He does leave out some key details that could cause some to have trouble afterwards on the air cylinder version. I know from experience. There will be pressure on the regulator side (low pressure side) while you degas by loosening the air cylinder gauge. This could shift/push the regulator up in air cylinder and at very least, misalign the adjustment screw or move it enough where you see the reg body o-ring in the hole which will leak. Just make sure you check it before re-assembly. You can slowly loosen the reg pressure gauge right after the air cylinder begins de-pressurizing to bring them down together slowly so things won’t shift.
Travis, Thanks for this. As I think about it- it looks like the plenum is before the regulator. That doesn't seem to make sense to me. It should be after the regulator should it not?
To Robert: That's not the case in the Dreamline. The plenum is in fact after the regulator. You can check that the regulator adjusting screw that is a part of the regulator assembly body is about 4cm from the reservoir action side. Please, see page 11: fxairguns.com/wp-content/uploads/2019/06/Fx_Dreamline_manual_2019.pdf Regards.
there is a hole with a metal pin in it, below the place where the magazine fits in. If you get behind the metal pin and push it towards the direction of the muzzle it would degas the aircylinder. That is the intendet way of degasing the aircylinder, not by losening the nano meter display.
Travis, I assume that it can be used on the old Streamline too. The tube thread is most likely the same as on the Dreamline. Could you please confirm it fits the SL too? Thank you
Thanks Nice that you explain this all process of power plenum setup. Can you tell me when the FX 9mm impact come to the market. Please ask from some one of FX Company member or John that tell you when the 9mm impact come to the market for purchasing.
Yes. You can increase the plenum volume and thus more efficiency at lower reg pressure. But you will be limited in power gains in .22 and .177 unless you enlarge the transfer port and mod the pellet probe.
let me clarify; actual footage of the fx dreamline power plenum installed with footage of speeds...i have seen the footage of airgun hunters and with jiles when he had the plenum installed on his fx impact mkii
@@jrlayneoliver I was wondering if you meant the dream line lol , I agree with you, I want to see in action 1st...I want a 25 or 30cal 4 hunting hogs,deer,turkeys. racoon...I can get both with fx now that this power plenum is giving there guns more energy...the kalibrigun, or the uragan 30cal is what I'm considering..
i've been holding out for these plenums too; have the dreamline now but am debating between impact mkii especially if fx is going with a .357. i have a texan .457 but looking for something in the middle: if not the fx i am looking at jsar rap...
seems very possible, especially when they have a gun that looks like the wildcat...how is it that the crown & wildcat are late to the party? they may get one,one day
I cant wait mine shipped today be here on Tuesday woohoo! Any word on the dreamline conversation kit for the bullpup to lite? I kinda thought it would be available by now. I can only find the lite to tac kits.
Hi I though lead slinger said the air cylinder was affixed to the block , but it was Jason pesthunter hayes I’m pretty sure it is affixed to the block it’s a non removal air cylinder. Cheers Dean
I would like to see a review of the PCP Beeman chief rifles, they just made updates to the models and have very good comments about their operation and accuracy
What are your thoughts on barrel security with two tiny grub screws holding if in place? For absolute rigidity between scope/action/barrel, I'd like to see the barrel actually threaded into the breech block but it's not possible due to the thin walls of both barrel and shroud. I've noticed this poor barrel location on many airguns.
Pretty cool, if it were in stock. But , I guess it doesn't really matter, since I'm 3 months and counting, waiting for my Dreamtact compact from Fx and AGD.
The whistling is air filling the plenum, I believe all FX rifles with power plenums do this,the MKII Crown and MKIII Wildcat do this which have larger plenums from previous model. I think because your so close to the plenum when shooting it sounds louder than it actually is.
Sorry when a degassed a gun and added a plenum i wasnt able to fill it. Valve is on its place and o rings are new. Whats the problem? Air is coming out from barrel.
Make sure your gun on cocking position ..if the valve not leak you can fill the air..it's no problem if still leaking below 500 psi as long as pressure increase ,valve will close completely..
Just a FYI got my power plenum Sunday! It had the wrong o-ring on it and leaked really bad. So out came the diagram replaced the o-ring with a 23×2.5 NBR 70 and it worked perfectly just a heads up its minor
@@airgundepot it works great to a 24gn .22 slug from 880 to 950 fps and added another 8 or 9 FPE in .25 cal so very worth the money no doubt. Thank you Airgun depot! Thanks for sell great products with great videos!
@@airgundepot will there be any kind of video showing after the power plenum is added? is it accurate at higher velocity, is there a shot count increase or decrease?
Should???? See the fx manual and also the videos that fx do to show you how to maintain your guns they plainly say do not dry fire to release pressure but hey what do they know they only make the guns!
Has no one done a before and after with this power penlum? Everyone talks about buying it but not a single person has tested it to see if it actually works. From what I hear it’s a waste of money unless you’re tuned for serious power and usually in the higher calibers.
Sorry, Travis if I would have read all comments my question would have been answered, NOW will the 380 mm fit on that gun with the 480cc bottle on it as well, I do know it will be close but will it work????
Ww have some on their way, but we have a lot of pre-orders also so it's hard to say. I recommend getting a pre-order in so you can get one as soon as possible. You'll need to contact FX USA too see if you'll need another part to make it work on your compact.
Very well done tutorial! Straight and to the point. I look forward to future Dreamline vids on caliber changes, setup changes, etc.. Keep them coming!
Thanks, we will!
He does leave out some key details that could cause some to have trouble afterwards on the air cylinder version. I know from experience. There will be pressure on the regulator side (low pressure side) while you degas by loosening the air cylinder gauge. This could shift/push the regulator up in air cylinder and at very least, misalign the adjustment screw or move it enough where you see the reg body o-ring in the hole which will leak. Just make sure you check it before re-assembly. You can slowly loosen the reg pressure gauge right after the air cylinder begins de-pressurizing to bring them down together slowly so things won’t shift.
Good points. Bleeding the air very slowly helps with that.
Awesome tutorial Travis. Well done!
Thanks!
Travis, Thanks for this. As I think about it- it looks like the plenum is before the regulator. That doesn't seem to make sense to me. It should be after the regulator should it not?
No, the regulator in the bottle version is in the adapter itself, and in the cylinder, it is in the base of it.
To Robert: That's not the case in the Dreamline. The plenum is in fact after the regulator. You can check that the regulator adjusting screw that is a part of the regulator assembly body is about 4cm from the reservoir action side. Please, see page 11: fxairguns.com/wp-content/uploads/2019/06/Fx_Dreamline_manual_2019.pdf Regards.
there is a hole with a metal pin in it, below the place where the magazine fits in. If you get behind the metal pin and push it towards the direction of the muzzle it would degas the aircylinder. That is the intendet way of degasing the aircylinder, not by losening the nano meter display.
2022 dreamline rifles all come with power plenum installed, and also the fx factory barrel support band at the breech.
What would two power plenums be like screwed together then installed 🤔
We tested that the other day and with certain settings we saw a considerable increase. That video will come out soon.
Airgun Depot can’t wait to see that😉
Travis, I assume that it can be used on the old Streamline too. The tube thread is most likely the same as on the Dreamline. Could you please confirm it fits the SL too? Thank you
I wonder will the Crown get one eventually
that's what I'm hoping to happen
Can we get a follow up to see the gains?
Thanks Nice that you explain this all process of power plenum setup.
Can you tell me when the FX 9mm impact come to the market.
Please ask from some one of FX Company member or John that tell you when the 9mm impact come to the market for purchasing.
Abid Khan It goes into production n Sweden this month - Jon
@@FXAirguns Thanks
Is there a power plenum coming for the Crown?
Any additional benefit adding two instead of one power plenums on the Dreamline?. Thank you.
Depends on the situation, but yes.
@@airgundepot Thank you.
Yes. You can increase the plenum volume and thus more efficiency at lower reg pressure. But you will be limited in power gains in .22 and .177 unless you enlarge the transfer port and mod the pellet probe.
@@arnoldtm31 That's a great point. Thanks so much.
@@arnoldtm31 limited in power gains...so why add the POWER plenum if your limited
Can't wait you guys shipped mine out in today.
Hey Nick, dumb question. what was it listed under on their website? I can't find it.
@@airguns_rc Just type in FX dreamline power plenum In Google and airgun Depot will pop up 4 or5 down.
Did you put it on yet?
Airgun Depot I am waiting for them to fill my order and ship it.
would love to finally see some actual footage of the plenum at work...
Giles airgun gear show and there's another channel, same guys are on matt duber channel shooting dove's with slugs, very accurate and powerful
let me clarify; actual footage of the fx dreamline power plenum installed with footage of speeds...i have seen the footage of airgun hunters and with jiles when he had the plenum installed on his fx impact mkii
@@jrlayneoliver I was wondering if you meant the dream line lol , I agree with you, I want to see in action 1st...I want a 25 or 30cal 4 hunting hogs,deer,turkeys. racoon...I can get both with fx now that this power plenum is giving there guns more energy...the kalibrigun, or the uragan 30cal is what I'm considering..
i've been holding out for these plenums too; have the dreamline now but am debating between impact mkii especially if fx is going with a .357.
i have a texan .457 but looking for something in the middle: if not the fx i am looking at jsar rap...
gerald Williams what would two power plenums screwed together be like 🤔
Will this fit onto the dream-tact compact. The fx with the shroud please ?
Is it possible to apply dreamline's power plenum to the wildcat? It seems quite possible to me.
seems very possible, especially when they have a gun that looks like the wildcat...how is it that the crown & wildcat are late to the party? they may get one,one day
I cant wait mine shipped today be here on Tuesday woohoo! Any word on the dreamline conversation kit for the bullpup to lite? I kinda thought it would be available by now. I can only find the lite to tac kits.
Also a vid of gains in every caliber would be awesome
We hope to be able to do just that in a future video!
Does the aluminum bottle also have a pin in it so you don’t have to degas the bottle?
What did figure out? Do you have to degass it on the other bottle? Thanks
cant wait to get my fx
Very good schooling , wow that was a simple installation , NICE HAT ! !
Thanks Phillip!
Does this Power Plenum work for the FX Dreamline .30cal Tactical?
hello, thanks for your video Travis. does this work on dreamline classic also?
It would be nice if they can do one for the Streamline.
I would bet it's the same for the streamline they are the same parts just different features
@@leadslinger5130 I thought the air chamber was affixed to the block.
Lead slinger you are correct. Cheers Dean
@@pesthunteroutdoors it's not affixed to the block
Hi I though lead slinger said the air cylinder was affixed to the block , but it was Jason pesthunter hayes I’m pretty sure it is affixed to the block it’s a non removal air cylinder. Cheers Dean
Do you know if there'll be a Power Plenum available for the Crown?
Possibly, but it does not lend itself to it. But it is doable.
I would like to see a review of the PCP Beeman chief rifles, they just made updates to the models and have very good comments about their operation and accuracy
We'll try to get to them. Travis has a Chief that is crazy accurate!
Can you repeatedly dry fire the gun to empty the air tube?
If you do that your gun will break
@@roypijnenburg9854 Roy, news to me. What experience are you basing this on?
@@Steve-wz5pz my gun broke
@@roypijnenburg9854 Interesting. I have never heard of that happening. What specifically broke?
@@roypijnenburg9854 Mine didn't.
Nice and Simple. Thanks Travis. What is it listed under on your website. I wasn't able to locate it.
Sorry for the mix-up, it is up now.
Airgun Depot I have one on Pre-order.
What are your thoughts on barrel security with two tiny grub screws holding if in place? For absolute rigidity between scope/action/barrel, I'd like to see the barrel actually threaded into the breech block but it's not possible due to the thin walls of both barrel and shroud. I've noticed this poor barrel location on many airguns.
can this be done with the dreampup bottle ?
Pretty cool, if it were in stock. But , I guess it doesn't really matter, since I'm 3 months and counting, waiting for my Dreamtact compact from Fx and AGD.
Is it all dreamline tact. Bottle came with pin valve in the bottle just like impact?
How would you install the plenum on the Dreamline classic without removing the moderator ?? Can we buy a DFL extension ??
Sal jy ook pro FX streamline maak?
I pre-ordered one on February 20th... Still havent gotten it yet! Totally can't wait to get one for my Dreamline Tactical.
We had more pre-orders than we could fill with our first order, but we have more coming in.
@@airgundepot hopefully soon. Thanks
I have the Dreamline compact tactical I was wondering is this will work on my rifle because the barrel on my rifle is more thickness
It won't. But FX is looking for a soon solution. 👍
Is the shroud removable ? I got my tact coming tomorrow. Longest day ever lol
Rite now r out of stock, when will be available? Cheers
Does anyone know the reason and how to fix the (whizzeling) noise the power plenum makes when a shot is fired?
The whistling is air filling the plenum, I believe all FX rifles with power plenums do this,the MKII Crown and MKIII Wildcat do this which have larger plenums from previous model.
I think because your so close to the plenum when shooting it sounds louder than it actually is.
Sorry when a degassed a gun and added a plenum i wasnt able to fill it. Valve is on its place and o rings are new. Whats the problem? Air is coming out from barrel.
Hello, I have the same issue! How did you resolve it? Thanks!
@@tomparker5000 high pressure blast
@@tomparker5000 connect to scooba, let the air in and shoot the valve will seat on its place
@@kubi1110 thanks, Legend! 👍
Make sure your gun on cocking position ..if the valve not leak you can fill the air..it's no problem if still leaking below 500 psi as long as pressure increase ,valve will close completely..
Is it can fit with FX Wildcat MK2? If it’s fit I want to upgrade my FX WILDCAT MK2 with this power plenum.
What barrel length was that on the bottle dreamline and what length was it on the tube dreamline?
500mm and 600mm
Good job travis
Thanks!
If you fit the plenum yourself will this void your FX 3 warranty?
Just a FYI got my power plenum Sunday! It had the wrong o-ring on it and leaked really bad. So out came the diagram replaced the o-ring with a 23×2.5 NBR 70 and it worked perfectly just a heads up its minor
Interesting, we hadn't anything like that.
@@airgundepot it works great to a 24gn .22 slug from 880 to 950 fps and added another 8 or 9 FPE in .25 cal so very worth the money no doubt. Thank you Airgun depot! Thanks for sell great products with great videos!
hello, do you konw the washers position in a dreamline .22 reg. i have 10 washers
what do you think about Gamo reply 10 magnum in .177 ?
The Swarm Maxxim has been more accurate for us than the Magnum. And the repeating mechanism seems to work better in 22 cal.
hi, could this Plenum be added to the Dreamline Walnut? Tks.
It sure can.
@@airgundepot will there be any kind of video showing after the power plenum is added? is it accurate at higher velocity, is there a shot count increase or decrease?
Is it really OK to dry fire when there is no pressure in the cylinder anymore???
No it isn't
If there is pressure in the plenum you should be fine.
Should????
See the fx manual and also the videos that fx do to show you how to maintain your guns they plainly say do not dry fire to release pressure but hey what do they know they only make the guns!
@@6768lee What they mean is that there is less risk of bending the valve pin if there is pressure behind the valve (pressure in the plenum)
And... do you can fit in dreamtac Compact ?
Unfortunate It doesn't fit the shroud of the compact barrel. But I heard FX is looking a solution now. Maybe soon they will give us the answer. 👍
What about the DreamPup?
Nice air rifle! 👏👏👏 How much? Can ship here in the Philippines? 🇵🇭🙋♂️
No, we can't right now.
@@airgundepot thank you for the information. But how much the price there? God Bless!
Exactly what does this mode do?
It allows for more air to be present in the regulator chamber allowing for more power output per shot.
What Eric said. More regulated air available for more power and efficiency.
thank you
Has no one done a before and after with this power penlum? Everyone talks about buying it but not a single person has tested it to see if it actually works. From what I hear it’s a waste of money unless you’re tuned for serious power and usually in the higher calibers.
@Leon Wilcox
Good to hear! I plan on trying two at once!
Will these plenums fit all bottle guns you think?
Sorry, Travis if I would have read all comments my question would have been answered, NOW will the 380 mm fit on that gun with the 480cc bottle on it as well, I do know it will be close but will it work????
Why you looking at his hands Little Marco Derrick ?
Ooops, 11 mm Allen wrench?
What about putting a Plenum on a dreamline classic?
Does the power plenum just help to improve regulated air efficiency, or does it also help the power or help the accuracy?
Does it fit for edgun l2 ?
You dont dry fire that's wrong info you release excess pressure using the regulator screw dry fire can damage o rings and that is info direct from fx
I like the hat!!
Thanks!
#airguncan
اسوء بندقية استخدمتها واكثر العيوب في الهمر و السبطانه اكس فيها اهتزاز بسبب سماكه ضعيفه السبطان لا انصح فيها
When will these be available. And would this work on the dream tac compact.
Ww have some on their way, but we have a lot of pre-orders also so it's hard to say. I recommend getting a pre-order in so you can get one as soon as possible. You'll need to contact FX USA too see if you'll need another part to make it work on your compact.