At last a video with someone changing the slam panel, every video ive seen they make brackets for the lights or skip that part of fitting . I bought a T5.1 front end and it came with top panel . The 2 bolts that hold the bumper to the wings were rusty as hell everyones look mint 😂 progress so far bonnet and freshly painted wings are on but as you know headlights need to be fixed to the panel . I didn't get the bottom bumper plate and as you not say if t5 will accept the bumper am a bit lost ! Half of my bumper bolts were missing to start with and i bought plug and play harness for the lights but appreciate you have taken time to show how you have wired and shown every part number . Ive decided now to fit the slam panel ive got this far and want it to be done right . Luckily i have some idea what am doing but again am lost with bottom bumper bracket and some brackets your showing Thumbs down . Do you have the slow motion video anywhere on you tube ??
Thanks for the vid and very appreciated!!! Question, is this correct ...do i connect a new wire into pin no. 4 on the left headlight connector and the same for the right side headlight connector? If this is correct, where do i connect the new wire into ...the fusebox or anywhere else?!🤔🤷♂️
Not remember 100% but just try this: 1. H7 Low Beam: • Pin 2: Connect the ground wire (usually brown). • Pin 4: Connect the power wire (typically white or yellow). 2. H15 High Beam and DRL: • High Beam: • Pin 1: Connect the power wire for the high beam (usually white or yellow). • Pin 2: Connect the ground wire (usually brown). • Daytime Running Lights (DRL): • Pin 3: Connect the power wire for the DRL (typically grey or green). Color and Pin Configuration: • Pin 1: High Beam Power (White or Yellow) • Pin 2: Ground (Brown) • Pin 3: DRL Power (Grey or Green) • Pin 4: Low Beam Power (White or Yellow)
Hi there, I did a face lift but have a problem. My new headlights point low when on dip and when I switch to full beam they point way too high. Any advice for me? Thanks
@@CheckEnginePlusMinus I hope you will do it... Congrats again.. I just bought a T5 High Roof and planning to facelift it toT6 or t6.1.. If I face any problem ,be sure I ll keep contact with you ; if you dont mind.. Take care.
@@pontoxs1 hi huseyin, I facelifted my van to t5.1. If you need to facelift to t6 you will need to change wings, slam panel and water bottle and also brackets. T5.1 is much easier
@@gerryhannan9463 Hi Berti.. Thanks for your message. . I started facelift yesterday and it seems the result Will be good.. But after I read your message, i realised that I missed to buy water bottle. It should be changed with T6' water bottle?
@@pontoxs1 I think it has to be changed to fit, I remember reading it online but I think you should try without it and maybe save some money! Good luck
Wszystko zależy od tego za ile uda się wyrwać części blacharskie + ewentualnie lakiernik ( poliftowe już mają troszkę inny kod lakieru i będzie różnica).
Radio upgrade from VW t5.1 to t5 th-cam.com/video/22c1rmCqFr4/w-d-xo.html
Big up ! Greeting from Kingdom of Morocco !!
💪💪💪💪💪
Fajne wygladą! Zrobie na swoim T5 lift)
At last a video with someone changing the slam panel, every video ive seen they make brackets for the lights or skip that part of fitting . I bought a T5.1 front end and it came with top panel . The 2 bolts that hold the bumper to the wings were rusty as hell everyones look mint 😂 progress so far bonnet and freshly painted wings are on but as you know headlights need to be fixed to the panel . I didn't get the bottom bumper plate and as you not say if t5 will accept the bumper am a bit lost ! Half of my bumper bolts were missing to start with and i bought plug and play harness for the lights but appreciate you have taken time to show how you have wired and shown every part number . Ive decided now to fit the slam panel ive got this far and want it to be done right . Luckily i have some idea what am doing but again am lost with bottom bumper bracket and some brackets your showing Thumbs down . Do you have the slow motion video anywhere on you tube ??
Hi could you expain pin 4 of the headlight further. Thank you
Thanks for the vid and very appreciated!!! Question, is this correct ...do i connect a new wire into pin no. 4 on the left headlight connector and the same for the right side headlight connector? If this is correct, where do i connect the new wire into ...the fusebox or anywhere else?!🤔🤷♂️
Hello. Do you have wiring diagram for H7 & H15 double lights?
Not remember 100% but just try this:
1. H7 Low Beam:
• Pin 2: Connect the ground wire (usually brown).
• Pin 4: Connect the power wire (typically white or yellow).
2. H15 High Beam and DRL:
• High Beam:
• Pin 1: Connect the power wire for the high beam (usually white or yellow).
• Pin 2: Connect the ground wire (usually brown).
• Daytime Running Lights (DRL):
• Pin 3: Connect the power wire for the DRL (typically grey or green).
Color and Pin Configuration:
• Pin 1: High Beam Power (White or Yellow)
• Pin 2: Ground (Brown)
• Pin 3: DRL Power (Grey or Green)
• Pin 4: Low Beam Power (White or Yellow)
Please write down your biggest problems with changing the front! 💪💪
Hi! What does this means? After connect to light switch pin nr3 tfl
What is tfl?
Great video , what's the tune ?
thanks I don't remember
The tune: Mama Zula «i feel good»
Hi there,
I did a face lift but have a problem. My new headlights point low when on dip and when I switch to full beam they point way too high. Any advice for me? Thanks
Hello what its your headlights OEM Part number?
@@CheckEnginePlusMinus I have no idea, will I find that on the headlight?
Dou you think that it can be possible to facelift from T5 to T6.1 as well ?
yes, without any problems💪
@@CheckEnginePlusMinus I hope you will do it... Congrats again.. I just bought a T5 High Roof and planning to facelift it toT6 or t6.1.. If I face any problem ,be sure I ll keep contact with you ; if you dont mind.. Take care.
@@pontoxs1 hi huseyin, I facelifted my van to t5.1. If you need to facelift to t6 you will need to change wings, slam panel and water bottle and also brackets. T5.1 is much easier
@@gerryhannan9463 Hi Berti.. Thanks for your message. . I started facelift yesterday and it seems the result Will be good.. But after I read your message, i realised that I missed to buy water bottle. It should be changed with T6' water bottle?
@@pontoxs1 I think it has to be changed to fit, I remember reading it online but I think you should try without it and maybe save some money! Good luck
perfecttttt!!! OMG
thanks :-)
Jaki koszt takiego przerobienia
Wszystko zależy od tego za ile uda się wyrwać części blacharskie + ewentualnie lakiernik ( poliftowe już mają troszkę inny kod lakieru i będzie różnica).
@@CheckEnginePlusMinus Czyli lepiej nie przerabiać.
👌
Danke :-)
Szkoła druciarstwa
Liczy się efekt końcowy 🙃
Słabo to wyglada
Dziękuję za opinię 🤩