At certain point the rock could had just simply pushed over and finished this dicking around, or as the Brits would say cocking about. It’s quite annoying to watch amateurs making something simple into something complicated.
I would install a different tip, more like a flat chisel with an inside curve and possibly a rough serration on the edge. It may not last as long as a pointed tip, but would be much faster to get the crusher up and running at capacity. The pointed tip tends to slip off too much.
There is a reason, why most of the set ups use hooks. Unless the bit placed vertically, it is inherently unstable & can not deliver the force. It is a slow process for such angled applications.
Reading all the comments some of you have no idea how technical it is to operate a rock breaker with breaking it or flicking the spider cap of the crusher
Better solution: Fire the load foreman at the dig site for allowing skip loaders to be loaded with oversized tailings. These boulders should not make it to the trucks until they're first broken up.
The idea is to remove the obstruction...the operator is “breaker” fixated...the first smack got it where it needed to be then he could have just knocked it down in the hole...painful to watch...
At certain point the rock could had just simply pushed over and finished this dicking around, or as the Brits would say cocking about. It’s quite annoying to watch amateurs making something simple into something complicated.
Great idea needs a good operator instead of what is possibly just the manager having a quick go of a new toy
I would install a different tip, more like a flat chisel with an inside curve and possibly a rough serration on the edge. It may not last as long as a pointed tip, but would be much faster to get the crusher up and running at capacity. The pointed tip tends to slip off too much.
I was initially thinking this too , but he probably can’t see anything and relying on someone else’s direction ? Maybe , just a thought
@@nickmeier9356 And camera with dust wiper/washer on boom
Is this the first time the operator used this piece of equipment?
I think that operator is paid hourly?
like watching paint dry..
now there would just have to be someone who can operate the thing properly ^^ : D
It helps if you have a competent operator
Watching this was painful , is the operator on lunch ?
If the hammer had a camera on it, how much time could or would save?
How does this perform with a blunt chisel instead of moil..
They will get better with experience. Crack the nut flip the nut, quick as. Better than the old hook idea, it could only flip the nut.
Better than a crude hook, but still suboptimal here regarding positional actuation.
Perhaps the operator was new?
There is a reason, why most of the set ups use hooks. Unless the bit placed vertically, it is inherently unstable & can not deliver the force. It is a slow process for such angled applications.
It look like a salesman running it trying to get them to pay for the hammer when all they need is a pick on that thing to push it down.
The sharp point is doing them no favors.
Encore un doué !!!!
The guy running that hammer is useless
I read your comment as I’m watching this video and took a sip of pop and almost spit it out laughing so hard 🤣🤣🤣👊🏽👊🏽👊🏽
Ba cái mũi nhọn hàng ngang là xong👍
Reading all the comments some of you have no idea how technical it is to operate a rock breaker with breaking it or flicking the spider cap of the crusher
Ilyen béna gépkezelővel még nem találkoztam!
Must of been a learner operator
That operator did a great job👍👍👍👏🏻👏🏻👏🏻👏🏻
About as efficient as the ol’ analog hook 🤷🏼♂️
It took him 4 minutes to try dislodge the rock rather then break it.
i wonder if this operators parents had any children that survived birth
Пока смотрел, чуть нервный срыв не получил 😡
Better solution: Fire the load foreman at the dig site for allowing skip loaders to be loaded with oversized tailings. These boulders should not make it to the trucks until they're first broken up.
You need a better operator and this will work amazingly
Were is the HOOK?
L'operatore non mi sembra molto capace.
Oh boy…
Those types of hydraulic breakers/hammers always have weak lateral strength. Without straight-line impact they are less than desirable.
So richtig viel Geschick hat der Mann am Specht nicht😢
The idea is to remove the obstruction...the operator is “breaker” fixated...the first smack got it where it needed to be then he could have just knocked it down in the hole...painful to watch...
well there was 6 minutes of incomptence, rather than 30 seconds of work!
Someone is stoned
You have more intelligent than the rock🤯
What a bad operator
Haha operator belajar ini bro
Need a new set up !
This is almost as frustrating as the hook!
هيه خلص مبدعا كل هل قد
👍☘️
complete failure. next time bring someone down who can operate the machine
操作師智商有帶加強 早早就給他撥一下就下去了 還一定要用打的 搞那麽久
Un poco torpe rompiendo la piedra
Rammer hammer breaker..
Ha! Doesn't work! A rock crushing rotating jaw on an excavator arm could both retrieve and crush big rocks!
Your fired.
Oida! A so deppert ogschdoin! Der braucht doch des Ding bloß rübadran dann foids aloa nei!
the hook is better
เปลี่ยนคนเจาะ
bisognerebbe mettere escavatoristi bravi non come questo
Я дал бы орден за тупость .
Ohh for Christ sake just spin it with the hammer and push it in jesus
Бездарь! Близко к установке пускать нельзя.
Poor operator skills.
Cambia operatore che questo nn ce buono nulla
Tem bicho ruim.
This is frustrating to watch as an operator. No skill no vision
Worst operator ever seen🤦♂️🤦♂️🤦♂️
כבר אני סבל שעה3 עבוד 😬😬😡
אבן גדול גרם סבל
לילה עבוד סבל ☝בוכה זרק
долго до тупого доходило, что его надо было сдвинуть