In this episode of CTPTV you will learn how to replace the rear crankshaft seal on a 3306 Engine. En este episodio de CTPTV aprenderá cómo reemplazar el sello trasero del cigüeñal en un motor 3306.
You cleaned all the oil off the crank and then applied the retaining compound which looked like a green sleeve retaining lock tight but then you did something that was counter productive. You applied oil to the inner part of the sleeve before installing. if your going to oil it then why clean the oil from the crank and why install the retaining compound? The retaining compound won't work if there is oil between the sleeve and the crank.
The flywheel has one offset bolt hole because there isa 3/8 nc bolt hole on the front face of it for locating #1 or #6 TDC. This has nothing to do with balancing anything..The flywheel can only be installed in one position on the crankshaft flange.
Have chenged sump gasket and a bell housing gasket and a rear seal for a 500kva scania engine and my funny story is the engine cracks but doesn't run. Gone ahead and changed flywheel sensor ,nothing is going on. Help me.
Hello and thank you for contacting us. For any questions or inquiries, please email us directly at marketing@costex.com so that one of our representatives can better assist you. Thank you!
Hello, thank you for watching our video. No, you do not have to drain the oil before taking the seal out. The oil level should be below the seal. If you have any further questions, please do not hesitate to contact us.
Although it is not necessary to drain the oil for this procedure, we at Costex agree with Michael Fawcett’s answer, since it is always a good idea when servicing an engine, to do a complete oil and filter change. Click here for a listing of oil filters Costex has available for your engine www.costex.com/Library/inserts/F-720-031.pdf .
Thank you for watching our video. Feel free to give us any suggestions for more videos that you would like to see. We are always looking for feedback from our viewers.
Yes, for the NPR engine you need to remove the transmission. www.ebay.com/itm/Oil-Seal-Crankshaft-Rear-For-ISUZU-NPR-NQR-4BD2-3-9L/152127914551?epid=1873603663&fits=Make%3AIsuzu&hash=item236b87c237%3Ag%3AZAoAAOSwMNxXXvFe
Thank you for watching our video. We are glad you enjoyed it. Feel free to give us any suggestions for more videos that you would like to see. We are always looking for feedback from our viewers.
Thanks costex , these information on how to properly taking care of diesel engine mighty useful. Thank you guys very much.
Thank you for the comment!! Glad we could help :)
Use retaining compound and then oil the mating surface? Doesn't make sense
Why would you put a retaining compound on the crank surface then oil on the wear sleeve surface where it contacts the crank
No kidding?!?
You cleaned all the oil off the crank and then applied the retaining compound which looked like a green sleeve retaining lock tight but then you did something that was counter productive. You applied oil to the inner part of the sleeve before installing. if your going to oil it then why clean the oil from the crank and why install the retaining compound? The retaining compound won't work if there is oil between the sleeve and the crank.
Love these tech videos.so not like real life in shop.looks so easy.lol
What’s the easiest way to take the seal out of the machine, is it better to remove the whole engine or drop trans? Can I get some info please
The flywheel has one offset bolt hole because there isa 3/8 nc bolt hole on the front face of it for locating #1 or #6 TDC. This has nothing to do with balancing anything..The flywheel can only be installed in one position on the crankshaft flange.
Mine has a dowel pin.
Some flywheels have weights to help balance the engine. I'm not sure if caterpillar is doing it but I know GM has been doing it for about 40 years.
Please what is the name of the installation to 500 KV the size of number please
I need it too size or the number
Thank's very helpful
Thank you for your comment!
Where can I find the front and rear Installer?
Do you guys sale the installation tool?
Azz.....stringe i bulloni sull' albero motore con una pistola pneumatica? BRAVO'
How much it cost for parts and labor?
Thanks for share the video :))
Have chenged sump gasket and a bell housing gasket and a rear seal for a 500kva scania engine and my funny story is the engine cracks but doesn't run. Gone ahead and changed flywheel sensor ,nothing is going on. Help me.
Hello and thank you for contacting us. For any questions or inquiries, please email us directly at marketing@costex.com so that one of our representatives can better assist you. Thank you!
Do u drain the oil before taking the seal out?
Hello, thank you for watching our video.
No, you do not have to drain the oil before taking the seal out. The oil level should be below the seal. If you have any further questions, please do not hesitate to contact us.
YES ALL WAYS DRAIN THE OIL WITH NEW OIL & REPLACE THE OIL FILTER AS WELL
Although it is not necessary to drain the oil for this procedure, we at Costex agree with Michael Fawcett’s answer, since it is always a good idea when servicing an engine, to do a complete oil and filter change.
Click here for a listing of oil filters Costex has available for your engine www.costex.com/Library/inserts/F-720-031.pdf .
u need to pull out the gearbox + the clutch for change this seal... so made it when servicing ? :/
Can you apply Grease instead of oil on the seal before installing
Thanks
Hi is it possible you can sell me one of those tools
Nice
Good sir thanks
Anyone know if the seal installation tool for a c13 is the same as a C15?
He did say 3406. So I’m guessing any variant.
@@diegomurillo2194 *3306*
nice video short and to the point
Thank you for watching our video. Feel free to give us any suggestions for more videos that you would like to see. We are always looking for feedback from our viewers.
you are great
does the transmission always have to be removed no matter what make or model? I am replacing the rear main seal on a Isuzu NPR DIESEL
Yes, for the NPR engine you need to remove the transmission. www.ebay.com/itm/Oil-Seal-Crankshaft-Rear-For-ISUZU-NPR-NQR-4BD2-3-9L/152127914551?epid=1873603663&fits=Make%3AIsuzu&hash=item236b87c237%3Ag%3AZAoAAOSwMNxXXvFe
Hello! Always, there is no way to get to the seal if the transmission or engine is not removed.
no need to remove the transmission, instead you remove the engine.
@@dannyyo7948 lol
Can I double the rear oil seal
dam just bought that installation tool from cat 300 bucks, great video thanks.
Thank you for watching our video. We are glad you enjoyed it. Feel free to give us any suggestions for more videos that you would like to see. We are always looking for feedback from our viewers.