ARDUINO PROMINI - HOW TO UPLOAD CODE
ฝัง
- เผยแพร่เมื่อ 13 พ.ค. 2017
- This video describes how to upload code on to Arduino PROMINI
USB-TTL board is used to upload code.Also your UNO board can be used for this purpose.
alselectro.wordpress.com/2017... - แนวปฏิบัติและการใช้ชีวิต
Uploading from a UNO was new for me. Great video. Thank you.
Very good tutorial - saved me a lot of hair - I had been pulling mine out! Thank you so much
Very clear, detailed and to the point. Thank you.
DTR is the same as GRJ.. You helped me so much. That is the only way i could get my pro mini configured. You Rock!!!!
Thanks for your video! Just had wrong uploads all the time until I noticed I had to switch the board to "Arduino Pro or Pro Mini" Instead if "Arduino Mini" !
Thank you...THANK YOU!! i have been scratching my head over doing this and failing. i was Tx to Tx and Rx to Rx. You fixed my issue!
absolutely Magic, simple and to the point, thank you
Thank you. Saravanan very detailed guide.,useful info & important for beginner like us ready help me a lot. Appreciated
Thank you so much. I really appreciate this tutorial. Keep up the good work !
Thank you, with your tutorial i programmed my mini pro clone...
Thanks dude, I was not clicking the reset button! :D
Zwięźle i szczegółowo. Dziękuję.
thank you , the best video that solved my stupid problem with old promini
Thanks so much , clear and to the point !
best tutorial about this topic
Thank you. Your advice help me solve this problem.(press reset switch when show uploading)
Thanks , I got my pro mini life again.
Many thanks for the good explanation..
Bundle of Thanks brother... you solved my issue... May live long and happy life.. :)
You're a miracle, Sir.
still a very helpful video. Thank you again!!
this video is great ! thank you sir
This is a very good tutorial, I have just liked and subscribed. Thank you... :)
ممتاز.. شرح وافي ، ويظهر أنه خبير.
Good examples learned thanks.
Thanks man, works great!
Thanks! I did not fry my Pro Mini board!
Thanks really helpful!
Very good explenation sir
thank you sir solved my problem
i had connected rx to rx
tx to tx
Bro please help me
me too!
useful tutorial sir,
Can 3V 8 mhz pro mini connect with usb ttl dongle with 5v input?
thank you sir
Thank you!!!
Sir which is best good TTL board for. Purchase
Can I upload the program to mega using this device?
Sir, What is the baud rate of CP2102?
Hi! I'm the small guy who came to your shop to buy Raspberry pi , Arduino etc. You remember?
Very useful
Thanks a lot!!
whit TTL is posible to conect and disconnect to upload ?
it works
Thank you :)
I have doubt 'what is vin pin in Arduino pro mini?
thank you
Thankkkkkk you
it's the best time to open your own online shop for electronics. think on that.
Sir in cp2102 3v3 where it can be connected in Arduino pro mini plz tell me very fast
Why usbasp programmer when you did note się but ftdi?
We need to install driver or not. If we need to install. Please tell which driver I need to use
no we need not install driver
thaaaaaaaaaaaaaaaaaaaaaaaaaank you sooooo much
dayıcığım senin taşaklarını gezdirenler yesin... adamsın. çok iyi bir insansın.
Sir please help me. I'm trying to upload code to arduino pro mini using cp2102usb to ttl. Converter for an year but it shows error in uploading. It shows programmer is not responding. Pls give me ur number
why didn't I see this before I pulled my hair lol
My cp2102 converter show serial port properly but don't work
Please help
The solution : a 100nF capacitor in series on the DTR pin.
Now, you don't need to press the button.
----------
La solution : un condensateur de 100nF en série sur la pin DTR.
Maintenant, plus besoin d'appuyer sur le bouton reset.
Hi
Can you please help me on something iof you have 5 minutes?
I have? a 5 volt Pro mini(16mhz) and works nice on a blink scetch.
But the problem is that when i power to RAW pin from batteries (8x1.2=~10 volts)
Vcc pin has only 3.3 volts.
Some men form arduino forum told me to check the F_CPU and
Serial.println(F_CPU) outputs 16.000.000 (16 mhz)
Also the regulator says S2RA that i found somewhere that is 3.3 volt.
...but i bough it for 5 volt not 3.3 !
You can see in the forum the picture that shows my arduino is like the 5 volt that you are using in this video.
forum.arduino.cc/index.php?topic=711660.0
Can you check please your 5 volt arduino if it gives 5 volt or 3.3 vcc
when you have 5 minutes?
(To avoid order onother that will have the same problem?)
Tes bon
please call me
thank you