@@FacilityD20 www.amazon.ca/EEFUN-purposed-Silicone-Squeegee-installation/dp/B076FT2MJ3/ref=mp_s_a_1_18?dchild=1&keywords=silicone+squeegee&qid=1625701575&sprefix=silicone+sq&sr=8-18 These are the ones I use but unfortunately they aren't in stock atm.... They cut in half really easy for small vats like my MARS.
@@FacilityD20 I kindly suggest to DO IT as @Matt Collins suggest. 2nd time ever i use my new printer i badly scratched the surface with the plastic squeegee. it's still usable i think (im less than amauter) but im considering to buy a spare just in case.
I leave resin in for months and just stir before use. Only time I clean the vat is after a failed print and to do that I get a cured piece of support and raft and place it in a corner of the vat in the resin then hit the tank clean function 2x 30 seconds to cure a bottom later in the vat. The slowly tug on the support to loosen the cured resin mat out of the vat which removes all failed print blobs. No scraping or washing = FEP lives longer.
Just did my first resin print last night. And didn't know about the ptfe lubricant thing, and omg I could hear the print peeling from the the ptfe sheet all night from behind 2 doors, it was so loud 🤣🤣
Very good info for the beginners, great work my friend. And if you don't mind me saying, this process is pretty much the same for water washable resin as well.
@@FacilityD20 why did you bother with alcohol then? :D it would have been good to make that clear maybe - alcohol is what causes all the smells and that can put a lot of people off resin printing but if you use water washable the environmental issues are almost all resolved :)
@@BeardClipper I find it gets any stuck partials off. I only use it when I don't plan on filling the vat back up for a while. I don't mind the smell of alcohol, but the small of the resin is a little more annoying for me.
been printing since last summer, only changed FEP once and that was because I used IPA to clean it, it made FEP cloudy. Now I've been using built in tank cleaner and it works, but right now after I inspected FEP it had a bit cloudiness in it, but not too bad, probably from tank cleaning since I have to push it from the others side (yes, I wear nitrile gloves), might gonna start using the support technique everyone is talking about, so I don't have to use my fingers to remove resin sheet after cleaning.. we'll see what happens after this current print.
Needing a fep lube means your exposure times are off, all you're doing is using a crutch when you could just tune your printer in. That stuff contaminates resin fast.
I had a buddy give me grief for aerosol lube, I had the same can and all. told me to avoid a can and use those mini superlube sticks. In your humble opinion, does it even matter?
For me I have noticed a difference, I also noticed that if I have a failed print stuck to the fep it seems to come off easier. For me it's worth the few seconds it takes to apply it.
okay so all throughout the video you were VERY insistent on never getting resin on the screen, i have a screen protector on it, but i think my FEP screen wasnt fitted properly so resin leaked all over the screen protector. ive ordered a new FEP cause i was an idiot and ruined it on my first try, but should i order a new screen protector aswell and thoroughly clean everything?
Helpful video - thanks! Just curious, how long can I leave un-used resin in the vat for? Would love if I didn't have to syphon and clean after every print (just bought one, total newbie). Thanks!
when i had a resin printer, i noticed the film started to get a foggy look. think it may came from the alcohol. i used Isopropanol . did i use the wrong alcohol? will it affect the print? uv light not getting through is?
my vat is definitely scratched totally hell and I been scraping away with the spatula that came with the printer and now none of my prints been sticking smh
Many manufactures had warned about using the plastic spatula on the FEP film. Please use a silicone spatula instead. The less scratches, the easier it is for prints to not get suck to the film and break off from supports.
Fill it up a little with IPA let is soak, try to rub the back of it with your hands and gently try to pick it off. If it is really bad you might have to replace the fep
If your printer has a vat cleaning option, use it. If not, try running the LCD test for like 30 seconds and then just release the cured film on the vat. It will also take out the cured resin there. You can also use old cured supports from a previous print and put it in one corner and do the LCD test or cure option. Take out the vat and carefully push from beneath the vat with your fingers (not your nails) to release the film from the fep, then you just pull the old support and the film will release with it. Fep clean and good as new.
So Iv got a question for anyone here I got one from a friend and this guy gave it to me and let’s just say it went everywhere down in side of my machine does anyone have a recommendation? On how to clean this or is it trash? I don’t know please can someone help me
Try using some IPA to clean it off. If it's not on the light, and you can't clean it, put it outside and just let it cure in the sun onto the machine. All my peinter are getting full of resin too.
Never put any cloth on your FEP. Empty the vat. Do a tank clean, remove the cured layer, squeegee what's left with a silicone spatula and wipe the vat only.
@kevinlee358 I agree, but so far, for me wear and tear from Printing minis and the occasional stuck print, has damaged all my fep before a lint free cloth has so far. Also dropped my magnetic build plate in there once and it cut a hole...
this is not what to do, newer resin printer have a cleaning mode, that will solidify the first few layers and you can use a old support to pull out the sheet of resin.
Ahh man you waste a lot of resin there; you can scrape all that into the bottle man; not onto the towel :) other than that, yeah cool tips :) Edited to add - why did you scrape the resin while the vat was still on the screen; that's a really bad idea dude; if there was a weak FEP, or something that could pierce the FEP, then doing that would directly cause a spillage (never mind what others have observed about the fact that you did cause a splash that could also cause issues)...
Yeah, I wasted a bit more then normal, I blame the camera set up, I could have saved more resin for sure. There are two reasons I rubbed the bottom of the vat while in the machine: 1. to quickly check what kind of condition the resin was in, cause it was left a long time, but it had started to coagulate on the bottom, which lead me to rub it more out of curiosity haha) 2. The spill was on purpose, because I wanted to talk about and show cleaning it because of the potential issue it could cause. (I could have edited that bit out). So it was about 80% intentional and %20 curiosity hahaha.
@@FacilityD20 Yeah I just really don't think encouraging people to do that is a good idea; you could damage the fep, then the resin goes onto the screen and you have to scrape it off (ask me about that :D hah) Cheers mate,and congrats on the channel success!!
You can use a hair dry air with cautious moderation , into it melt the resin for very easier removal. In combination with the yellow tool to help detach the stuck resin in the FEP or in LCD screen ,that makes them look dirty. after 5 minutes or so with the hair drier , on top of the resin you can detach the resin entirely , leave in one piece and if it was pancake and it will take from the FEB or LCD 99.8% of the resin . After that Handywipes or microfiber cloth for the final touches.
I'd honestly recommend only using silicone/rubber squeegee to scrape the resin out. Even the plastic ones will scratch and degrade the fep over time.
I will pick one up
@@FacilityD20 www.amazon.ca/EEFUN-purposed-Silicone-Squeegee-installation/dp/B076FT2MJ3/ref=mp_s_a_1_18?dchild=1&keywords=silicone+squeegee&qid=1625701575&sprefix=silicone+sq&sr=8-18
These are the ones I use but unfortunately they aren't in stock atm.... They cut in half really easy for small vats like my MARS.
@@FacilityD20 I kindly suggest to DO IT as @Matt Collins suggest. 2nd time ever i use my new printer i badly scratched the surface with the plastic squeegee. it's still usable i think (im less than amauter) but im considering to buy a spare just in case.
I leave resin in for months and just stir before use. Only time I clean the vat is after a failed print and to do that I get a cured piece of support and raft and place it in a corner of the vat in the resin then hit the tank clean function 2x 30 seconds to cure a bottom later in the vat. The slowly tug on the support to loosen the cured resin mat out of the vat which removes all failed print blobs.
No scraping or washing = FEP lives longer.
For sure! That will work
good idea about using a cured support piece
Just did my first resin print last night. And didn't know about the ptfe lubricant thing, and omg I could hear the print peeling from the the ptfe sheet all night from behind 2 doors, it was so loud 🤣🤣
That is a good sound it means it working! haha
@@FacilityD20 yeah first print came out surprisingly good. I just want expecting it to be so loud 🤣🤣
suddenly all makes sense... the filters kinda confused me at first sight of my new printer lol
great vid
Thank you
Honestly amazing video , the basics here are so important and honestly can prevent costly mistakes tytyty
Thanks.
Very good info for the beginners, great work my friend. And if you don't mind me saying, this process is pretty much the same for water washable resin as well.
Yes, that is what I had in there I this video.
@@FacilityD20 why did you bother with alcohol then? :D it would have been good to make that clear maybe - alcohol is what causes all the smells and that can put a lot of people off resin printing but if you use water washable the environmental issues are almost all resolved :)
@@BeardClipper I find it gets any stuck partials off. I only use it when I don't plan on filling the vat back up for a while. I don't mind the smell of alcohol, but the small of the resin is a little more annoying for me.
Just grabbed my first printer, great video Troy
Thanks. If you have any questions just msg me.
Which printer did you get
@@stephon972 I grabbed a HALOT one by Creality... loved it so far, some crispy prints and super easy to use
Sweet video, thanks for posting! Enroute to learning how to make rings to cast.
Glad it was helpful!
been printing since last summer, only changed FEP once and that was because I used IPA to clean it, it made FEP cloudy. Now I've been using built in tank cleaner and it works, but right now after I inspected FEP it had a bit cloudiness in it, but not too bad, probably from tank cleaning since I have to push it from the others side (yes, I wear nitrile gloves), might gonna start using the support technique everyone is talking about, so I don't have to use my fingers to remove resin sheet after cleaning.. we'll see what happens after this current print.
I agree i am hesitant to use the self cleaning myself
Honestly I just use a paper towel and I've never had a problem after years of resin printing.
Can be a bit hard on the FEP but it will work
Just bought my first printer. This video was very informative. You must be from nfld!
That is awesome. Yes i am from Newfoundland.
@FacilityD20 I thought so, I'm in nb but I've got family in nfld.
Needing a fep lube means your exposure times are off, all you're doing is using a crutch when you could just tune your printer in. That stuff contaminates resin fast.
exposure can be hard to lock down that is for sure.
Idk what any of this means but cool beans.
That's cool.
What do you do with the cloth once you’re done?
Throw it away
Before throw away, lay those cloth at flat and use UV light devices or at sunlight to cure "wet" resin inside cloth.
Excellent thanks
You are welcome
Thank you for the video.
You're welcome
Is it the same method with water based resin?
Yes
I had a buddy give me grief for aerosol lube, I had the same can and all. told me to avoid a can and use those mini superlube sticks.
In your humble opinion, does it even matter?
For me I have noticed a difference, I also noticed that if I have a failed print stuck to the fep it seems to come off easier. For me it's worth the few seconds it takes to apply it.
Well, my vat is covered in hardened resin, because I was an idiot. Is there a way to get it off, or so I just see how long it lasts?
Not sure.... sorry
I didn’t realise you can leave your resin in the vat for 3 weeks!
I have left it for a lot longer lol
So I´m about to buy a resin printer and i see i can leave the resin in the vat for sometime without issues?
Yes, i have left if for like 6 weeks before
Once were aligator hunter now 3D printer man - troy , swamp people
I don't know what you are talking about but I like this comment.
@@FacilityD20 haha sorry you resembled a clean-cut troy from the show "swamp people" haha
@@UnitBeerMonsta I'm going to have to check it out haha
Only issue I would advise against is cleaning the FEP with Iso Alc. It might leave a foggy finish on FEP
After a while yes, so far mine has always gotten damage from printing before that issue for whatever reason,
Great info. Thanks for sharing. How often should you clean the VAT?
Not that often I only do it after fails now
Curious what brand of shop towel you have in this video. Can't seem to find them anywhere.
Just what i found at the hardware store. Nothing special, i look for lint free.
We're can I get some of those tows
Hardware store
okay so all throughout the video you were VERY insistent on never getting resin on the screen, i have a screen protector on it, but i think my FEP screen wasnt fitted properly so resin leaked all over the screen protector.
ive ordered a new FEP cause i was an idiot and ruined it on my first try, but should i order a new screen protector aswell and thoroughly clean everything?
Get a new protector especially if the resin that was wasted on the screen was cured from the light of the screen.
Helpful video - thanks!
Just curious, how long can I leave un-used resin in the vat for? Would love if I didn't have to syphon and clean after every print (just bought one, total newbie). Thanks!
A long time. There is a video on my channel about that as well
I've left mine in there for months with no problem, just make sure to stir it up before printing again.
Elbow!
haha thanks for watching
when i had a resin printer, i noticed the film started to get a foggy look. think it may came from the alcohol. i used Isopropanol . did i use the wrong alcohol? will it affect the print? uv light not getting through is?
No, that will happen over time, eventually you will have to replace the film
Why is alcohol touching the film of the vat?
@@mizokia to clean it between prints
ya missed a puddle on the front of the machine and then slid the vat over it possibly dragging it over the screen. Might wanna give that a check
You made me watch the video again haha... the scree was clean. I have since had this off again after this video all good
Where did you get the shop towels from?
I got them from the hardware store, Home Hardware here in Newfoundland
my vat is definitely scratched totally hell and I been scraping away with the spatula that came with the printer and now none of my prints been sticking smh
That will do it. There not to bad to change out
@@FacilityD20 I'm buying a new one and new screen today smh
Many manufactures had warned about using the plastic spatula on the FEP film. Please use a silicone spatula instead. The less scratches, the easier it is for prints to not get suck to the film and break off from supports.
Yes i have heard this as well.
I have resin cured to my fep film, does anybody know a good way to get that off with out damaging the fep?
Fill it up a little with IPA let is soak, try to rub the back of it with your hands and gently try to pick it off. If it is really bad you might have to replace the fep
@@FacilityD20 Thanks, I hope i can get it off.. I've printed 2 things so far on this fep and I'd hate to have to replace it already.
If your printer has a vat cleaning option, use it. If not, try running the LCD test for like 30 seconds and then just release the cured film on the vat. It will also take out the cured resin there. You can also use old cured supports from a previous print and put it in one corner and do the LCD test or cure option. Take out the vat and carefully push from beneath the vat with your fingers (not your nails) to release the film from the fep, then you just pull the old support and the film will release with it. Fep clean and good as new.
So Iv got a question for anyone here I got one from a friend and this guy gave it to me and let’s just say it went everywhere down in side of my machine does anyone have a recommendation? On how to clean this or is it trash? I don’t know please can someone help me
Try using some IPA to clean it off. If it's not on the light, and you can't clean it, put it outside and just let it cure in the sun onto the machine. All my peinter are getting full of resin too.
What about the pad above?
hardware store as well
Which gloves are you using in this video? Nitrile Powder Free? or latex ones.
Sorry I can no longer remember...
Rather than use the plastic scraper that came with the printer I see people use rubber spatulas. The spoon shaped ones in particular.
Yes, plastic can cause damage, especially if you are rough
i stopped using alcohol, just warm water does the trick boss
Thanks, I have had mix results with this, I used that for a long time, but since returned to IPA
How often should you do this?
I do it when I change resin colors or brands, or when I know I will not be printing for a few weeks. Also after failures that stick to the film.
Do you reuse the wipes?
Not the one that have Resin on them, only the ones that have IPA
Do your shop towels scratch the FEP? Or are they softer like microfiber clothes?
They are soft and lint free which is what I like about them
@@FacilityD20 nice! do they have a brand name? I'm having trouble finding something similar.
@@Jenkans not that I know of, they are generic, should find them at most hardware stores.
@@FacilityD20 thanks
Where do you get the filters?
Hardware store
the first mistake was using the plastic thing to scrape the vat.
Na. Just gently guided the resin out. However, a soft rubber is better.
Never put any cloth on your FEP. Empty the vat. Do a tank clean, remove the cured layer, squeegee what's left with a silicone spatula and wipe the vat only.
You can use a cloth. It's faster and easier. It doesn't do any harm.
Oh yes it does. The less you handle the FEP, the longer it will last.
@@FacilityD20
@kevinlee358 I agree, but so far, for me wear and tear from Printing minis and the occasional stuck print, has damaged all my fep before a lint free cloth has so far. Also dropped my magnetic build plate in there once and it cut a hole...
TBH I have stopped cleaning fep with alcohol after first two FEP short life.
What do you use now?
@@FacilityD20 stopped cleaning it. :)
Is it toxic to work at home with resin?
It's not too bad. Gloves and good ventilation are required. Most resins these days are nontoxic
@@FacilityD20 Thank you !!
It's FEP... 😉.
I know, yet I keep saying TEP over and over hahaha
but its already clean.
Not clean enough lol
this is not what to do, newer resin printer have a cleaning mode, that will solidify the first few layers and you can use a old support to pull out the sheet of resin.
That did really exist back then like it do now, I use that sometimes now to. But a also still go in and clean by hand a lot
Can't you just dunk the vat into a bucket of rinse?
Yeah i would think so
I ve seen wd40 and i was like ok not this one
You need the kind that I showed here.
Do not use the plastic spatula wtf
It's fine. Light pressure to help get the resin to flow out,
@@FacilityD20 no, it's not. That scratches fep. Use a rubber squeegie
@@NerdyCraftsmith Better then the metal one I got haha
What is your accent? I’m trying to figure it out, but I can’t place it.
Newfoundland, Canada
Ahh man you waste a lot of resin there; you can scrape all that into the bottle man; not onto the towel :) other than that, yeah cool tips :)
Edited to add - why did you scrape the resin while the vat was still on the screen; that's a really bad idea dude; if there was a weak FEP, or something that could pierce the FEP, then doing that would directly cause a spillage (never mind what others have observed about the fact that you did cause a splash that could also cause issues)...
Yeah, I wasted a bit more then normal, I blame the camera set up, I could have saved more resin for sure. There are two reasons I rubbed the bottom of the vat while in the machine: 1. to quickly check what kind of condition the resin was in, cause it was left a long time, but it had started to coagulate on the bottom, which lead me to rub it more out of curiosity haha) 2. The spill was on purpose, because I wanted to talk about and show cleaning it because of the potential issue it could cause. (I could have edited that bit out). So it was about 80% intentional and %20 curiosity hahaha.
@@FacilityD20 Yeah I just really don't think encouraging people to do that is a good idea; you could damage the fep, then the resin goes onto the screen and you have to scrape it off (ask me about that :D hah)
Cheers mate,and congrats on the channel success!!
Is it necessary to wear a mask while doing this?
Debatable. I don't, but i have good ventilation.
worst invention a vat with a very fragile film that has to be slided in over a fragile LCD screen LMAO
You have a point lol
As soon as I saw the WD-40 come out I left.
That's cool.
will this printer very smelly resin toxin when printing in process?
Personally, I don't find that bad.
04:39
na, I was gentle lol
You can use a hair dry air with cautious moderation , into it melt the resin for very easier removal. In combination with the yellow tool to help detach the stuck resin in the FEP or in LCD screen ,that makes them look dirty. after 5 minutes or so with the hair drier , on top of the resin you can detach the resin entirely , leave in one piece and if it was pancake and it will take from the FEB or LCD 99.8% of the resin . After that Handywipes or microfiber cloth for the final touches.
Thanks for the tips!
Thanks, you rock!
You're welcome!