот станок лучший, и он доволен результатом, то трудно представить какие были первые.
Idia intelegent Verry good,👍👍👍👍👍🇲🇦🇲🇦🇲🇦🇲🇦 فكرة رائعة أتمنى لك التوفيق من المغرب 🇲🇦🇲🇦🇲🇦👍👍👍👍👍 اشغلنك إݣا وين المليح أفدا يرضو ربي👍👍👍🇲🇦🇲🇦🇲🇦🇲🇦🌹🌹🌹🌹🌹 Une bonne idée intelegent homme je souhaite une bonne avenir au futur👍👍👍🇲🇦🇲🇦🇲🇦🇲🇦🌹🌹🌹🌹🙏🙏🙏🎩🎩🎩
Big thank you, I have a motor in a washing machine that I will extract out & I want a lathe for metal & wood, let start with wood! 13:09 Please, where is the video link with many wiring diagrams? I can't find it.
Yeah, I'd be a bit leery of using that as a direct-drive unit Not too keen on nuts & bolts, with shards of angle iron, being flung at me at17K rpm (I'm guessing the rpm) You could add some nail spikes around the perimeter of that faceplate to increase it's aesthetic appeal, I guess
These motors from washing machines usually run at 1200 to 2300rpm. Wooden chucks if made from birch plywood and angle iron are a good and safe method. Particle board is never a good idea, even when it is covered with melamine. The only structural problem I see is in the tailstock - a triangle is needed to stiffen up the construction.
I have a really nice Bosch washing machine motor that I pulled and it is seriously fast. But it doesn't have the same torque yours does. What are the specs on it and where did you find it?
Нормальная конструкция! Для обеспечения ТБ нужно установить защитный кожух, что элементарно сделать для данного патрона, причём даже навскидку есть как минимум три варианта.
Excelente diseño Amigo , Muy Buen Trabajo , permíteme copiarlo , además me has dado idea para un torno para bujes de bronce o aluminio . FELIZ NAVIDAD Gracias , Gaspar
Para hornear madera se utiliza la uña que entra fácil en la madera más rápido y seguro, aproximadamente este plato es más metal y este no aguantaría ni el peso ni la presión de corte.
Might be good for smaller objects like the dowel for an upright paper towel holder (or actual dowels). But your not going to be turning out any bowls of significant size (pun intended). On that point it leaves a lot to be desired. But then again so do model rockets, RC aircraft/boats/cars, and drones.😏
Great video. But it seems a bit unsafe. Wood used for tools of this sort can go 'crack', and hit you in the face. A lathe should have metal and steel components only.
Hola esta buena la idea pero le faltaria una caja de seguridad o tope para tapar los ángulos y tornillos al girar por asi cómo está es un peligro . Pero muy buena idea 🇦🇷
At 15.20. You are starting the Motor with your hands. So obviously you haven`t got a capacitor connected,which also means that the secondary winding is not connected.
Very nice point made. The winding can be done carefully so that it can be self start and also if more copper is filled into the slots, then it can be made into heavy duty motor. If I were to design this motor, I would make it in chain winding configuration which can even save more energy and almost never heats up on long duration of operation.
Liked the clip. A little long. The chuck might be put on a hand drill. There are a lot of other clips about how to use a hand drill to make a lathe. So the newer chuck might be an upgrade?
Great idea , BUT I was cringing when you put your hand next those brackets as they are spinning to sand that piece. Ok it would have been soooo much faster and safer to drill and tap the end of the motor shaft and use a short piece of threaded rod sharpened to a point with a t-nut with lock nut to hold the t-nut in place , AND you would have been done before you got the 3 holes drilled in the pulley. Not to mention no time for wood circle or brackets. Look I give you this ( you got it done ) but you went the longest way around to make something that not safe. One of those brackets hits you and your going to the emergency room. Next time drill motor shaft and tap, Then use threaded rod say 3 in will do. Sharpen point add 2 nuts and a t- nut The 1st but looks it to the shaft, The 2nd nut is a lock for the t- nut . The point on the threaded rod keeps center and t - nut spins your work . Simple and takes less room than the pulley that you could have gotten rid of anyway.
NO SE PERO LO VEO UN TANTO PELIGROSO POR LOS ÁNGULOS EXPUESTOS EN LUGAR DE UN PUNTO CENTRAL. TAMBIEN UN POCO MAS DIFICIL DE CENTRAR. PERO PARA MUCHAS COSAS ES UNA BUENA IDEA. .
Excelende idea. Pero... yo pondria un disco de hierro de 1/4" de espesor para que los puntos de sujecion de la madera sean mas seguros y en el pedestal donde se apoya el portacuchillas y la de contrapunta le pondria un diagonal para que no se regrese al dar presiòn tanto al trabajar como de sujetar la pieza a tornear. Dios le bendia siempre.
Super video! I applauded for $10.00 👏👏👏
Thanks my frind 🤘
Прикольная штука, для получения по лбу куском дерева )
Chế máy tiện tại nhà rất tuyệt vời Xin cảm ơn anh đã chia sẻ với khán giả
?
I was looking for some kind of equipment to find out the exact center of round pieces, Thanks for such a wonderful idea, GOD bless you abundantly.
Me too john chacha
@@PrashantKumar-zm3yq me
Amazing
Application theory at its best.
hello from iraq well done i respect your idea
you make useful wood lathes
…. Народ не устаёт придумывать разные варианты станков, только бы не покупать заводские… Правда, экономия , при этом, очень солидная … 😊Удачи и творческих успехов ! …
Благодаря ☺️🍀👍
Very good. Show. 🙂🙂
nice creative
Excelente idea lo pondré en práctica
Excellent work, thanks for sharing your knowledge.
Хареса ми идеята за универсала, но опората на длетото не е стабилна, вибрира!!! Поздрав от България!
Благодаря, поздрави от България също
love it...if we don t see you round we see you square..
It works well, looks very practical, and does what has been intended for hobbyists, however besides some minor modifications on the chuck, the railing, and perhaps a safety shield in front of the workstation are doing an awesome job.
Yes ok....nice good👍👍
Greeting from indonesia...tanks
I like your video.,.👍👍👍
Очень нравится мне этот прекраснвйканал. Советую всем, любознательным. Есть чему поучиться.
?
Estoy fabricando uno con partes metalicas de desecho, solo adaptare el cabezal de tu idea, me parecio muy buena.
Saludos y bendiciones
Creative video, thanks for sharing it :)
تحياتي وتقديري 🌷❤️
Its a wonderful idea full support i see around
hi, your work is very nice
Great job
Gracias por el vídeo, muy buena idea.
Yes⭐
Человек не имеет даже малейшего представления о работе на токарном станке. Если этот станок лучший, и он доволен результатом, то трудно представить какие были первые.
?
величайший рукожеп
Muito legal o torno parabéns pelo o seu trabalho show 👍👍
Very good idea ! 👌👏👏👏
It wouuld have been better if you had provide dimention of wooden parts 👍
thank you
How you connected it to the electricity
Гениально!
This is the best homemade lathe clamp design ever! It seems capable for big size of wood, thanks for sharing!
Интересно,через какое время самадельщик лишится все пальцев,?
Ok very god
Your videos, skills and ideas are great.
One request to make your videos more interesting is to make it shorter by not showing repeat activity.
🌺🇮🇳🇺🇸🌺
*LOVE THE WAY YOU FOUND CENTER OF CIRCLE WITH SQUARE!!*
motor hava menfezlerini kapatman talaşların girmesini önler. bu motor için hayati önemli.
Idia intelegent Verry good,👍👍👍👍👍🇲🇦🇲🇦🇲🇦🇲🇦
فكرة رائعة أتمنى لك التوفيق من المغرب 🇲🇦🇲🇦🇲🇦👍👍👍👍👍
اشغلنك إݣا وين المليح أفدا يرضو ربي👍👍👍🇲🇦🇲🇦🇲🇦🇲🇦🌹🌹🌹🌹🌹
Une bonne idée intelegent homme je souhaite une bonne avenir au futur👍👍👍🇲🇦🇲🇦🇲🇦🇲🇦🌹🌹🌹🌹🙏🙏🙏🎩🎩🎩
Rapaz idéia muito inteligente testado e aprovado parabéns cidade de Sorriso MT Brasil abraço
Foarte frumos.
Thanks bro!!!
👏👏👏👏
Nice
love the warning at the start of the video, really appropriate in this case.
Buen torno
Wonderful idea but put a guard around those bolts!
Big thank you, I have a motor in a washing machine that I will extract out & I want a lathe for metal & wood, let start with wood!
13:09 Please, where is the video link with many wiring diagrams?
I can't find it.
Вот это суходрочка!!!
Excelente trabalho parabéns 💯👏👏👏👏👏👏
Yeah,
I'd be a bit leery of using that as a direct-drive unit
Not too keen on nuts & bolts, with shards of angle iron, being flung at me at17K rpm
(I'm guessing the rpm)
You could add some nail spikes around the perimeter of that faceplate to increase it's aesthetic appeal, I guess
These motors from washing machines usually run at 1200 to 2300rpm. Wooden chucks if made from birch plywood and angle iron are a good and safe method. Particle board is never a good idea, even when it is covered with melamine. The only structural problem I see is in the tailstock - a triangle is needed to stiffen up the construction.
2 de se vi
Most probably this motor works at 1300-1400 RPM as they are 4-pole design. Nothing to worry about.
Anda seorang yang genius and creative... salam sukses selalu ya 👍👍
This right here. I would NOT trust that """"chuck"""".
You're a wise man ingenious well done. Can't get enough of your video stay safe in these uncertain times
Muito bom genial
Muy bueno, gracias. Saludos desde las sierras de Córdoba Argentina...!! 👍👌💪🇦🇷
I would suggest using solid hardwood for the faceplate. Particleboard has no strength and screws can pull out easily.
20/20
Fine work.. thank you
I have a really nice Bosch washing machine motor that I pulled and it is seriously fast. But it doesn't have the same torque yours does. What are the specs on it and where did you find it?
Merci cordialement
Нормальная конструкция! Для обеспечения ТБ нужно установить защитный кожух, что элементарно сделать для данного патрона, причём даже навскидку есть как минимум три варианта.
JENIAL EXCELENTE MI PANA
А было бы 10 уголков. Показывал бы, как просверлить все 10?
Salam subc dari amanah73👍👍👍
Muito bacana mesmo parabéns 👏👏👏
Excellent brother
Excelente diseño Amigo , Muy Buen Trabajo , permíteme copiarlo , además me has dado idea para un torno para bujes de bronce o aluminio . FELIZ NAVIDAD Gracias , Gaspar
🙏👍👍
buena idea para empesar gracias amigo
Para hornear madera se utiliza la uña que entra fácil en la madera más rápido y seguro, aproximadamente este plato es más metal y este no aguantaría ni el peso ni la presión de corte.
very creative
Might be good for smaller objects like the dowel for an upright paper towel holder (or actual dowels). But your not going to be turning out any bowls of significant size (pun intended). On that point it leaves a lot to be desired. But then again so do model rockets, RC aircraft/boats/cars, and drones.😏
Ideja gut,realizacija šajze.
Great video. But it seems a bit unsafe. Wood used for tools of this sort can go 'crack', and hit you in the face. A lathe should have metal and steel components only.
Parabéns, Muito legal sua idéia. Inspiradora!!! Abraços ( São Paulo, Brasil)
Hola esta buena la idea pero le faltaria una caja de seguridad o tope para tapar los ángulos y tornillos al girar por asi cómo está es un peligro . Pero muy buena idea 🇦🇷
At 15.20. You are starting the Motor with your hands. So obviously you haven`t got a capacitor connected,which also means that the secondary winding is not connected.
Very nice point made. The winding can be done carefully so that it can be self start and also if more copper is filled into the slots, then it can be made into heavy duty motor.
If I were to design this motor, I would make it in chain winding configuration which can even save more energy and almost never heats up on long duration of operation.
Hola tenes para enviar las descripción o croquis para armarlo gracias
👌
Please mujhe bataw yeh konsi motor hai
E O MAIOR MADJORIS!
🇧🇷impressionante
Liked the clip. A little long. The chuck might be put on a hand drill. There are a lot of other clips about how to use a hand drill to make a lathe. So the newer chuck might be an upgrade?
Ese sistema no garantiza el centrado.
Every time I see this Video my skin is chills. I really have the feeling that a very SERIOUS accident can come at any time
Kn
@@hugojavierunriccemarquina1800 %aá%12
YUP! This one gives me the creeps.
R5454545454545455444d
@@jagboy69 Precisely, we are 6 in this musical group and everyone was thrilled to see this diabolic invention. But everyone with goosebumps
The idea it s wonderfull but using the wood...it s from away a big danger!!!
It can also me made from iron instead of wood. That will be more durable and safer option.
Richtig gut.
11:45 КАЖЕТСЯ, ПАРЕНЬ ГОТОВИТСЯ К САМОУБИЙСТВУ!
Maravilhoso
it is a good DIY lathe just curious if the chuck can last long with hardwood
No
Bom trabalho
Very very very ho...'
Ótimo, parabéns.
Great idea , BUT I was cringing when you put your hand next those brackets as they are spinning to sand that piece. Ok it would have been soooo much faster and safer to drill and tap the end of the motor shaft and use a short piece of threaded rod sharpened to a point with a t-nut with lock nut to hold the t-nut in place , AND you would have been done before you got the 3 holes drilled in the pulley. Not to mention no time for wood circle or brackets. Look I give you this ( you got it done ) but you went the longest way around to make something that not safe. One of those brackets hits you and your going to the emergency room.
Next time drill motor shaft and tap,
Then use threaded rod say 3 in will do.
Sharpen point add 2 nuts and a t- nut
The 1st but looks it to the shaft,
The 2nd nut is a lock for the t- nut .
The point on the threaded rod keeps center and t - nut spins your work . Simple and takes less room than the pulley that you could have gotten rid of anyway.
Jerônimo Menezes Freitas. Legal demais Mestre, parabéns e Obrigado pela Dica
Ďďďþ
NO SE PERO LO VEO UN TANTO PELIGROSO POR LOS ÁNGULOS EXPUESTOS EN LUGAR DE UN PUNTO CENTRAL. TAMBIEN UN POCO MAS DIFICIL DE CENTRAR. PERO PARA MUCHAS COSAS ES UNA BUENA IDEA.
.
실용성이 떨어집니다.엥글이 휘여져서 실패봅니다.
Great, but we in Russia make it out of paper. ;))
Thats because your government won't allow you to own real tools! LOL
@@jennings20100 XD
Mas broo caranya buat pelumas ngebor minyak apah?
Excelende idea. Pero... yo pondria un disco de hierro de 1/4" de espesor para que los puntos de sujecion de la madera sean mas seguros y en el pedestal donde se apoya el portacuchillas y la de contrapunta le pondria un diagonal para que no se regrese al dar presiòn tanto al trabajar como de sujetar la pieza a tornear. Dios le bendia siempre.
Dedil! If y have 100 holes, y will be show dill it all?