Thank you for posting this, it was extremely helpful, however unnecessarily long. In order to get more positive comments, I'm providing some feedback to help you and others who view the video after me. The reason I looked for this video was because my printing was blurry and and there were blank blotches on my print jobs. Content starts at 1:40, which is way too long. I'd remove the content prior to that and recommend using different music instead of EDM or no music at all. If you don't want to talk on your video, then I'd recommend a text graphic overlay with written instructions. It's hard to see the 2 pieces on either side of the printer that you popped out with the screw driver. I figured it out and set them aside. At 3:38, provide written graphic instructions on the type of cloth you used to clean the transfer belt. I assumed lint free cloth, however, since I didn't have one, I used Windex Electronic Wipes, which worked well, however, you have to make sure each section dries before you roll the transfer belt forward with your fingers. You rolled the belt forward and wiped it down until 8:54. That's over 5 minutes of watching you roll the transfer belt and clean it. I'd fast forward through this portion on your video. As I rolled my belt forward, I found the culprit that was making the blank blotches on my print job - a label that was stuck to the transfer belt! I started to try to peel it off with my fingernail, but then stopped because I didn't want to poke a hole in the transfer belt. I found a small plastic tool with a flat edge that was in my computer tool kit. I wet the tip with a little bit of water and gently pushed on the label while it was against the roller (so as to not poke through the belt) and it came right off. I was able to remove the entire label this way. I continued to clean the rest of the transfer belt. There are small white squares on the right hand edge of the transfer belt. I marked one of the squares with a red star so that I knew when I had cleaned the entire belt. You'll notice as you clean the belt and it goes around more than once, it will continue to pick up residue, which is why I made the red star mark so I knew when I completed cleaning the whole belt. At 10:16, you pop the pieces back in, however, it was hard to figure out how to do it. I finally figured it out in 5 minutes. It would help to have text graphic instructions here as well. You have to put the piece back in with the tab facing toward you and slide it into the notch, then push on the opposite end and it pops back in. This video could be 3:00 instead of 13:37. However, it did help me with fixing my printer so I didn't have to buy a new one and waste a whole set of OEM cartridges. Thanks so much!
Amazing, I was about to sell off my printer extremely cheap thinking that I couldnt get the stripes that were printing covering my printed pages and after following this video I was able to save it. Thank you so very much for posting this. I love my printer and I had so many extra ink I was dreading selling it.
I did all this and it didn't help mine at all...I'm wondering ..when cleaning the foam bar in the back did you have to keep wiping until it was completely cleaned...mine has a lot of black on it..I was also wondering if the reason mine was doing this is because I am out of color ink and its dumping too much black
Copies on my LaserJet 200 were coming out with just black streaks...thanks for the fix. It took less than 5 minutes to complete the simple task after watching the 14 minute video. Thanks Again!
I absolutely love the music, I would have watched it even if it was longer, very relaxing. This video is exactly what I was looking for, thank you so much! However my belt would not move so I am not sure how to fix this.
A couple of points - the clips that looked easily removed were not, took a bit of force and they pinged off in the end, went back on a lot easier. I had issues with black marks down the side of the documents doing this did help it but not completely resolve it. I just used kitchen towel, I wonder if I needed some sort of cleaner on it? The belt was difficult to move at first and had to be fairly forceful with it. it did get easier after moving it a few times.
Hello Sir, i have HP m277dw, and i see black line from top to bottom towards 1/4 on the right side, i opened up the back and saw a roller a greenish spongy roller that has a line about the same place 1/4 on the right side, i think it is the 2nd transfer roller? but i can not remove the line it seem it is embedded into the roller. can i replace this roller my self?
Yeah, mine was black streaks that wouldn't go away, even after cleaning (with a dry shop cloth).PROBLEM SOLVED when I replaced the black toner cartridge. THANKS!
Please skip the irritating music and the first two minutes, which do nothing towards helping getting the transfer belt out. Picking up the pace would raise your like score.
Just get to it already. About half of the time spent in this video was sitting there looking at a printer doing absolutely nothing. Also the music is awful.
Thank you Benjasak, I replaced the "Roller, Secondary Transfer" part# RM2-5906-000 but the line is still coming. i will try to clean the ITB first (part# HP RM2-5907-000CN) and if that does not work then i will order it. it is quite expensive. Thank you for your help.
Thank you for posting this, it was extremely helpful, however unnecessarily long. In order to get more positive comments, I'm providing some feedback to help you and others who view the video after me.
The reason I looked for this video was because my printing was blurry and and there were blank blotches on my print jobs.
Content starts at 1:40, which is way too long. I'd remove the content prior to that and recommend using different music instead of EDM or no music at all. If you don't want to talk on your video, then I'd recommend a text graphic overlay with written instructions. It's hard to see the 2 pieces on either side of the printer that you popped out with the screw driver. I figured it out and set them aside.
At 3:38, provide written graphic instructions on the type of cloth you used to clean the transfer belt. I assumed lint free cloth, however, since I didn't have one, I used Windex Electronic Wipes, which worked well, however, you have to make sure each section dries before you roll the transfer belt forward with your fingers. You rolled the belt forward and wiped it down until 8:54. That's over 5 minutes of watching you roll the transfer belt and clean it. I'd fast forward through this portion on your video.
As I rolled my belt forward, I found the culprit that was making the blank blotches on my print job - a label that was stuck to the transfer belt! I started to try to peel it off with my fingernail, but then stopped because I didn't want to poke a hole in the transfer belt. I found a small plastic tool with a flat edge that was in my computer tool kit. I wet the tip with a little bit of water and gently pushed on the label while it was against the roller (so as to not poke through the belt) and it came right off. I was able to remove the entire label this way. I continued to clean the rest of the transfer belt. There are small white squares on the right hand edge of the transfer belt. I marked one of the squares with a red star so that I knew when I had cleaned the entire belt. You'll notice as you clean the belt and it goes around more than once, it will continue to pick up residue, which is why I made the red star mark so I knew when I completed cleaning the whole belt.
At 10:16, you pop the pieces back in, however, it was hard to figure out how to do it. I finally figured it out in 5 minutes. It would help to have text graphic instructions here as well. You have to put the piece back in with the tab facing toward you and slide it into the notch, then push on the opposite end and it pops back in.
This video could be 3:00 instead of 13:37. However, it did help me with fixing my printer so I didn't have to buy a new one and waste a whole set of OEM cartridges. Thanks so much!
How did you get the small plastic peicws off to pull the tray out? I havnt gotten it yet. Don't wanna brake it
Amazing, I was about to sell off my printer extremely cheap thinking that I couldnt get the stripes that were printing covering my printed pages and after following this video I was able to save it. Thank you so very much for posting this. I love my printer and I had so many extra ink I was dreading selling it.
I did all this and it didn't help mine at all...I'm wondering ..when cleaning the foam bar in the back did you have to keep wiping until it was completely cleaned...mine has a lot of black on it..I was also wondering if the reason mine was doing this is because I am out of color ink and its dumping too much black
Copies on my LaserJet 200 were coming out with just black streaks...thanks for the fix. It took less than 5 minutes to complete the simple task after watching the 14 minute video. Thanks Again!
Is that a regular paper towel that you're cleaning it with?
Thank you for the video. It would be nice to know what type of rag you're using. Is is wet/dry? Is it a cotton cloth? Dry paper towel? Lysol wet wipe?
I absolutely love the music, I would have watched it even if it was longer, very relaxing. This video is exactly what I was looking for, thank you so much! However my belt would not move so I am not sure how to fix this.
A couple of points - the clips that looked easily removed were not, took a bit of force and they pinged off in the end, went back on a lot easier. I had issues with black marks down the side of the documents doing this did help it but not completely resolve it. I just used kitchen towel, I wonder if I needed some sort of cleaner on it? The belt was difficult to move at first and had to be fairly forceful with it. it did get easier after moving it a few times.
Did they break? In am afraid of having no printer.
Hello Sir, i have HP m277dw, and i see black line from top to bottom towards 1/4 on the right side, i opened up the back and saw a roller a greenish spongy roller that has a line about the same place 1/4 on the right side, i think it is the 2nd transfer roller? but i can not remove the line it seem it is embedded into the roller. can i replace this roller my self?
I like the music but wish I could hear you speak so I know what you are talking about. I also don't know what you used to clean the transfer belt.
Very inspiring. Also, I like the music. What is it called?
If I wanted to listen to music, I was going to my iTunes.
sir plz help me, i am in a problem hp laserjet pro 200 color m251
when printer on then one massage on display front door open to continue
I have a blue line down one side of the page which prints even after cleaning, and even when printing in black only. Any ideas?
clean or replace blue tuner.
@@HTF Thank you, that worked!
👍
Yeah, mine was black streaks that wouldn't go away, even after cleaning (with a dry shop cloth).PROBLEM SOLVED when I replaced the black toner cartridge. THANKS!
Couldn't open the front latch. Thank you.
still got lines
Please skip the irritating music and the first two minutes, which do nothing towards helping getting the transfer belt out. Picking up the pace would raise your like score.
What is the problem if you don't clean?
put some light on the subject man .............jeeesssh !!!
I have problem with my printer laserjet 200.... Eror c59.0
Just get to it already. About half of the time spent in this video was sitting there looking at a printer doing absolutely nothing. Also the music is awful.
didnt remember darude sandstorm being this long
Bro. Can't see how you took the clips out. Show that.
how to connect laserjet pro 200 color m251n to mobile?
้Hi you replace HP laser jet pro MFP M177 fw Transfer belt uni ??
Thank you Benjasak, I replaced the "Roller, Secondary Transfer" part# RM2-5906-000 but the line is still coming. i will try to clean the ITB first (part# HP RM2-5907-000CN) and if that does not work then i will order it. it is quite expensive. Thank you for your help.
My wallet and I appreciate you.
Worked well Thank you
Funny part...he didn't even do a "before and after" laser printout comparison. Horrible video.
hp laserjet pro 200 color cómo CORREGIR ERROR DE PUERTA TRASERA SENSOR MALO PARA CERRAR GRACIAS
Reset Chip For Hp Laserjet Pro 200 Color M251 Mfp M276n Mfp ...
Horrible! 13 minute video with ads that could be 2 minutes
Rear door open solutions
Music sucks balls but great video thanks! :)
Worst...