I'm making a plane right now, hand sanding the primary bevel several hours and your video pop up (ring my bell ;)). That is a fantastic simple jig. Cheers!
I suppose that could be fixed by making the angle plate clamp solid at the desired angle. Maybe drill and tap a couple of holes in line with the bolt, near the edges of the angle plate, and install short bolts or set screws that would tighten against the bolt to lock it in place. Maybe switch to the two-eared conduit clamps for added strength. Add a "rip fence" to the plate. Then you should be able to just set the angle and clamp it, and slide the work piece against it while feeding it into the sanding belt until the whole face was ground. You'd probably want to clamp it in different places each time, though, to even out the wear on the belt.
If one thinks heat is a problem, one could use a `Variac Variable Transformer` to decrease the AC voltage, which would lower the speed of the belt (and heat).
![เขามัทรี - เอ็กซ์ ศุภกฤต - จอนนี่มิวสิค [ Official MV ]](http://i.ytimg.com/vi/AS9ufKuQIVs/mqdefault.jpg)
Mr. Young Je, this was just what I needed. I could watch this for hours. Very interesting as usual! Thank you and take care.
It is always a pleasure to watch what your creative mind invents. Looking forward to more awesome ideas!
I'm making a plane right now, hand sanding the primary bevel several hours and your video pop up (ring my bell ;)). That is a fantastic simple jig. Cheers!
It is always nicer to make your own tools over buying them. The pride you get from using them is priceless.
thank you
You always have the best ideas for how to simplify things and still get the results. Great video as always!
thank you
You are a clever and talented man.
Great idea! Thank you for sharing.
Oh, that's very clever! I might have to make one of those. Thanks for sharing.
Brilliant work, my friend! Really well done! 😃
Stay safe there with your family! 🖖😊
Thank you
I hope it's safe
Belle astuce bravo, à bientôt salut Jeannot 😉🛠
After making, what, 30 plus planes, this will be super useful in your shop.
As you sharpen, the angle changes. Check the angle at the end of the sharpening.
of course
I suppose that could be fixed by making the angle plate clamp solid at the desired angle. Maybe drill and tap a couple of holes in line with the bolt, near the edges of the angle plate, and install short bolts or set screws that would tighten against the bolt to lock it in place. Maybe switch to the two-eared conduit clamps for added strength. Add a "rip fence" to the plate. Then you should be able to just set the angle and clamp it, and slide the work piece against it while feeding it into the sanding belt until the whole face was ground. You'd probably want to clamp it in different places each time, though, to even out the wear on the belt.
Straight forward and effective. Very nice.
Wow that’s amazing. Thanks for sharing.
Good ideas there, many thanks.
thank you
Very nice!
Thanks for sharing that
thank you
Beau travail bravo !!
Muito bem feito.
Quanta habilidade...
Maestro Young Je! 🌳✨
Great job will have to try this 👍👍👍👍👍
thank you
WELCOME BACK!!!!!!!
if you flip the jig 180' so the belt grinds away from the bevel (instead of in front) it is easier to see the burr form. Good lookin jig
thank you
Well done, double edged plane blades
This is a test cut,
very clever and useful for many different angles.
thank you
Super! Thumbs up
thank you
Молодец, хорошее устройство.!!!
오늘도 한국의 긍지...빨간목장갑^^ 영상 감사히 봤습니다
감사합니다
super !
Mani d'oro.
Hi TH-cam grandad. Great stuff again. But why do you need a blade sharpened at both ends? Is this part of a new project?
This is a test cut,
👍❤👍❤👍❤👍❤👍❤👍❤❤👍❤👍❤👍❤👍❤
Doesn't that generate too much heat?
It generates heat, but it is not a big problem.
If one thinks heat is a problem, one could use a `Variac Variable Transformer` to decrease the AC voltage, which would lower the speed of the belt (and heat).
👍👍👍
Genius
thank you
Maravilha! Perfeito!
Süper
나무야놀자님..전공이 목공이 아니라..철공이셨던겁니까?
목공입니다~ㅎ 감사합니다~^^
Wouldn't the angle change as the material gets removed?
Of course
Should check frequently
don't you need a support on the other end of the rod to stop flexing ?
I experimented, but I don't need it.
Its so dangerous to work on the grinder in the fabric gloves! Be careful.
thanks
비용은 아주 적고 그 혜택은 백만 달러의 가치가 있습니다!
감사합니다
Very nice!
thank you