After buying my first home back in August, these videos help. Google has also been a big help to assure me it's working properly. I panicked the other day when I heard the valve switch when it went into defrost mode. When I went outside, the compressor was running, but not the fan. Of course the worst thing popped into my head, like great it's broke. Then after some researching, I was reassured it was working as it should. So much to learn about these heat pumps.
Phillip you missed the entertaining part of the defrost cycle. When it ends, the outdoor fan comes back on and since the coil was heated, it will blow a big cloud of water vapor (depending on conditions) which looks like a big cloud of smoke.
The old Thermo King MD-II's used to have something similar to this, but it was more of a round cylindrical shape, enabled mechanically by the Hot Gas circuit when calling for defrost or heat. They were fully serviceable, I rebuilt many of them......GLAD IT'S NO LONGER A STANDARD LOL!!!
Reversing valve heat pumps have been around 60 plus years I have installed them for 42 years and are 31/2 times more efficient than electric strip heat , and 80% of dealers are afraid of a heat pump, payback for the 200-400 dollars more in cost is less than 1 season Straight Electric heat only should be outlawed for being the Blackest energy one can use for heating
Mr. Clint 1st wanna say I'm litterly discover this Video from what I understand this video is very clearity on Revers valve ... correct me during the video it mention ' Pilot(🔥) valve'
You show that just after the expansion Device the refrigerant is in a Flash Gas state when really for the system to work efficiently it is in a high pressure liquid state so most of the outdoor coil will actually be filled with liquid. Near the output of the cooling coils will have a liquid flash gas interface. At the input the pressure is high but at the output the pressure is lower and should be all gas. Also heat is going into the Outdoor coil and this is being pumped from the outside to the inside. Latent heat of Evaporation is the real clever part of heat pumps. Heat is going in but temp is not rising,
Great video.. one thing that puzzles me - when the system is in heating-mode, the refrigerant lines are used for the opposite purpose of cooling. Since the lines are not the same size ( my suction line is 3/4 and liquid is 5/16), aren't the lines improperly sized upon reversing? Is there a performance loss in heating mode due to the improper sizing.
Here in Texas, the heat mode is used less. I think I'll set it up for energised for heat and label all the wires so future techs to keep them from pulling their hair out.
Thanks for the valve overview - you really provide a valuable service for the industry. Just one thing that would be helpful be is if you go over the failure modes of a reversing valve. From your overview, it seems pretty bullet proof.
I have seen only two failures. One is when the sliding piston gets stuck and then it will only run in one mode. Not so bad if you're calling for heat and the reversing valve is stuck in the heating position but then it is really bad when you have a call down the line for cooling on a hot day and the unit is putting out hot air. The second one is much more difficult to diagnose for someone who does not have a good understanding of a refrigerant cycle. I have seen reversing valves leak internally, and what happens is a large part of the hot gas from the compressor discharge leaks in the reversing valve directly into the suction line of the compressor. It will sort of equalize the system pressure and resemble conditions of bad compressor valves but by taking superheat, subcooling and measuring temperatures of all the lines in and out of the reversing valve you can differentiate between the two conditions.
@@lilkenny123123 Hi Kenneth. I am recently retired but I worked as an HVAC tech for about 40 years. I worked in some high-volume shops and after a while you basically see just about every problem you could imagine.
I wouldn't be where I am today both mentally and in the hvac install trade and continually progressing rapidly in said trade and mental wear withal and know how if it wasn't for your intelligence and generosity of openly teaching the details of the trade 🤗🤗🤗🧠💪👨🎓🧑🔧🕵♂️🤔🤔
its confusing that the refrigerant is labeled as a flash gas between the metering device and evap coil, in cool mode. because while some of the refrigerant is changed from liquid to vapor after metering device, its still in a saturated state (liquid still present) until it passes fully through the evap coil on a normally operating system. then it absorbs heat, and boils into vapor. right?
Hi Bryan how r u! I got questions I do get it hot gas come from discharge through capillary to shift reversing valve but where is suction line gas come from? Because I see the flow in video suction gas is not come from common suction line, low gas flow back to common suction! Where low gas come from? It’s doesn’t look like to from common suction? Thanks
Ok I have about a dozen apartments connected to one master/slave unit. How can one apartment be running heat and another be running AC on the same unit?
This is great. Thanks for clearly explaining this so well and providing the visuals to go with it. Helps alot in understanding how a heat pump systems works.
Do you have any section drawings or diagrams that you can share for a heat pump system in a residential high-rise? i.e. whole package install including drip pan to external drip pipe outlet on the facade of a building?
There are two ways to charge a heat pump accurately. Weigh it in if you know the correct amount or charge it in cooling mode using the charging chart. If you have a performance chart you can use that in heating mode but the charge will not be accurate.
This was SUPER helpful, thank you; particularly the info. concerning Rheem & Ruud being manufacturers that "fail to" COOLING MODE. With that said, I have a SANHUA Reversing Valve (from Goodman) that when putting nitrogen through the discharge, appears to FAIL TO COOL. Does anyone know if this is accurate? Much appreciated! :)
Thanks! Installed a Nest Theromostat in my Apt about a year ago almost and I had issues running. Trying to figure out why when i run the AC its pumping out hot air! Little did I know it was not gas powered as I though and was a heat pump! I just though it full on reversed the compressor and didn't realize there is a valve that does that part. Only thing I don't like about it is that 1) since it uses the compressor it is just as expensive to run as the AC and 2) it doesn't get as hot as a gas or electric and takes longer to warm up my apartment and thus costing me more money. Normally my electric bill is 70-100 but its been 130-150 this year for winter.
This is so elegant in it's simplicity, I am glad I was curious as to how it worked. Also I am surprised these haven't been implemented absolutely everywhere 20 years ago.
As always, great video. But I have a curiosity. In systems that are pressure equalized in off mode such as a Goodman or Carrier, I can still hear an audible sound of the reverser valve when I supply 24 V to “O”. (Clank) I understand why this happens in a non-bleed TXV systems such as Trane, And I also understand that compressor force or pressure differential is the actual prime mover of the “canoe”. I’m just wondering why I can hear the same thing in systems that are basically at the same pressure on both sides on a non-running system. I guess that little pilot valve is just that loud. Perhaps I just answered my own question.
Solenoid will still operate so you'll hear the plunger, but there won't be a pressure differential in the pilot tubes. The main valve essentially has gas dampening as the gas is pushed out of the opposite side and won't make a clank.
If I only have 4 wires going to my heat pump from Thermostat, couldn't I just put a jumper inside the heat pump so the reversing valve would be energized whenever the AC came on in the winter and run the heat pump in AC mode? In summer disconnect the jumper or put in a toggle switch?
I have a heat pump in my house and it's cost effective to run, but the only thing I don't like about heat pumps in general, is they put twice the wear on the compressor because it runs all year long
Thank you so much for this video. I work for AC manufacturer and always been interested in stuff like that. Years of study but only practice verifies knowledge and videos like yours are very helpful to imagine and understand operation of the individual parts. I discovered you by reversing valve ;) I subscribed your channel and want to wish you all the best :)
I would like to add a reversing valve to.a.common refrigerator so that it can heat up as a proofing chamber when needed. As the conpressor on a fridge is not as powerful, will a reversing valve out of a heat pump still work and be able to switch? Or not ..
Amp draw on compressor is much higher on Heat mode vs cooling. I get about 2500 watts to 3000 watts on 3 ton in cooling depending on outdoor temp, but heating is 2900 to 3500 and get outside TXV action after 10 mins run causing a sinusoidal current draw varying about 200 watts in heat mode only if you graph wattage, all normal for my Heil HP 3 ton R22.
That hissing noise you heard is called hydraulic hissing. It's just the flow of the fluid you hear through the pipes, same way you hear water flow through water pipes in your home. The expansion valve or any restrictive device which interrupts the flow will cause a noise. Same way if you have roof racks on the roof of a car, you hear a whistling noise because the flow of air is interrupted.
*No complicated technical jargon, just simple explanation of how it works; Super easy to understand,* *Thank You! Thank You! Thank You!* | 2 years ago my Carrier single package heat pump PH4Z-060 failed to provide heat. I called an HVAC company to troubleshoot and repair, the technician diagnosed and found the heat strip was burned out and the galvanized housing/box was rusted. The replacement part was unavailable according to the expert. *Long story short, I don't believe that he checked the electromagnetic coil and reversing valve.* My heat pump is 8 years old and I'm considering a Split System to replace it. *'Care to share any advice?*
On a call for heat at the thermostat the reversing valve is not energized and is in heating mode, but when you call for cooling at the thermostat then the reversing valve reverses the flow of refrigerant.
Very Excellent video. I am replacing the thermostat on an older Nordyne Heat pump with a newer Sensi "Smart" Thermostat made by Emerson. Based on your video may I assume the reversing valve in this Nordyne unit is energized in the cooling mode? May I assume the "O" terminal (orange wire) goes to the reversing valve? This unit has indoor air handler for supplemental resistance heat or emergency resistance heat. The old thermostat is not programmable and strictly mechanical. It has 2 mercury switches in it for main (compressor) and supplemental (resistance) heat. I am a retired technician. I did some HVAC but that was not my specialty. The new thermostat is programmable and can also be controlled via Wi-Fi or mobile data. Larry Retired Sears Tech Electronics and appliance repair 43 yrs
Back in the early 60s, I had a CARRIER HP PACKAGE Looking like a large window unit at the BRONX ZOO, where the took care of BABY animals, but we did NOT have the instrumation, we now take for granted All you had were service thermomitors So trying to find a bad 3 way valves, was NOT obvious, unless it was REALLY LEAKING between high/low Another thing NEVER HIT A VALVE BODY, as you can do DAMAGE TO IT CREATING THE SAME PROBLEM CAUSED BY THAT VALVE ! Cheers 🇺🇸🇺🇸🇺🇸🇺🇸. HAPPY NEW YEAR ALL .
Thank you for this. Hmm.. I wonder if this could be the problem with my system-- the reversing valve not working properly. Back during winter we turned the heat on but after it warmed up a bit we turned it back to cool mode but it was heating instead. The outside compressor (which was 12yrs old) died. Took a few months to get someone to actually come out and diagnose. We replaced the outside unit with a matching unit designed to work with our inside unit (Trane brand). Had it professionally installed and cooling was working. But now it is set to cooling to 70° but its heating instead (got to 77). I turned it off and things cooled off. I'm hoping its not something wrong with the new unit (although it is under warranty) but maybe its the reversing valve. Where exactly is the reversing valve? Is it inside the internal unit or the outside unit or somewhere in between?
My reversing valve is not moving all the way in the air conditioning mode (cold). My head pressure is normal but my suction pressure is like 10 PSI. Is there a way to free up the valve by tapping on it or applying heat? Is there a way to get a valve that is not shuttling properly to move freely. It's an R22 system that holds a fair amount of Freon so I'd like to try to fix it without cracking open the system. Thanks if anyone has any ideas.
The “evaporator” or outdoor coil saturation temperature is below the outdoor air temperature. This creates the heat transfer. So, it can be -5F outside with a -20F sat temp and the refrigerant will absorb heat energy to transfer indoors via the compressor. Pretty neat.
Since I can't get a HVAC INSTALLER TO CHANGE an old built-in version to heat pump where can I get a valve there are utube tutorials on how to pump out the old refrigerant out and how to fill but nothing on the valve until yours
This is very helpful for me to understand how to maintain my own equipment at home. Thank you. I am very interested to know the sequence of events that occurs during a defrost cycle of a heat pump. The compressor receives an intense shock to the system when this valve actuates, and I would like to know if compressors for heat pumps differ from simple air conditioners in a way that compensates for this shock load they receive regularly. Also, I have seen systems that measure pressure differentials between outside and inside the outside unit to determine when to operate defrost cycles rather than simple temperature differentials or timers. Is the efficiency gained by a pressure differential system worth the added expense and complexity?
So if too cold outside , no warmeth the inside ? I thought it used the indoor air to pull the heat and redirect it back inside somehow, but also explains why I couldnt figure out how it worked...I think my brain didn't want it to be like that because it limits the application to the warmth available outside
Thanks for sharing, great video and illustrations. Understand that the pilot valve does the shift, at what pressure should the refrigerant be when in heat mode? I’m not sure but I don’t think my valve is working properly, I’m not getting to desired temperature inside the house. In heat mode, the line going to the evaporator inside doesn’t feel like it’s getting hot enough to provide enough heat to warm up the house. I put my thermometer on the line going into the air handler, ( in between the insulation and copper line) to get a reading as it leaves the outside unit, the temperature reads around 67 degrees F. The gas should be a much higher temperature going to the air handler right?, so is my revering valve not working right or is there something else I should be looking at? Any advice is much appreciated.
We had an electromagnetic coil on the pump that kept making the contactor to switch in and out. But we didn't know what it was making it do that we called our boss he told us about the magnet. My question is how did he know??
Спасибо тебе хороший человек ,и который читает этот комментарий понимающий английский язык ,будь добр пишите этому блогеру что бы он добавил русский субтитры ,огромные спасибо и блогеру и передающию мою просьбу 🤗☝️👍👍🤝
Thanks for clearly explaining how the solenoid works
After buying my first home back in August, these videos help. Google has also been a big help to assure me it's working properly. I panicked the other day when I heard the valve switch when it went into defrost mode. When I went outside, the compressor was running, but not the fan. Of course the worst thing popped into my head, like great it's broke. Then after some researching, I was reassured it was working as it should. So much to learn about these heat pumps.
Phillip you missed the entertaining part of the defrost cycle. When it ends, the outdoor fan comes back on and since the coil was heated, it will blow a big cloud of water vapor (depending on conditions) which looks like a big cloud of smoke.
50 dislikes? Must be plumbers..
Or Failed hvac techs
Do not worry. This is an excelent video.
😆 word.
Most definitely plumbers hate vibes, this was a thorough explanation.
Or painters
These animations are so fascinating.
That was a very simple explanation. Thank you
The old Thermo King MD-II's used to have something similar to this, but it was more of a round cylindrical shape, enabled mechanically by the Hot Gas circuit when calling for defrost or heat. They were fully serviceable, I rebuilt many of them......GLAD IT'S NO LONGER A STANDARD LOL!!!
Hot gas bypass...
Reversing valve heat pumps have been around 60 plus years I have installed them for 42 years and are 31/2 times more efficient than electric strip heat , and 80% of dealers are afraid of a heat pump, payback for the 200-400 dollars more in cost is less than 1 season
Straight Electric heat only should be outlawed for being the Blackest energy one can use for heating
Mr. Clint 1st wanna say I'm litterly discover this Video from what I understand this video is very clearity on Revers valve ... correct me during the video it mention ' Pilot(🔥) valve'
Could you tell me how to turn off my AUX HEAT on my water heat pump Please
Ruud, Rheem, Gree Flexx, MrCool Universal, ACPro X Series
Clearly understood and thanks
You show that just after the expansion Device the refrigerant is in a Flash Gas state when really for the system to work efficiently it is in a high pressure liquid state so most of the outdoor coil will actually be filled with liquid. Near the output of the cooling coils will have a liquid flash gas interface. At the input the pressure is high but at the output the pressure is lower and should be all gas. Also heat is going into the Outdoor coil and this is being pumped from the outside to the inside. Latent heat of Evaporation is the real clever part of heat pumps. Heat is going in but temp is not rising,
Thanks
12 year hvac tech here and this guy sure does know what he's talking about 👍
Vrey good shering gues
Great video.. one thing that puzzles me - when the system is in heating-mode, the refrigerant lines are used for the opposite purpose of cooling. Since the lines are not the same size ( my suction line is 3/4 and liquid is 5/16), aren't the lines improperly sized upon reversing? Is there a performance loss in heating mode due to the improper sizing.
Here in Texas, the heat mode is used less. I think I'll set it up for energised for heat and label all the wires so future techs to keep them from pulling their hair out.
Very educative, thank you.
Thanks for the valve overview - you really provide a valuable service for the industry. Just one thing that would be helpful be is if you go over the failure modes of a reversing valve. From your overview, it seems pretty bullet proof.
Coil engerzied het pump systom seftey dves good thanlyoi gues rebersing valved is full ok
I have seen only two failures. One is when the sliding piston gets stuck and then it will only run in one mode. Not so bad if you're calling for heat and the reversing valve is stuck in the heating position but then it is really bad when you have a call down the line for cooling on a hot day and the unit is putting out hot air. The second one is much more difficult to diagnose for someone who does not have a good understanding of a refrigerant cycle. I have seen reversing valves leak internally, and what happens is a large part of the hot gas from the compressor discharge leaks in the reversing valve directly into the suction line of the compressor. It will sort of equalize the system pressure and resemble conditions of bad compressor valves but by taking superheat, subcooling and measuring temperatures of all the lines in and out of the reversing valve you can differentiate between the two conditions.
Revrsing blockinn dreact fixing
@@Howie875 wow how long you been doing Hvac?
@@lilkenny123123 Hi Kenneth. I am recently retired but I worked as an HVAC tech for about 40 years. I worked in some high-volume shops and after a while you basically see just about every problem you could imagine.
Thank you for your efforts
I wouldn't be where I am today both mentally and in the hvac install trade and continually progressing rapidly in said trade and mental wear withal and know how if it wasn't for your intelligence and generosity of openly teaching the details of the trade 🤗🤗🤗🧠💪👨🎓🧑🔧🕵♂️🤔🤔
its confusing that the refrigerant is labeled as a flash gas between the metering device and evap coil, in cool mode. because while some of the refrigerant is changed from liquid to vapor after metering device, its still in a saturated state (liquid still present) until it passes fully through the evap coil on a normally operating system. then it absorbs heat, and boils into vapor. right?
Thank you so much sir,this one is pretty cool,god bless and have a great new year
These animations are so valuable, thanks Brian, I am sharing with my fellow techs.
Hi Bryan how r u! I got questions I do get it hot gas come from discharge through capillary to shift reversing valve but where is suction line gas come from? Because I see the flow in video suction gas is not come from common suction line, low gas flow back to common suction! Where low gas come from? It’s doesn’t look like to from common suction? Thanks
Thks:
?How much more is a heat pump more than an air conditioner?
?Should I always just get a heat pump over an air conditioner?
Sir please tell me explain me check valve for split clima. I dont know how it working
I appreciate your efforts to explain reversing valve function in detail
How do u feel about the hook for brazing?
Ok I have about a dozen apartments connected to one master/slave unit. How can one apartment be running heat and another be running AC on the same unit?
Thank you so much sir
I love This channel ❤️
Great video, can you do one on replacing the reversing valve?
This is great. Thanks for clearly explaining this so well and providing the visuals to go with it. Helps alot in understanding how a heat pump systems works.
SO it's kind of like a trumpet. And that's the reason it takes 5 minutes to actually turn on.
What a soothing reassuring voice!
Just saw one changed out today. Cool to see how it works.
Do you have any section drawings or diagrams that you can share for a heat pump system in a residential high-rise? i.e. whole package install including drip pan to external drip pipe outlet on the facade of a building?
Can you check pressures in heating mode with a HP? If so what are they. If not, then checking in normal operation cooling is how it’s done.
There are two ways to charge a heat pump accurately. Weigh it in if you know the correct amount or charge it in cooling mode using the charging chart. If you have a performance chart you can use that in heating mode but the charge will not be accurate.
Who is the other manufacturer that uses the B terminal?… Test question.
Rheem and rudd use the b terminal.
4:33 does all the heat come from outside? How much comes from compressing the gas? If any?
Very well said. You are so on point!
gracias por el video. Si los traduces al español seria perfecto.
I really learn a lot from your videos. Thanks 👍
One important thing is if the system get a leak, reversing valve is not going to work properly.
This was SUPER helpful, thank you; particularly the info. concerning Rheem & Ruud being manufacturers that "fail to" COOLING MODE.
With that said, I have a SANHUA Reversing Valve (from Goodman) that when putting nitrogen through the discharge, appears to FAIL TO COOL.
Does anyone know if this is accurate?
Much appreciated! :)
Thank u Jesus of HVAC 🙏🏿 for showing us da way
Thanks! Installed a Nest Theromostat in my Apt about a year ago almost and I had issues running. Trying to figure out why when i run the AC its pumping out hot air! Little did I know it was not gas powered as I though and was a heat pump! I just though it full on reversed the compressor and didn't realize there is a valve that does that part. Only thing I don't like about it is that 1) since it uses the compressor it is just as expensive to run as the AC and 2) it doesn't get as hot as a gas or electric and takes longer to warm up my apartment and thus costing me more money. Normally my electric bill is 70-100 but its been 130-150 this year for winter.
Thanks for the tips, there's always something to be learned , that's why this trade is cooler than rocket science
Wow, what an excellent description.
This is so elegant in it's simplicity, I am glad I was curious as to how it worked. Also I am surprised these haven't been implemented absolutely everywhere 20 years ago.
As always, great video. But I have a curiosity. In systems that are pressure equalized in off mode such as a Goodman or Carrier, I can still hear an audible sound of the reverser valve when I supply 24 V to “O”. (Clank) I understand why this happens in a non-bleed TXV systems such as Trane, And I also understand that compressor force or pressure differential is the actual prime mover of the “canoe”. I’m just wondering why I can hear the same thing in systems that are basically at the same pressure on both sides on a non-running system. I guess that little pilot valve is just that loud. Perhaps I just answered my own question.
Solenoid will still operate so you'll hear the plunger, but there won't be a pressure differential in the pilot tubes. The main valve essentially has gas dampening as the gas is pushed out of the opposite side and won't make a clank.
If I only have 4 wires going to my heat pump from Thermostat, couldn't I just put a jumper inside the heat pump so the reversing valve would be energized whenever the AC came on in the winter and run the heat pump in AC mode? In summer disconnect the jumper or put in a toggle switch?
Nice brother
Thanks
Those look like trouble. Heheh.
Great video. Thanks
I have a heat pump in my house and it's cost effective to run, but the only thing I don't like about heat pumps in general, is they put twice the wear on the compressor because it runs all year long
Heat pumps are weird!
Thank you so much for this video. I work for AC manufacturer and always been interested in stuff like that. Years of study but only practice verifies knowledge and videos like yours are very helpful to imagine and understand operation of the individual parts. I discovered you by reversing valve ;) I subscribed your channel and want to wish you all the best :)
I would like to add a reversing valve to.a.common refrigerator so that it can heat up as a proofing chamber when needed. As the conpressor on a fridge is not as powerful, will a reversing valve out of a heat pump still work and be able to switch? Or not ..
Amp draw on compressor is much higher on Heat mode vs cooling. I get about 2500 watts to 3000 watts on 3 ton in cooling depending on outdoor temp, but heating is 2900 to 3500 and get outside TXV action after 10 mins run causing a sinusoidal current draw varying about 200 watts in heat mode only if you graph wattage, all normal for my Heil HP 3 ton R22.
Het revals valve not working stome runing need pleas explain any sloushion fee pleas..
@@jollyscaria1922 Don't follow you??
@@jollyscaria1922 it was well done. Very simple to grasp thanks a lot
Awesome video!! Why does it hiss when it switches over?? I know it's reliving pressure but you explain it do we'll.
It only hiss wen da AC getz turn on
That hissing noise you heard is called hydraulic hissing. It's just the flow of the fluid you hear through the pipes, same way you hear water flow through water pipes in your home. The expansion valve or any restrictive device which interrupts the flow will cause a noise. Same way if you have roof racks on the roof of a car, you hear a whistling noise because the flow of air is interrupted.
Great video! What is the evaporators refrigerant maximum temperature heating mode?
My Mitsu 3-zone has both a reversing valve and a "2-way" valve. Any idea what the latter does?
Thanks for your video
When the cooling demand is met in a HP, does it first turn the compressor off or the reversing valve (assuming reversing valve energized is cooling)?
Thanks for sharing this video. It was very clearly explaining and very useful. Great job
Why wouldn't you just use the solenoid to move the reversing valve? Why involve gas through tiny tubes to create problems?
HVAC School, Thank you very much
How to know the this valve its energized when cooling or heating?.i appreciate your answer.great channel by the way
Excellent, great content and animation.
*No complicated technical jargon, just simple explanation of how it works; Super easy to understand,* *Thank You! Thank You! Thank You!* | 2 years ago my Carrier single package heat pump PH4Z-060 failed to provide heat. I called an HVAC company to troubleshoot and repair, the technician diagnosed and found the heat strip was burned out and the galvanized housing/box was rusted. The replacement part was unavailable according to the expert. *Long story short, I don't believe that he checked the electromagnetic coil and reversing valve.* My heat pump is 8 years old and I'm considering a Split System to replace it. *'Care to share any advice?*
At what point is the reversing valve allowed to shift? Is there any point in it's movement where it can dead-head the discharge line?
On a call for heat at the thermostat the reversing valve is not energized and is in heating mode, but when you call for cooling at the thermostat then the reversing valve reverses the flow of refrigerant.
Very Excellent video. I am replacing the thermostat on an older Nordyne Heat pump with a newer Sensi "Smart" Thermostat made by Emerson. Based on your video may I assume the reversing valve in this Nordyne unit is energized in the cooling mode? May I assume the "O" terminal (orange wire) goes to the reversing valve? This unit has indoor air handler for supplemental resistance heat or emergency resistance heat. The old thermostat is not programmable and strictly mechanical. It has 2 mercury switches in it for main (compressor) and supplemental (resistance) heat. I am a retired technician. I did some HVAC but that was not my specialty. The new thermostat is programmable and can also be controlled via Wi-Fi or mobile data.
Larry Retired Sears Tech Electronics and appliance repair 43 yrs
Back in the early 60s, I had a CARRIER HP PACKAGE Looking like a large window unit at the BRONX ZOO, where the took care of BABY animals, but we did NOT have the instrumation, we now take for granted All you had were service thermomitors So trying to find a bad 3 way valves, was NOT obvious, unless it was REALLY LEAKING between high/low Another thing NEVER HIT A VALVE BODY, as you can do DAMAGE TO IT CREATING THE SAME PROBLEM CAUSED BY THAT VALVE ! Cheers 🇺🇸🇺🇸🇺🇸🇺🇸. HAPPY NEW YEAR ALL .
Thank you for this.
Hmm.. I wonder if this could be the problem with my system-- the reversing valve not working properly. Back during winter we turned the heat on but after it warmed up a bit we turned it back to cool mode but it was heating instead. The outside compressor (which was 12yrs old) died. Took a few months to get someone to actually come out and diagnose. We replaced the outside unit with a matching unit designed to work with our inside unit (Trane brand). Had it professionally installed and cooling was working. But now it is set to cooling to 70° but its heating instead (got to 77). I turned it off and things cooled off. I'm hoping its not something wrong with the new unit (although it is under warranty) but maybe its the reversing valve. Where exactly is the reversing valve? Is it inside the internal unit or the outside unit or somewhere in between?
My reversing valve is not moving all the way in the air conditioning mode (cold). My head pressure is normal but my suction pressure is like 10 PSI. Is there a way to free up the valve by tapping on it or applying heat? Is there a way to get a valve that is not shuttling properly to move freely. It's an R22 system that holds a fair amount of Freon so I'd like to try to fix it without cracking open the system. Thanks if anyone has any ideas.
Make a video on All HVAC tools a Technican and site engineer must have.
Why not just make the slider magnetic and use an electromagnet to move it from side to side?
when the outdoor temp is negative and rad is full of snow how can the pump catch "free calories" ??
(Even though I know that there is de-icing cycle)
The “evaporator” or outdoor coil saturation temperature is below the outdoor air temperature. This creates the heat transfer. So, it can be -5F outside with a -20F sat temp and the refrigerant will absorb heat energy to transfer indoors via the compressor. Pretty neat.
because there are still heat energy inside the outside air even when it is very cold outside.
Since I can't get a HVAC INSTALLER TO CHANGE an old built-in version to heat pump where can I get a valve there are utube tutorials on how to pump out the old refrigerant out and how to fill but nothing on the valve until yours
Valveception!
This is very helpful for me to understand how to maintain my own equipment at home. Thank you. I am very interested to know the sequence of events that occurs during a defrost cycle of a heat pump. The compressor receives an intense shock to the system when this valve actuates, and I would like to know if compressors for heat pumps differ from simple air conditioners in a way that compensates for this shock load they receive regularly. Also, I have seen systems that measure pressure differentials between outside and inside the outside unit to determine when to operate defrost cycles rather than simple temperature differentials or timers. Is the efficiency gained by a pressure differential system worth the added expense and complexity?
So if too cold outside , no warmeth the inside ? I thought it used the indoor air to pull the heat and redirect it back inside somehow, but also explains why I couldnt figure out how it worked...I think my brain didn't want it to be like that because it limits the application to the warmth available outside
Well done, do you have any videos of water to water ground source heat pumps?
But, how many psig operates this valve????
Thanks for sharing, great video and illustrations.
Understand that the pilot valve does the shift, at what pressure should the refrigerant be when in heat mode? I’m not sure but I don’t think my valve is working properly, I’m not getting to desired temperature inside the house.
In heat mode, the line going to the evaporator inside doesn’t feel like it’s getting hot enough to provide enough heat to warm up the house.
I put my thermometer on the line going into the air handler, ( in between the insulation and copper line) to get a reading as it leaves the outside unit, the temperature reads around 67 degrees F. The gas should be a much higher temperature going to the air handler right?, so is my revering valve not working right or is there something else I should be looking at?
Any advice is much appreciated.
I have one problem when put on heat compressor is come hot.just want to know about this.must condenser fan will run on heating
How is a heat pump
Hooked up to a thermostat ? What wires specifically for both cooling & heating ?
We had an electromagnetic coil on the pump that kept making the contactor to switch in and out. But we didn't know what it was making it do that we called our boss he told us about the magnet. My question is how did he know??
It’s just an air conditioner with the forward and reverse switch that’s all It is you can make a heat pump out of any air conditioner
Good sharing waiting next video
So when you’re charging to the liquid line, How do you know when it’s the liquid or suction?
You are a great person
What is the problem when the touching tube in reversing valve (is there any problem if we have touch in 2 line)?
What’s the max -temperature a heat pump is efficient
Tank,you may friend,,
Could you also use a reversing valve to send refrigerant to a heat exchanger to dump heat into a pool vs the condenser?
Y not just put an air-conditioning in backwards
Interesting, thank you
First one me the reversing was located in the a.h.
Спасибо тебе хороший человек ,и который читает этот комментарий понимающий английский язык ,будь добр пишите этому блогеру что бы он добавил русский субтитры ,огромные спасибо и блогеру и передающию мою просьбу 🤗☝️👍👍🤝
All ACs are heat pumps but not all heat pumps are ACs.
Reverse that...
Im so glad I watched this video, thanks for explaining!