Great video here! Every other video I've seen should be removed. Now THIS is how you do an instructional video. Everything shown in detail and explained clearly. Thanks a lot for this man. 👍🏾
Excellent step by step removal and installation of the carb. This is my exact model. They said like you said in the video. They think its the carburetor abd labour plus parts will be more than a new one. Now I know how to take it apart and I believe Amazon has the parts. Thanks for taking the time to explain in detail.
no way i did this without you. put the new carb on & runs great. with your help it was not too tough. hardest part was getting the new fuel line into the tank. great video. thanks again.☮️
Information much appreciated. I picked up a 235 and a 445, Both needing Repairs for $115. Whoever attempted to fix the 235 Put the Fuel filter on a return line, Left the old Pickup Line on (and cracked) and the old carb to primer which had several cracks. On initial testing - i.e. adding Gas to the tank - the whole Top Deck under the Carb was Flood with fuel. After reviewing this video I pulled the carb, cleaned and Flushed it well. I then followed your diagram replacing the bad fuel lines, putting a new filter on the correct line and reassembled everything. Initial starting was a bit rough but when I made the proper low/High adjustments it decided to idle and is super snappy going to max RPM. Make me happy. Now to get a clutch cover, Bar/Chain and find a buyer.
Constructive feed back, that yielded someone else success... I originally made this video for a friend, I was trying to explain this to them over the phone. It was a bit difficult so I said screw it, I have that saw, I'll make a video for you. The others it helped is just icing on the cake. Still a bit of a warm fuzzy feeling to it tho.
Looked at a lot of videos. This is best of all. Hand drawn diagram finally made sense to me. Appreciate your clear communication abilities. Thanks a bunch!
Having watched your video and by coincidence a Husqvarna was dumped on me to have a new carb fitted, and your video just made the job relatively easy, thank you!
I wish all do it yourself videos were as detailed as yours, I appreciate your time & expertise on tis particular chain saw ... I was going to trash it until i found your video Thanks a lot!!!
I put a new bar and chain on mine to correct a crooked cut. After, my saw decided to not start. Thinking it was an old fuel or carb issue, I took out cleaned, replaced the spark plug and tuned. Okay the saw is running like a champ again!Then ran into a no start issue again. Primer bulb was only half full so I’m thinking I need to replace my fuel lines. I’ve already put money into the saw so I might as well keep going till it’s fixed. Great video, thanks.
Great video and saved me a ton of time and money. I have a 235e, and it took me a couple of tries getting it back together because I got the screws mixed up, would've like a little more detail on that, plus mine has two different sizes of gas tubing, a smaller one for the main gas line from the filter, and two lines next size larger for bulb/primer. Otherwise, many kudos for an excellent job!!!Thank you!!
Thanks for the very well done video, it explained how to take the saw apart enough to get at the fuel lines and carb and a very good explanation of how the primer bulb actually works. I was able to replace the fuel line from the carb to the tank without removing the carb, once it got in the tank, was able to grab it with a pick and pull it thru. A fiddly job but not difficult.
Thank you so much for making this video. It was clear, understandable and I think for me so convenient to be able to rewind as I took the steps necessary to complete attaching the hoses to the proper place. I appreciate your efforts. Jim Simmons.
Super video dude.i repair small engines as a profession but i still like to watch the onlines.you didnt miss a single step and no bullshit.take me to the river drop me in the water.nice job...the world needs more men like us.
Very well done Sir! Saw would quit running several minutes after a full tank, rotten fuel lines were sucking air as soon as the fuel level dropped. I shoulda looked for this before I started unscrewing everything. But, yeah, I googled "Husqvarna fuel flow diagram" and bingo. I won't say what I learned about those four screws on the bottom of the motor but you did remember for me the three finger tubing puzzle. All is well in the end, 17 year old unit saved from the recycle yard for a couple hours & $20 and saved about $300.
You won at TH-cam for today. Thanks! I got my saw back from a "small engine" joint after having them replace cracking fuel lines, filter and bulb. Prime, choke, pull, half-choke, pull and it ran great... For 4 seconds. They had the bulb backwards and the filter on the wrong side. Working now. Again, thanks!
Excellant video great detail. Especially choke lever position. Originally had it installed wrong. I was able to change the carb but had to do it twice. I forgot to install the gasket. Noticed the old gasket on the old one after I installed the carb Your detailed instructions helped alot. It runs now but have to adjust hi low settings. It stalls when I pull the trigger.
When I was changing the gas line on mine I figured that the line taking gas from the purge back to the tank was the gas line and pulled it out and costed my self a lot of work, this shows to do research first. Cause good people like you who know their stuff make videos on it. Crazy!
great video dude. One of the best I've seen on TH-cam especially on a very difficult saw to service the fuel lines. You're the only one that had a video that directly addressed when I have to do. The masses thank you
It feels really good to get that kind of feed back.... Many of these end up in a landfill long before their time because of the price point, and for many the parts are cheap to get back into service, unfortunately the labor is not. So much waste comes from this industry, its a good feeling helping others avoid that, even if be on a small scale.
Thank you for the in depth video this was great!!! My issue was I bought mine from a pawn shop and well lets say never again with out a full take down and deep dive into finding out what the heck someone else did to the dam thing! cost me almost as much as a new saw to replace the worn out parts I think I am 15$ less at this point and I need to replace the bottom fuel line because they used the wrong one and it leaks from the tank as you try and prime it so the saw does not stay running because it sucks air and then dies!
this is the best vid i have watched on changing these carbs i have a 240 that bogs down at full throttle and for the price of a carb i am going to change it
Outstanding information,! Very helpful, And kept it simple for me to get the picture in my mind and not forget when I go out to fix my problem 😀 Thanks !
Great video. Appreciate you taking apart a running saw to show us how. Do note the bolt holes through the black plastic carb piece are way too tight. That's the pinch point. Ream those out once you get it apart to make future cleaning easier.
Awesome video. Made everything easy except feeding the priming button tube back into the back of the tank. Needle nose players could not reach back far enough to grab it and pull it in.
Helped me a lot, fixing to tackle this job. I guess it’s best to use non Ethanol fuel even though I’ve always drained most of the fuel out when storing but the saw is about ten years old so it’s due.
Well done! Great video! I've had a few chainsaws where the fuel line depletes over time and drops the filter in the tank. What a load of bollx. You need to learn to fix them yourself or they just become disposable trash. But thanks for posting this. PS.. I get the fuel line kits from Lowes or HomeDepot
Great info. Helped me out a ton! I have ONE question though. Do both hoses in the tank have a filter on them? One had a filter the other didn’t in my case.
Well I may ask you a question about my Husqvarna 326 that I bought from a fellow ...It started when he tested it but the day after I only enjoyed it fifteen minutes then it become a night mare ...to make the long story short I replaced the carburettor --a new one from China -- And stil didn't start and because it is hard to pull the rope i decided to have a look the the piston and the cylinder ... The piston shows a scratch on the muffler side it has not damaged the ring and the cylinder ....Then I removed the ring and fitted it in cylinder it has a gup about one millimetre....it's ok or do I have to replace the piston and the ring ? I appreciate your help Thank you
I am asking to myself should I disturb you or not since I never got an answer to my question a couple weeks ago since then to my surprise the chainsaw works but I can get the new primary working I connected as per your diagram but no fuel flows in out actually the bulb get stuck and does not come back so a you said long little tube the fuel line (out) to the tank the short one (inlet) from carburettor to the bulb .Any suggestions ?
Putting my chainsaw back together, I ran into a problem. No matter what I do I can not get the fuel line back through the whole to the tank. I tried lubing it and shaving the tip of the tubing. I need suggestions. Thanks
This is about as simple and straightforward as it gets. Great fuel line vid, the best I found. If I can understand it so can anyone. Just one question, maybe 2: How far into the tank does the return line need to be? Does it really need that little nipple on the end? How much play is needed in the line with the fuel filter? No doubt it's going to move around, but is there a goal with how it lays and where the filter usually drops?
Execellent video. I'm replacing my 235 carburetor and fuel lines now. Any suggestions on how to replace the fuel line that travels from the bubble back to the fuel tank? looks like it has something at the end of the line inside the tank that keeps it from being removed.
Yes the white piece on the end of the fuel line is just for that, to keep it from pulling out. Easier to pull it out through the gas tank, and put the piece back on similar to the fuel filter. Sorry for the delayed reply, hope this helps.
Where do those two wires go. I can see where the yellow goes but the other one fell off when I was changing the carb and I can’t figure out where it was
Good info, used some curved hemostats (surgeon style pliers you see medics clamping onto arteries in ww2/nam movies) Fits in the gas tank perfectly to clamp onto the cut needlepoint in the hose you mentioned. Cheap too.
Those are an awesome tool to have around... very useful for machines where the gas cap hole is in a awkward spot (for me, certain back pack blowers come to mind.) That and it feels cool using them.
I've got this exact model and I really need your help. I have to replace the fuel lines and purge bulb which is not too difficult for me to do. What I'm not sure about is the fuel tank vent ( I accidentally pulled out the check valve (duckbill) while trying to pull out the old fuel line that goes into the fuel line fitting. So that needs to be replaced. I understand that I need to drill a hole in the vent and pull it out with a screw. I also pulled out the fuel line fitting so I'm not sure how the fuel line/s needs to be installed. Is there a piece of fuel line that needs to be ran from the top of the bubble into the bottom of the tank from the bottom of the fitting? Sorry for all of the questions.
Finally somebody did a simple instructive video that shows you and tells you exactly what you need to know I swear there's nine thousand different videos and they all go around what you need to know and never cover a single bit of it I was trying to verify the way the fuel lines ran on the soil and apparently I do have them the correct way thanks for actually making a video it has good information in it
Great video here! Every other video I've seen should be removed. Now THIS is how you do an instructional video. Everything shown in detail and explained clearly. Thanks a lot for this man. 👍🏾
Excellent step by step removal and installation of the carb. This is my exact model. They said like you said in the video. They think its the carburetor abd labour plus parts will be more than a new one. Now I know how to take it apart and I believe Amazon has the parts. Thanks for taking the time to explain in detail.
This was exactly what I needed. Thank you so much for making this video.
no way i did this without you. put the new carb on & runs great. with your help it was not too tough. hardest part was getting the new fuel line into the tank. great video. thanks again.☮️
I originally made this video to help a friend who lives far away.... the other people its helped... I'm glad i made it. Your welcome.
Information much appreciated.
I picked up a 235 and a 445, Both needing Repairs for $115.
Whoever attempted to fix the 235 Put the Fuel filter on a return line, Left the old Pickup Line on (and cracked) and the old carb to primer which had several cracks. On initial testing - i.e. adding Gas to the tank - the whole Top Deck under the Carb was Flood with fuel.
After reviewing this video I pulled the carb, cleaned and Flushed it well. I then followed your diagram replacing the bad fuel lines, putting a new filter on the correct line and reassembled everything.
Initial starting was a bit rough but when I made the proper low/High adjustments it decided to idle and is super snappy going to max RPM. Make me happy.
Now to get a clutch cover, Bar/Chain and find a buyer.
Thank you sir. Performing this repair tomorrow on our Huskie 235. Appreciate the work you put in sharing your knowledge.
Nice job on this video. I was able to successfully replace my fuel line after watching this. Much appreciated!!
Outstanding video! A huge help in assisting the removal and replacement of a new carb. Thank you.
Great video! Couldn’t have done it without you! Much appreciated!
excellent video. Followed your instructions and got my 240 up and running 15 mins ago. thank you
Constructive feed back, that yielded someone else success... I originally made this video for a friend, I was trying to explain this to them over the phone. It was a bit difficult so I said screw it, I have that saw, I'll make a video for you.
The others it helped is just icing on the cake. Still a bit of a warm fuzzy feeling to it tho.
The most detailed chainsaw video out there. Thank you for explaining every step thoroughly!
Looked at a lot of videos. This is best of all. Hand drawn diagram finally made sense to me. Appreciate your clear communication abilities. Thanks a bunch!
Having watched your video and by coincidence a Husqvarna was dumped on me to have a new carb fitted, and your video just made the job relatively easy, thank you!
I wish all do it yourself videos were as detailed as yours, I appreciate your time & expertise on tis particular chain saw ... I was going to trash it until i found your video Thanks a lot!!!
Clear, to-the-point instructions. No nonsense. Wonderful. Thank you.
Appreciate the video. Nice step by step. Saved me from buying a new saw which would've been a huge waste for such a simple fix. Thanks
I put a new bar and chain on mine to correct a crooked cut. After, my saw decided to not start. Thinking it was an old fuel or carb issue, I took out cleaned, replaced the spark plug and tuned. Okay the saw is running like a champ again!Then ran into a no start issue again. Primer bulb was only half full so I’m thinking I need to replace my fuel lines.
I’ve already put money into the saw so I might as well keep going till it’s fixed.
Great video, thanks.
Great video and saved me a ton of time and money. I have a 235e, and it took me a couple of tries getting it back together because I got the screws mixed up, would've like a little more detail on that, plus mine has two different sizes of gas tubing, a smaller one for the main gas line from the filter, and two lines next size larger for bulb/primer. Otherwise, many kudos for an excellent job!!!Thank you!!
Thanks for the very well done video, it explained how to take the saw apart enough to get at the fuel lines and carb and a very good explanation of how the primer bulb actually works. I was able to replace the fuel line from the carb to the tank without removing the carb, once it got in the tank, was able to grab it with a pick and pull it thru. A fiddly job but not difficult.
So I watched this a bit ago and now it turns out I really needed it, My feed line was totally rotted out. Thank you so much.
GREAT EXPLANATIONS, very helpful, thanks .
Excellent video! I always read through the comments for additional information. Thank you for sharing.
Thank you so much for making this video. It was clear, understandable and I think for me so convenient to be able to rewind as I took the steps necessary to complete attaching the hoses to the proper place. I appreciate your efforts. Jim Simmons.
Super video dude.i repair small engines as a profession but i still like to watch the onlines.you didnt miss a single step and no bullshit.take me to the river drop me in the water.nice job...the world needs more men like us.
The best shop class yet great going helps a lot😊
Very well done Sir!
Saw would quit running several minutes after a full tank, rotten fuel lines were sucking air as soon as the fuel level dropped.
I shoulda looked for this before I started unscrewing everything.
But, yeah, I googled "Husqvarna fuel flow diagram" and bingo.
I won't say what I learned about those four screws on the bottom of the motor but you did remember for me the three finger tubing puzzle.
All is well in the end, 17 year old unit saved from the recycle yard for a couple hours & $20 and saved about $300.
You won at TH-cam for today. Thanks!
I got my saw back from a "small engine" joint after having them replace cracking fuel lines, filter and bulb. Prime, choke, pull, half-choke, pull and it ran great... For 4 seconds.
They had the bulb backwards and the filter on the wrong side. Working now.
Again, thanks!
That's like the worse of both worlds...had to pay to get your saw worked on, and had to work on it yourself anyway. I'm sorry to hear that.
How much did that cost you at the small engine shop? I'd like to chant the cost I'm saving as I do this work for myself!
Excellant video great detail.
Especially choke lever position. Originally had it installed wrong.
I was able to change the carb but had to do it twice.
I forgot to install the gasket.
Noticed the old gasket on the old one after I installed the carb
Your detailed instructions helped alot.
It runs now but have to adjust hi low settings. It stalls when I pull the trigger.
When I was changing the gas line on mine I figured that the line taking gas from the purge back to the tank was the gas line and pulled it out and costed my self a lot of work, this shows to do research first. Cause good people like you who know their stuff make videos on it. Crazy!
The many things I unfortunately have had to learn the hard way... but those experiences are the ones that usually stick.
Great explanation of how to change fuel lines and carburetor
Hey man what a great video.. very easy to follow the instructions. Keep at them buddy 🏴
great video dude. One of the best I've seen on TH-cam especially on a very difficult saw to service the fuel lines. You're the only one that had a video that directly addressed when I have to do. The masses thank you
It feels really good to get that kind of feed back.... Many of these end up in a landfill long before their time because of the price point, and for many the parts are cheap to get back into service, unfortunately the labor is not.
So much waste comes from this industry, its a good feeling helping others avoid that, even if be on a small scale.
Thank you for the in depth video this was great!!! My issue was I bought mine from a pawn shop and well lets say never again with out a full take down and deep dive into finding out what the heck someone else did to the dam thing! cost me almost as much as a new saw to replace the worn out parts I think I am 15$ less at this point and I need to replace the bottom fuel line because they used the wrong one and it leaks from the tank as you try and prime it so the saw does not stay running because it sucks air and then dies!
this is the best vid i have watched on changing these carbs i have a 240 that bogs down at full throttle and for the price of a carb i am going to change it
Had since 2010 been use several times and fuel lines all crumbled.Pretty detailed Nice 👍 thank you!!!
You had the best instruction for this job . Thank so much
Fantastic video, really well explained and perfect level of detail. Thank you
Well done video. Thank you for taking the time to make it.
Thank you, this is a brilliant video. I was able to fix my chainsaw thanks to you
Thank you so much. You know how to explain things!
Outstanding information,! Very helpful, And kept it simple for me to get the picture in my mind and not forget when I go out to fix my problem 😀 Thanks !
Thanks dude! You’re a lifesaver 👍🏻👍🏻
Yea this is awesome! Thanks for taking the time to help us!
Great video. Appreciate you taking apart a running saw to show us how. Do note the bolt holes through the black plastic carb piece are way too tight. That's the pinch point. Ream those out once you get it apart to make future cleaning easier.
Great video, very thoughtful steps. Hoping you make more for the other tools I own!
My go to video everytime I get one of these. 👍🏻👊🏻
Very good breakdown and assemble. Exactly the info I was looking for
Awesome video. Made everything easy except feeding the priming button tube back into the back of the tank. Needle nose players could not reach back far enough to grab it and pull it in.
you saved me my friend,keep up the great video's.
U would make a good teacher
What a fantastic vijayo.. You Sir, do not talk to us dummies like dummies!! Hat's off to ya.. Thanks. K
Thank you, I really wanted to help people out, not talk down to them, so I'm glad to hear that.
Great video simple and to the point!
GREAT JOB. I LEARNED A LOT. THANK YOU
Very helpful about fuel lines ☺️☺️☺️
Helped me a lot, fixing to tackle this job. I guess it’s best to use non Ethanol fuel even though I’ve always drained most of the fuel out when storing but the saw is about ten years old so it’s due.
That was great instruction. Thank-you
This really is a good video! Thank you very much for putting it together.
Thanks bud, you saved my life, I was going nuts until I saw this video! lifesaver.... You da man'
Glad I could help.
Great instructional video excellent job
Great Video. Very detailed and well explained - Thank You !!
Well done! Great video!
I've had a few chainsaws where the fuel line depletes over time and drops the filter in the tank. What a load of bollx. You need to learn to fix them yourself or they just become disposable trash.
But thanks for posting this.
PS.. I get the fuel line kits from Lowes or HomeDepot
Thanks it helped me out very good video
My Jonsered cs2238; disassemble and gas line are the same. Great Video!! Should have watched video first would have saved me some time.
Great info. Helped me out a ton! I have ONE question though. Do both hoses in the tank have a filter on them? One had a filter the other didn’t in my case.
Very good and well told and described. Tops.👍👍
Thanks man. Very good instructions !!
Right on, your welcome.
Just finished....thanks again.
Your welcome.
exactly the video i needed . . . thanks .
excellent video!
Well I may ask you a question about my Husqvarna 326 that I bought from a fellow ...It started when he tested it but the day after
I only enjoyed it fifteen minutes then it become a night mare ...to make the long story short I replaced the carburettor --a new one from China --
And stil didn't start and because it is hard to pull the rope i decided to have a look the the piston and the cylinder ...
The piston shows a scratch on the muffler side it has not damaged the ring and the cylinder ....Then I removed the ring and fitted
it in cylinder it has a gup about one millimetre....it's ok or do I have to replace the piston and the ring ?
I appreciate your help Thank you
Thanks for saving me some unnecessary disassembly. By just looking at the saw, it's not clear just what needs to come apart to get to the problem.
You really learn what you think you know, when you try teach some one else. Its an eye opening experience. Your welcome.
I am asking to myself should I disturb you or not since I never got an answer to my question a couple weeks ago
since then to my surprise the chainsaw works but I can get the new primary working I connected as per your diagram
but no fuel flows in out actually the bulb get stuck and does not come back so a you said long little tube the fuel line (out)
to the tank the short one (inlet) from carburettor to the bulb .Any suggestions ?
Great Video Thanks
Putting my chainsaw back together, I ran into a problem. No matter what I do I can not get the fuel line back through the whole to the tank. I tried lubing it and shaving the tip of the tubing. I need suggestions. Thanks
great video man !! well done mate i fixed my chainsaw with this video . cheers
Very helpful ! Thanks
This is about as simple and straightforward as it gets. Great fuel line vid, the best I found. If I can understand it so can anyone. Just one question, maybe 2: How far into the tank does the return line need to be? Does it really need that little nipple on the end? How much play is needed in the line with the fuel filter? No doubt it's going to move around, but is there a goal with how it lays and where the filter usually drops?
I didn't ask bout no 235240what ever came uo
Very good job.
Great video Dude , thanks 🙏🏼
Execellent video. I'm replacing my 235 carburetor and fuel lines now. Any suggestions on how to replace the fuel line that travels from the bubble back to the fuel tank? looks like it has something at the end of the line inside the tank that keeps it from being removed.
Yes the white piece on the end of the fuel line is just for that, to keep it from pulling out. Easier to pull it out through the gas tank, and put the piece back on similar to the fuel filter. Sorry for the delayed reply, hope this helps.
Just watching this halway through my rebuild, 11:47 i can guarentee you this wouldve drove me crazy
Do not forget there a air hole that goes to the tank in the botton right corner it needs to be clean in them models.
Good job. Like it thanks man.
Where do those two wires go. I can see where the yellow goes but the other one fell off when I was changing the carb and I can’t figure out where it was
Good info, used some curved hemostats (surgeon style pliers you see medics clamping onto arteries in ww2/nam movies) Fits in the gas tank perfectly to clamp onto the cut needlepoint in the hose you mentioned. Cheap too.
Those are an awesome tool to have around... very useful for machines where the gas cap hole is in a awkward spot (for me, certain back pack blowers come to mind.) That and it feels cool using them.
Awesome video, can brake cleaner be used to clean up chainsaw while it is apart or will it be to caustic for rubber and plastic hoses?
I've got this exact model and I really need your help. I have to replace the fuel lines and purge bulb which is not too difficult for me to do. What I'm not sure about is the fuel tank vent ( I accidentally pulled out the check valve (duckbill) while trying to pull out the old fuel line that goes into the fuel line fitting. So that needs to be replaced. I understand that I need to drill a hole in the vent and pull it out with a screw. I also pulled out the fuel line fitting so I'm not sure how the fuel line/s needs to be installed. Is there a piece of fuel line that needs to be ran from the top of the bubble into the bottom of the tank from the bottom of the fitting? Sorry for all of the questions.
You must b a midwest boy.nice clear speech
Finally somebody did a simple instructive video that shows you and tells you exactly what you need to know I swear there's nine thousand different videos and they all go around what you need to know and never cover a single bit of it I was trying to verify the way the fuel lines ran on the soil and apparently I do have them the correct way thanks for actually making a video it has good information in it
Great video, good details, spot on...well done.
Thank you, I appreciate the feed back, good or bad.
Do you have video, how to replace the fuel pump ( the rubber fuel riser )
Very helpful and well explained. Thank you very much.
Good stuff man thanks
Thanks buddy, great video
Nice work on the video. Is there a check valve inside of the tank on a 235?
Thank you
Trying to save this video for when my amazon parts come in.
Love the diagram mang!
Nice vid, but can you tell me how long to leave the fuel line inside the tank?
GREAT VIDEO 👍