RFID Programming Guide
ฝัง
- เผยแพร่เมื่อ 26 ม.ค. 2016
- ** EDIT **
Managed to find a copy of the instructions and uploaded here. Enjoy!!
www.yorkshireautomation.co.uk/...
This is a short video describing how to programme the RFID keypads in preparation for inclusion in a Z-Wave system. Visit www.yorkshireautomation.co.uk or just email me info@yorkshireautomation.co.uk for more information.
If you enjoy watching these videos then please show your appreciation by making a small donation:
www.paypal.com/paypalme/yorks...
Many Thanks
Thank you for taking the time to make and share this. There's a funny, benign background to this story, but the short version is that with this video and a Cyrillic instruction manual I now control access to a 20+ apartment building in Eastern Europe.
Thanks to share this information. Great job!!!! Once again thankssssssss
Great video. Thanks
Great job .. thanks ...
Excellent
Anyone that uses this RFID system shown is asking to have whatever it protects access to, accessed, you might as well put a key under a plant pot. All the control on the back, easily accessible to anyone who levers it off the wall.
Not quite. The keypad in my scenario is designed for indoor use. Unless you know which wires to short out you won't disarm the alarm.
This video is only to demo the turning on/off of an alarm system and not door entry system.
Qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq
I added a new RFID Keyless Tags with the same frequency so both old and new tags are working. I was able to open the door using those tags but it never goes back to lock mode itself. It usually goes to lock mode after a few seconds. Instead I have to de-energize the unit so it will lock again.
Also, adding a tag number 2 doesn't work I used the number "5" instead. We have the same RFID Controller but I don't know why the difference. Your feedback is highly appreciated. Thanks!!!
Thanks for your message.
I have posted the instruction manual in the description. Best is to read that. I'm not an expert in these keypad but was demonstrating how to integrate with fibaro in that video. Unfortunately I don't know the advanced details for this device.
Only thing I can suggest re lock issue is to check the 'auto lock' time settings
We have this unit and everything works great. However, when I purchased extra FOBS, they can't be programmed! How can I ensure I am getting the correct FOBS when I order additional ones? As it turned out, the new ones are larger, but thinner than the original ones that came with the unit.
Hi,
im sorry i dont really know as i use the keyfobs that came with the unit. also i only use this in the z-wave modified version as part of my home security system.
psutisfifsifsifis
Hi. Anyone know how can I buy the replacement sticker for this model?
Hello...
I want to know something about this device...
Can we attach electric gate lock with this?
Yes
Hello, please could you tell me how to change the time between door unlock and lock, because I have an equal device, but its time is 1 minute, it is a long time waiting for the door to lock again, and the LED is red again. thank you very much
hi. according to manual i have this is what you do:
'*' then 'your password for config' then '#' then '3' then '2 numbers for your new time eg 10 for 10 secs' then '#' then '*' to finish. this would change your unlock to lock time to 10 secs.
hope this helps
Could you tell us some more about what power source you are using?
Robin Kaiser
I am using this keypad as a home automation alarm keypad. So I have a basic 12v 2A power supply
Thanks m8 :)
Idol pwede din bang nag set up ng card kahit hindi mo na babaguhain ang lock code at system code?
if mode blink continuously, what is problem?
Hello. Can you please tell me, if this device can be used like timed locker? i mean from morning like 7am to 8pm it would be unlocked and from night till morning should be locked. Is it possible? thanks for an answer.
MultiDreamer21
No I'm afraid that this lock doesn't support that.
maybe can you tell me which china made device can do this? i mean, i can connect different type of rfid box reader to lock and power cable. i think.
you can buy a power supply timer used for sprinkles or Christmas lights. they are around $10
yeah i was thinking about it, thanks.
Im sorry guys, i only modded this device to use as part of my home automation security keypad. i dont use this for its intended purpose as a door lock and therefore dont know much about that side.
Hi, My AD200-M, does not have a reset button on the board but it has the jumper, Pin1,2,3. to reset it do i have to jump pin 2 &3 and continue following your resetting instructions by powering the device till you hear the bleep?
to be honest im not sure mate
@@YorkshireAutomationThanks i found a PDF catalogue online, posted on my previous post
Hi, could you help me? When I try and add a tag it continuously beeps. Not sure what I'm doing wrong
Hi
I'm sorry I dont know too much about this keypad as I was only modifying for smart home use.
I would try and reset the keypad and start again. Failing that get in touch with the manufacturer.
Thanks
Did the manufacture code is fungction for all type of acces control?
No. Each panel is different
Hi, i have the same device, but I need the explication in spanish or a user manual in pdf. Would you mind helping me ??
Sorry I don't have pdf anymore
Hi I have a question. What will hapen if the electricity stop. Is the locker automaticly unlocked?
I'm sorry I don't know as I have modified the keypad to use as an alarm keypad in a fibaro home automation setup
Tnx anyway. HNY!
ivozax unfortunately it does :( .. So manual door lock is needed for it. Possibly got another method how to not unlock when no power, dont know how for now..
Hellped Heaps thanks Ross NZ
hello, can yo tell me please, how modify delayed time to open de door, ? thank you.
Hi
I'm.sorry I dont have instructions anymore for this model
Is there a way to remotely deactivate a “lost/stole” FOB? Or how can one secure the lock from this rogue FOB?
Hi
The only way to remove a fob is to swipe it after entering 'remove fob mode'. If you haven't got the fob then the only other way is to remove all fobs and re add the individual fobs back in.
Hi..Brother! Do you have any show about Sebury UReader-D ?
Thanks.
I'm sorry I don't
THERE IS SOME GOOD INFORMATION IN THIS VIDEO - HOWEVER IF YOU TOOK SOME TIME TO EDIT THE GAPS - WHEN YOUR TRYING TO THINK OF SOME INFO, IT WOULD MAKE THE VIDEO MORE EFFECTIvE. THANK YOU FOR THE VIDEO EITHER WAY :D
Chill
my red led isn't blinking at power up. subsequently it's not allowing me to program it.
please check the power supply to see if you have power. also could be a faulty keypad
christopher ayarza me either
I tried a factory reset but now my keyboard is in a constant solid beep and will not stop or reset!! Nothing seems to help even with a power disconnect button reset. Help !!!
Hi
If the factory reset doesn't work then that indicates there could be a fault with the keypad.
im install a rfid like that. but when i put the power direct to the power socket. it only beeps, red light only. is that normal??? i hope u can help me. thanks.
The same to me ? Did you find any solution?
When hash key is pressed nothing happens what might be the problem
Hello,
I have same with troubleshooting all light are on when i power ON , light Power ,Ok and modes all toghter ON when i power supply is ON.
try reset. otherwise could be an issue with the keypad
I recorded the same code for programming
and the opening of the door. when I start recording a card I start by entering the programming code. but I always listen to a signal and the door opens and the programming does not start. is there a solution
yes, and that is to reset. you cannot have the same codes
We are moving into a warehouse that has one of these. I do not know the management code. How do I reset it not knowing the current one so that I can use it?
Hi
There is a link at the beginning of the description to the manual.
That will let you know how to reset it
can i install one of these on four different doors and use the same pass codes and tags to open doors?
Yes u can
@@murtazarafi can you tell me how to use the same tags with the four controllers
you just add the same tag to all 4 keypads and set the same codes when you are programming the keypad
What if you lose the tags?
My controller is not giving beeps at all. Please suggest how to activate buzzer
Hi. I'm sorry I don't know how to do that.
Can u program 2 doors with 2 of these units to share key phobs or is it one phob per unit
hi
you can have 1 key fob and program them for 2 different units
hi..if we reset the code, will the tag also be reset?
Yes as it resets the whole thing
My key pad is alarming and can not clear it but can use my passcode to enter but not key fob?
It means that the keyfob hasn't been programed in correctly. Need to do again
how to increase time of opening door ? it is too quick to get lock before someone comes in
Hi
Download the manual from the description. It will say in there how to increase. Thanks
what is this universal sensor you refer to ?
Back in 2016 it was a Universal Binary Sensor. Now they have been superceded by Smart Implant
hey pls help me fbd-006 access controller user guide give me?
sorry dont know that one
How can i convert this device to anti copy device , 😊
I have the same I powered it and it makes a continius sound .How can this stop!
Try and do a factory reset
Hi what do I do if I can’t remember what’s the factory password?
Use the link above in the description to download the manual and factory reset the keypad
D0 D1 for what ?
Its not working to my doorlock. The management mode with * and # its not working
Try resetting the keypad. The instructions are on the download link
the red light is solid.
in some models the red light is solid. in some it flashes. i have both types. if nothing happens on keypresses then try resetting the keypad. there is a jumper on the circuit board. see instructions on how to reset. failing that contact where you bought from. thanks
how to remove the master card assignment I've assigned bunch of master card
You will have to reset I'm afraid
What is the model number of this system???
The keypad is a generic keypad, but the home Automation system I use with it is a fibaro system
How about if you wnt to add a new pin password
its in the video mate
@0:58 standard mode
@1:05 bell button / alarm
@2:37 factory default / changing admin-code
@4:00 register key-fobs to unlock
@6:05 register keypad-code to unlock
@7:40 delete tags / codes
@9:12 FULL RESET
@10:16 conclusion
Źz,
Gyghhhhhguuuuuuuuu
How can i turn it off
Mine keeps making high pitch sound non stop, anyone know how to fix it?
Mine too ? Do you have any clues!
@@user-gi5tj3yg4g I dont remember what I had done, I think it was something with the connectors inside or turning it off and on again...
my door lock opens automatically after power supply goes off and on.
Can you help me please?
Download the manual from the link in the description to change the parameter settings
@@YorkshireAutomation Not able to find. Can you help me please?
@@replay.gaming www.yorkshireautomation.co.uk/downloads/RFIDmanual.jpg
Thank you for the pdf.
I switches to NC port but now the gate is just opposite.
When i enter passcode it closes and after 5 sec it opens.
Do i need to change any other wires?
@@replay.gaming I think a change in wiring is required for that
Is it for human implants as well
? You can use the fibaro smart implant and still use the same wires
Same wires?
Human implants?
Yes is it correct to use for human implants as well
You can attach any device with this with the appropriate hardware
When i press the star button it does not light green why?
try resetting the keypad. or it could be a faulty keypad
@@YorkshireAutomation done 👍 thank you 😊
This is the equivalent of using a padlock made if wood instead of metal. Any crook can just shirt out all the cables and open the door
How to delete everything to factory settings?
there should be a jumper setting or pins which you short out to reset to factory. see link in description for the manual
My pad doesnt have a star button
same here, from outside its there, but when opened to check nothing down the button, is it a malfunction device?any help? email: hussbarada@gmail.com
Waterproof?
No
is it possible can you reset just one task?
as far as i know you have to reset the whole keypad. you cannot reset 1 element
How to change public open pin ?
in the EDIT section i have posted an image of the instructions
that will show you how to change pin
HOW MANY TIMES PASSWORD CHANGE IN THIS SYSTEM SIR PLS TELL ME🙏
You can change the password as many times as you like.
I don't believe there is a limit
Hi, how to change the passcode?
In the description is the link to the instruction manual. Use that to change the passcode
Can you just delete 1 tag and not all
From memory I believe you can. I will need to check. I'm away at the moment and will update when I get back next week.
@@YorkshireAutomation To delete individual cards watch this video th-cam.com/video/rr4Cmi5ad0g/w-d-xo.html
How to change passwords to open door
take a look at this:
www.yorkshireautomation.co.uk/downloads/RFIDmanual.jpg
And how to hack the rfid implant and set new password.
I think I have already shown how to factory reset. Unfortunately I dont have instructions any more for this keypad
Assa Abloy aperio mortis wiring diagram
wiring diagram for what please?
Where is J2?
Only Legends use RFiD access control for Safety. Saya dah pernah install dekat toilet. Puas hati member nak pakai kena bayar rm1.
Yupt